Related Manuals for LiteOn WP8722
Summary of Contents for LiteOn WP8722
- Page 1 USER’S MANUAL ACCESS POINT MODEL NAME: WP8722, WP8722-BT BRAND: LITE-ON Page 1/10 LITE-ON...
-
Page 2: Table Of Contents
1. PRODUCT DESCRIPTION ......................4 ......................4 RODUCT ELIVERABLES 2. HARDWARE REQUIREMENTS....................4 ..........................4 AIN CHIPSET ....................5 NCLOSURE AND ECHANICAL ..........................6 OUNTING ......................7 NTENNA AND IRELESS ..........................8 THERNET PORT LED I : ..................8 NDICATOR UNCTION EFINITION ...........................8 OWER UPPLY ......................8 ACTORY EFAULT ESET ..........................8 EBUG PORT 3. - Page 3 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
-
Page 4: Product Description
Product Description The product is structured as SOC QCA9563 + Radio QCA9886. One radio offers 802.11n 300Mbps at 2.4GHz and another radio offers 802.11ac 866Mbps at 5GHz. See Figure-01 The product connects to the backbone network through Giga-bit Ethernet interface with 802.3af/at PoE PD which is able to be powered by PoE switch remotely. -
Page 5: Enclosure And Mechanical
- 2× SPI NOR 32M Bytes (Optional) Flash: 128MB NAND Flash (optional, to be charged separately if required) DDR2: 128Mbytes Enclosure and Mechanical The dimension for the product as below: ME Dimension (L x W x D): 150mm × 150mm × 36.25mm ... -
Page 6: Mounting
Figure-01 Reference for ID design Mounting The ID has a Kensington lock hole on the enclosure. Standard mount: Ceiling mount through the recessed ceiling-tile rail mounting adapter to comply with 15mm, 24mm, and 38mm rails. Rubber foot (x2) could be attached for table stand application. Figure-02 Standard mount Page 6/10 LITE-ON... -
Page 7: Antenna And Wireless
Hard flat surface mounting including wall and ceiling mount. 1) Standard, 2 key holes in the central part on the bottom case 2) Optional accessory, separate bracket (to be charged separately if required) Figure-03 Optional premium mounting bracket for hard flat surface mount Antenna and Wireless The product shall deliver 2×2:2 wireless connections on both 2.4~2.4835GHz and 5.15~5.875GHz. -
Page 8: Ethernet Port
Ethernet port 1×10/100/1000 BASE-T Ethernet (RJ-45) port with PoE PD LED Indicator Function Definition: The LED shall be enabled and disabled by software. Please see the table below for detailed definition. 1) Blue: All Radios’ are up and user are connected 2) Orange: One of the Radio are Down 3) Green: All Radios are up 4) Red: No Network or Backhaul... -
Page 9: Rf Capability
(Note, the system image is basing on QCA SDK indicated. Further SDK version changes maintained in software document separately) RF capability Transmite power (Single chain) The table below shows the design target for maximum transmit power per chain @ the different data rates. -
Page 10: Physical And Environmental
VHT20 256QAM @ 5/6 Code Rate VHT40 256QAM @ 3/4 Code Rate VHT40 256QAM @ 5/6 Code Rate VHT80 256QAM @ 3/4 Code Rate VHT80 256QAM @ 5/6 Code Rate Physical and Environmental Power consumption: 12.4W excluding USB (Note, test condition under tthroughput mode: Run IxChariot for 2G upload Mode @11n HT20 MCS0 20dBm and 5G upload Mode @11n HT20 MCS0 18dBm to measure the total power consumption) ...