Subscribe to Our Youtube Channel
Related Manuals for Milestone pro MPHUC-T70WPT4K
Summary of Contents for Milestone pro MPHUC-T70WPT4K
- Page 1 User Manual MPHUC-T70WPT4K 3x1 Wallplate Transmitter Switcher Kit All Rights Reserved Version: MPHUC-T70WPT4K_2023V1.0...
- Page 2 3x1 Wallplate Transmitter Switcher Kit Preface Read this user manual carefully before using the product. Pictures shown in this manual are for reference only. Different models and specifications are subject to real product. This manual is only for operation instruction, please contact the local distributor for maintenance assistance.
- Page 3 3x1 Wallplate Transmitter Switcher Kit SAFETY PRECAUTIONS To ensure the best from the product, please read all instructions carefully before using the device. Save this manual for further reference. Unpack the equipment carefully and save the original box and packing material for ⚫...
-
Page 4: Table Of Contents
3x1 Wallplate Transmitter Switcher Kit Table of Contents 1. Product Introduction ....................1 1.1 Features ......................1 1.2 Package List ...................... 2 2. Specification ....................... 3 2.1 Switcher ......................3 2.2 Receiver ......................4 3. Panel Description ......................5 3.1 Switcher Front Panel ..................5 3.2 Switcher Rear Panel .................. -
Page 5: Product Introduction
3x1 Wallplate Transmitter Switcher Kit 1. Product Introduction Thank you for choosing the MPHUC-T70WPT4K 3x1 Wallplate Transmitter Switcher Kit, which consists of a wallplate transmitter switcher and a receiver. The kit is designed to switch and extend HDMI or USB-C source signal to far-end display device, and the transmission distance is up to 131ft/40m at 4K and 229ft/70m at 1080p video by using a single CATx cable. -
Page 6: Package List
3x1 Wallplate Transmitter Switcher Kit 1.2 Package List 1x Wallplate Transmitter Switcher ⚫ Wallplate Switcher 1x 2-pin Terminal Blocks ⚫ 2x 3-pin Terminal Blocks ⚫ 1x Receiver ⚫ 2x Mounting Ears with 2 Screws ⚫ Receiver 1x 3-pin Terminal Block ⚫... -
Page 7: Specification
3x1 Wallplate Transmitter Switcher Kit 2. Specification 2.1 Switcher Input Input (2) HDMI, (1) USB-C Input Connector (2) Female type A HDMI, (1) Type-C USB HDMI Input Resolution Up to 4K@60Hz 4:4:4 USB-C Input Resolution Up to 4K@30Hz 4:4:4 Output Output (1) HDBT OUT Output Connector... -
Page 8: Receiver
3x1 Wallplate Transmitter Switcher Kit 2.2 Receiver Input Input (1) HDBT Input Connector (1) RJ45 Output Output (1) HDMI Output Connector (1) Type-A female HDMI Control Control port (1) FW, (1) IR IN, (1) IR OUT, (1) RS232, (3) USB IN (1) Micro-USB, (2) 3.5mm jacks, (1) 3-pin terminal block, Control Connector (3) Type-A USB 2.0... -
Page 9: Panel Description
3x1 Wallplate Transmitter Switcher Kit 3. Panel Description 3.1 Switcher Front Panel ① POWER LED: The LED illuminates red when power is applied. ② LINK LED: The LED illuminates green when the switcher is successfully connected to the receiver by a CATx cable. ③... -
Page 10: Switcher Rear Panel
3x1 Wallplate Transmitter Switcher Kit hold it at least 3 seconds to enable auto-switching mode. For more details, please refer to the 6.1 Signal Switching. ⑪ DISPLAY ON/OFF: Press the button to turn on/off the display. For more details, please refer to the 6.2 Display Control. 3.2 Switcher Rear Panel HDBT OUT ①... -
Page 11: Receiver Front And Rear Panel
3x1 Wallplate Transmitter Switcher Kit 3.3 Receiver Front and Rear Panel LINK HDCP ① POWER LED: The LED illuminates green when power is applied. ② FW: Micro-USB port for firmware upgrade. ③ IR IN: Connects to IR receiver to control far-end source device by IR pass-through. ④... -
Page 12: System Connection
3x1 Wallplate Transmitter Switcher Kit 4. System Connection The following diagram illustrates typical input and output connection that can be utilized with the extender: Transmitter Receiver HDBT OUT LINK HDCP Projector Receiver IR Emitter Keyboard Laptop MacBook Remote HDMI: USB-C: HDBaseT: IR Control: USB Control:... - Page 13 3x1 Wallplate Transmitter Switcher Kit This allows you to control a display (TV) at the source device's end, where the switcher is. For example, you have a projector at the receiver's end and you want to turn it on and control it at the source device's end. Plug the IR emitter into the IR OUT port in the receiver.
-
Page 14: Button Control
3x1 Wallplate Transmitter Switcher Kit 6. Button Control 6.1 Signal Switching 1) Press the SOURCE AUTO button to switch to next source device, and then the corresponding input LED will turn green. 2) Press and hold the SOURCE AUTO button at least 3 seconds to enable auto switching mode, and it abides by the following principles: The switcher will switch to the first available active input starting at HDMI IN 1>... -
Page 15: Rs232 Control
3x1 Wallplate Transmitter Switcher Kit 7. RS232 Control 7.1 RS232 Connection According the RS232 control mode, there are three types of RS232 connection for different application. 1) When only control the switcher, please connect a control device (e.g. PC) to the RS232 port of the switcher, the connection diagram shown as below: Transmitter Receiver... -
Page 16: Rs232 Commands
3x1 Wallplate Transmitter Switcher Kit 3) If the switcher needs to be controlled by receiver end, the control device (e.g. PC) can be connected to the RS232 port of the receiver, the connection diagram shown as below: Transmitter Receiver HDBT OUT LINK HDCP 7.2 RS232 Commands... -
Page 17: Source Switching
3x1 Wallplate Transmitter Switcher Kit Command Example Command Description and Feedback C - USB-C Set the RS232 baud rate. PARAM = 1 ~ 5 >SetRS232Baudrate 1 1 - 115200 >SetRS232Baudrate 2 - 57600 PARAM 3 - 38400 <RS232Baudrate 4 - 19200 115200 5 - 9600 <RS232Baudrate... - Page 18 3x1 Wallplate Transmitter Switcher Kit Command Example Command Description and Feedback When detecting video input signal or not detecting any video signal, the switcher will automatically send the corresponding CEC command to control the display device. <AutoCec True PARAM = EN, Dis EN - Enable (Default) Dis - Disable Get the function setting status of...
-
Page 19: Edid Management
3x1 Wallplate Transmitter Switcher Kit Command Example Command Description and Feedback Set the number of times to send the >SetOffMsgLoopCnt 1 >SetOffMsgLoopCnt DISPLAY OFF RS232 command. PARAM <OffMsgLoopCnt 1 PARAM=1 ~ 2 >GetOffMsgLoopCnt Set the number of times to send the >GetOffMsgLoopCnt DISPLAY OFF RS232 command. -
Page 20: Hdcp Mode
3x1 Wallplate Transmitter Switcher Kit Command Example Command Description and Feedback 0 - Bypass 1 - 1920x1080@60 8bit Stereo 2 - 1920x1080@60 8bit High Definition Audio 3 - 3840x2160@30Hz 8bit Stereo Audio 4 - 3840x2160@30Hz Deep Color High Definition Audio 5 - 3840x2160@60Hz Deep Color Stereo Audio 6 - 3840x2160@60 Deep Color High... -
Page 21: Third-Party Device Control
3x1 Wallplate Transmitter Switcher Kit 7.2.6 Third-party Device Control Command Example Command Description and Feedback >SetPowerOnSendCh ar_5:1234 Send the ASCII command "XXXX" to the remote third-party device while the switcher is powered on. PARAM = 1~7. Represents the baud rate of the third-party device. -
Page 22: Button User-Defined
3x1 Wallplate Transmitter Switcher Kit 8. Button User-defined Press the DISPLAY ON/OFF button can turn on/off the display. If the incompatible display device needs to be used, the DISPLAY ON/OFF button can be programed by IR learning feature or RS232 command. IR learning feature: ⚫... - Page 23 3x1 Wallplate Transmitter Switcher Kit Command Example Command Description and Feedback >SetPowerOnSendHe Set the HEX RS232 command "XX XX" to be x_5:30 31 32 33 sent to the third-party device (e.g. projector) when the DISPLAY ON button has been pressed. >SetPowerOnSendHex_ PARAM = 1~7.
-
Page 24: Firmware Upgrade
3x1 Wallplate Transmitter Switcher Kit 9. Firmware Upgrade Please follow the below steps to upgrade firmware of switcher or receiver by the Micro- USB port: 1) Prepare the latest upgrade file (.bin) of switcher or receiver and rename it as “FW_MERG.bin”...
Need help?
Do you have a question about the MPHUC-T70WPT4K and is the answer not in the manual?
Questions and answers