Related Manuals for New Holland T8.275
Summary of Contents for New Holland T8.275
- Page 1 SERVICE MANUAL T8.275 / T8.300 / T8.330 / T8.360 / T8.390 Tractor PIN ZBRC07000 and after Part number 47386189 English October 2012 Copyright © 2012 CNH America LLC. All Rights Reserved.
- Page 2 SERVICE MANUAL T8.275 [ZBRC07000 - ] , T8.300 [ZBRC07000 - ] , T8.330 [ZBRC07000 - ] , T8.360 [ZBRC07000 - ] , T8.390 [ZBRC07000 - ] 47386189 26/06/2012...
- Page 3 Contents INTRODUCTION Engine..................10 Engine and crankcase ..............10.001 Cylinder heads .
- Page 4 Powered rear axle ............... . 27.100 Rear bevel gear set and differential .
- Page 5 Hydraulic control components ............41.200 Pump .
- Page 6 Pneumatically-adjusted operator seat ........... . 90.124 Cab .
- Page 7 47386189 26/06/2012...
- Page 8 INTRODUCTION 47386189 26/06/2012...
-
Page 9: Table Of Contents
Safety rules ..................3 T8.275 WE, T8.300 WE, T8.330 WE, T8.360 WE, T8.390 WE Safety rules . -
Page 10: Safety Rules
INTRODUCTION Safety rules T8.275 WE, T8.300 WE, T8.330 WE, T8.360 WE, T8.390 WE Personal safety This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible death or injury. -
Page 11: Safety Rules
INTRODUCTION Safety rules T8.275, T8.300, T8.330, T8.360, T8.390 Standard safety precautions Be informed and notify personnel of the laws in force regulating safety, and provide documentation available for consultation. Keep working areas as clean as possible. • Ensure that working areas are provided with emergency boxes. They must be clearly visible and always contain •... - Page 12 INTRODUCTION Never disconnect the batteries while the engine is running. • Disconnect the batteries prior to performing any work on the equipment. • Disconnect the batteries to place a load on them with a load tester. • After any work is performed, verify that the battery clamp polarity is correct and that the clamps are tight and •...
-
Page 13: Basic Instructions - Important Notice Regarding Equipment Servicing
Some information could not be updated due to modifications of a technical or commercial type, or changes to the laws and regulations of different countries. In case of questions, refer to your NEW HOLLAND AGRICULTURE Sales and Service Networks. 47386189 26/06/2012... -
Page 14: Torque - Minimum Tightening Torques For Normal Assembly
INTRODUCTION Torque - Minimum tightening torques for normal assembly T8.275, T8.300, T8.330, T8.360, T8.390 METRIC NON-FLANGED HARDWARE NOM. LOCKNUT LOCKNUT SIZE CL.8 CL.10 CLASS 8.8 BOLT and CLASS 10.9 BOLT and W/CL8.8 W/CL10.9 CLASS 8 NUT CLASS 10 NUT BOLT... - Page 15 INTRODUCTION METRIC FLANGED HARDWARE NOM. CLASS 8.8 BOLT and CLASS 10.9 BOLT and LOCKNUT LOCKNUT SIZE CLASS 8 NUT CLASS 10 NUT CL.8 CL.10 W/CL8.8 W/CL10.9 BOLT BOLT PLATED PLATED UNPLATED UNPLATED W/ZnCr W/ZnCr 2.4 N·m (21 lb 3.2 N·m (28 lb 3.5 N·m (31 lb 4.6 N·m (41 lb 2.2 N·m (19 lb...
- Page 16 INTRODUCTION Manufacturer's Identification Property Class Clock Marking of Property Class and Manufacturer's Identification (Optional), i.e. marks 60 ° apart indicate Class 10 properties, and marks 120 ° apart indicate Class 8. INCH NON-FLANGED HARDWARE LOCKNUT LOCKNUT NOMINAL SAE GRADE 5 BOLT SAE GRADE 8 BOLT GrB W/ Gr5 GrC W/ Gr8...
- Page 17 INTRODUCTION INCH FLANGED HARDWARE NOM- LOCKNUT LOCKNUT SAE GRADE 5 BOLT and SAE GRADE 8 BOLT and INAL GrF W/ Gr5 GrG W/ Gr8 SIZE BOLT BOLT UNPLATED PLATED UNPLATED PLATED or PLATED W/ZnCr or PLATED W/ZnCr SILVER GOLD SILVER GOLD 12 N·m (106 lb 13 N·m (115 lb...
- Page 18 INTRODUCTION Inch Lock Nuts, All Metal (Three optional methods) 20090268 Grade Identification Grade Corner Marking Method (1) Flats Marking Method (2) Clock Marking Method (3) Grade A No Notches No Mark No Marks Grade B One Circumferential Notch Letter B Three Marks Grade C Two Circumferential Notches...
-
Page 19: Capacities
INTRODUCTION Capacities T8.275, T8.300, T8.330, T8.360, T8.390 System Metric U.S. Imperial 9.0 l engine Engine oil – no filter change 25 l 6.6 US gal 5.5 UK gal 25 l 5.5 UK gal Engine oil– with filter change 6.6 US gal Cooling system 26.5 l... - Page 20 SERVICE MANUAL Engine T8.275 WE T8.300 WE T8.330 WE T8.360 WE T8.390 WE 47386189 26/06/2012...
- Page 21 Thanks very much for your reading, Want to get more information, Please click here, Then get the complete manual NOTE: If there is no response to click on the link above, please download the PDF document first, and then click on it. Have any questions please write to me: admin@servicemanualperfect.com...