XCell 148134 Operation Manual page 2

SOLARPANEL 100W
Artikel-Nummer: 148134
operation manual
Thank you for purchasing our product. For your safe use of this product, please read this
manual carefully before use.
INSTRUCTIONS
- Open the buckle of the solar folding bag to take out the internal accessories of
the waterproof bag, and place the solar panel facing the sun at a 45°C angle or
fl at, and the LED indicator of the output power box is on. At this time, the solar
charger starts to work, and the USB port outputs a DC voltage of 5.0V. DC or
Anderson port output voltage> 18.0V.
- This product is not recommended to charge the mobile phone directly. It needs
to be used with a power bank. The power bank can charge mobile phones,
tablets and other electronic products.
- When charging the battery, fi rst connect the output terminal of the solar panel
to the matching DC terminal or wire (pay attention to the correct connection of
the positive and negative poles), the output DC terminal or wire voltage of the
solar panel is 18V (20V at no load), and then connect the DC terminal or wire
to the 12V battery. Note that the positive and negative poles are connected
correctly, and the battery can start charging.
Reminder: The high-voltage output port of this product does not have MPPT
charging protocol and needs to be purchased separately
SCHEMATIC DIAGRAM OF CAR CONNECTION
GB
- The output voltage of the solar charger DC or Anderson is> 18.0V. Use 2-4pcs
solar panels in series to expand the output power to 18.0V-36.0V-72.0V.
Tip: It can only be achieved by purchasing a professional converter and MPPT
controller
- If the product is equipped with MPPT solar controller, you must connect the
battery and then the solar panel fi st, then it will work. Otherwise there is no
display on the controller and it does not work. Before use, please make sure
that the positive and negative poles of are connector together correctly. Tip:
Do not connect or touch the red wire (positive) and black wire (negative)
together during use, which will cause short-term heating or burning.
- The selection of MPPT charging system can increase the charging speed,
solar energy conversion effi ciency, and protect the output state of the solar
charger. No choosing MPPT charging is not ideal.
TIPS
- If there is no professional and technical personnel, please do not change the
circuit or the using method of the product, which may cause the product to be
damaged. Our company is not responsible for it.
- The product is not suitable for low-current charging devices (standard charging
current is below 1OOmA), and it is prone to constantly shutting down and
restarting. Although the USB output port has an identifi cation IC, it cannot be
guaranteed to be compatible with 100% of the devices on the market.
- The input voltage power is low when the solar light is insuffi cient. It may cause
the low-voltage port to have no fast charging. According to the light situation.
It is determined that the charging device will be powered off and other devices
need to be used for charging.
- The combination of solar panel and light and the surface temperature of solar
panel higher than high 50°C will affect the actual output power and effi ciency
of solar products
- When the device is fully charged or due to insuffi cient light intensity, the output
port may be continuously turned on/off. This situation belongs to the normal
working range of the product.
- This product is suitable for outdoor use in the sun, not suitable for rainy days
and indoor charging. Best working hours: 9:00-16:00
PRECAUTIONS
The output voltage power of the solar cell depends on the load working voltage.
- Please do not scratch the surface of the solar panel with sharp objects.
- When using the solar panel to charge the devices, please place the solar panel
facing up in direct sunlight to ensure the best charging effect.
- Please do not use it in rainy days or indoors.
- Put the charger outdoors for emergency charging, and the surface of the
product is waterproof. (The front of the solar panel is not afraid of rain, and the
USB and DC ports are not waterproof to avoid short circuits and affect the
next use)
- Do not use corrosive liquids to wipe the product, scratch the surface of the
battery panel, bend over 45°C, or squeeze and other undesirable actions. It
will cause the output power of the solar charger to decrease.
- If the operation this product or folding product, please handle it gently. The
operation must touch the power generation solar power generation panel, try
to hold the cloth area to operate.
HOW SOLAR PANELS WORK
The solar radiant energy is converted into electric energy through the solar
panel. It uses the photoelectric effect inside the solar panel. When the sun
shines on a kind of semiconductor called the „PN junction" in the solar
panel, light with extremely short wavelengths is easily absorbed inside the
semiconductor and collide with the „valence electrons" in silicon atoms, the
„valence electrons" gain energy to become free electrons and escape the
lattice, thereby generating electron fl ow.
The function of this prod uct is to suppl y power to devices such as mobile
phones, storage batteries, lithium battery packs, and energy storage power
supplies. The device has 4 major charging protection functions: short-c ircuit
protection, charging protection, overload protection, and load identifi cation
function. This is a great help to the life of the rechargeable battery and
maintains the life of the battery. Very suitable for outdoor work, travel or
camping training use.
Please use it in accordance with the manual. Any improper use will cause
problems to the product. We will not be responsible for this. Thank you for your
cooperation and understanding
CERTIFICATE OF CONFORMITY
This product has been strictly inspected during production and is comp liant to
the standard below: UL1310, UL1838, CE, ROHS, FC, PSE
Made in China
energy inside GmbH, Ludwig-Elsbett-Straße 8,
D-97616 Salz, Germany, www.energyinside.de
WEEE-Reg.-Nr. DE 95037264