Table of Contents
Related Manuals for Hakko Electronics FT-8003
Summary of Contents for Hakko Electronics FT-8003
- Page 1 THERMAL WIRE STRIPPER FT-802 Instruction Manual Thank you for purchasing the HAKKO FT-802 Thermal Wire Stripper. Be sure to read this manual before operating the HAKKO FT-802. Keep this manual readily accessible for reference.
-
Page 2: Table Of Contents
Table of Contents PACKING LIST AND PART NAMES ............1 SPECIFICATIONS ................... 1 WARNINGS, CAUTIONS AND NOTES ..........2 INITIAL SETUP ..................3 4-1 Blades ....................3 4-1-1 Attaching blades ..............3 4-1-2 Removing blades ..............3 4-1-3 Blade holder ................3 4-2 Station ....................4 HOW TO USE ..................4 5-1 Operation and display (switch and operation buttons) .....4 5-2 Setting/changing output ..............4 5-3 Handle ....................5... -
Page 3: Packing List And Part Names
1. PACKING LIST AND PART NAMES Please make sure that all items listed below are included in the package. Blade removal plate Handle holder Lead adjuster Instruction Manual Blade (not included) Power switch HAKKO FT-802 HAKKO FT-8004 Hexagon socket set screw Receptacle Plug Inlet... -
Page 4: Warnings, Cautions And Notes
3. WARNINGS, CAUTIONS AND NOTES Warnings and cautions are placed at critical points in this manual to direct the operator’s attention to significant items. They are deemed as follows: WARNING : Failure to comply with a WARNING may result in serious injury or death. CAUTION : Failure to comply with a CAUTION may result in injury to the operator, or damage to the items involved. -
Page 5: Initial Setup
4. INITIAL SETUP 4-1 Blades 4-1-1 Attaching blades V-groove 1. Insert the blades fully and match the V-groove on the blades to the V-groove on the mounting flange. Push until blades are flush with mounting flange. 2. Insert the hexagon socket set screws but do not tighten. -
Page 6: Station
4. INITIAL SETUP (continued) 4-2 Station 1. Connect the power cord to the inlet on the rear side of the station. 2. Place the HAKKO FT-8004 on the handle holder with the blades facing up. 3. Plug the handle plug into the receptacle. 4. -
Page 7: Handle
― NOTE ― The output value range is 5% to 100%. The output values can be set in increments of 5%. If the output is 80% or less, will be displayed when the handpiece is placed on the station indicating the timer start for the auto sleep setting set by parameter 02. -
Page 8: How To Use The Lead Adjuster
5. HOW TO USE (continued) 5-3-2 How to use the lead adjuster The lead adjuster is a tool for setting the wire stripping length. Adjuster plate Adjust the distance between the blade end and the adjuster plate to the desired wire stripping length and slide it. -
Page 9: Setting Parameters
6. SETTING PARAMETERS To make this product more convenient to use, the HAKKO FT-802 has the following parameters which can be set. The parameter settings can be changed to suit your use environment. • Password setting • Auto sleep enable/disable setting Setting a password allows you to lock the settings The auto sleep function can be enabled or disabled. -
Page 10: Parameter Setting Procedure
6. SETTING PARAMETERS (continued) 6-2 Parameter setting procedure Parameter input mode flowchart Follow the steps below to input parameter values. 1. Hold the buttons pressed while switching on the power to enter parameter input mode. 2. Select the parameter number. Initially, the parameter number will be blinking. - Page 11 Password setting Setting a password enables the set output value or parameter values to be locked. The password is set by selecting a combination of 3 characters from among the 6 characters of The password setting has 3 levels. : Disabled. (No lock) : Partially enabled.
- Page 12 6. SETTING PARAMETERS (continued) WARNING The high temperature at 105% to 120% could shorten blade life or that the blade will glow red. Place the handle on the handle holder when not using the HAKKO FT-802. High output setting Enable or disable the high output function. This function operates when the password setting mode is set to (partially enabled) or (enabled).
- Page 13 Auto sleep time setting This function operates when the Auto sleep enable/disable setting is set to (enabled). Set the time until the auto sleep function operates after placing the handle on the handle holder. When the time is set , the auto sleep function starts immediately after placing the handle on the handle holder. Display: is lit.
-
Page 14: Maintenance
7. MAINTENANCE The unit should be maintained periodically to be able to use it in proper condition for a long time. Since the degree of consumption of the unit varies depending on the use temperature, etc., perform maintenance of the unit according to use conditions. WARNING Since the unit can reach a very high temperature, please work carefully. -
Page 15: Troubleshooting
9. TROUBLESHOOTING WARNING Be sure to unplug the power cord before repairing. Failure to do so may cause an electric shock. Phenomenon Check Actions The unit does not work Is the power cord or the connection Connect the power cord and connection even when the power is plug disconnected? cord. - Page 16 10. PART NUMBER (continued) SEMS screw M3×6 P2 SEMS screw M3×18 P2 (2) Station Item No. Part No. Part name Specifications B5244 Blade removal plate w/screw B5245 Handpiece holder w/screw qty 2 for HAKKO FT-802 B2419 Power cord/3 core & American plug 120 V USA B2421 Power cord/3 cored wire with no plug...