Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Spectra Manuals
  4. Projection Screen
  5. Vantage UST
  6. Instruction manual

Spectra Vantage UST Instruction Manual

Hide thumbs

Advertisement

Quick Links

Download this manual

Advertisement

loading
Need help?

Need help?

Do you have a question about the Vantage UST and is the answer not in the manual?

Questions and answers

Summary of Contents for Spectra Vantage UST

  • Page 2 Hardware & Parts Included Parts not shown to scale Make sure to clean the area of any dirt, debris or other objects prior to assembly. The screen surface is very delicate. Inner & Outer Frame Assembly Left Short Horizontal Right Short Horizontal Long Vertical Black I-Shaped Inner Frame...

  • Page 3: Mounting Parts

    † Tension Springs Included The number of black and heavy silver tension springs varies based on the size of your Spectra Vantage. Please use the table below as a reference for the number of springs included with your unit. SIZE SPRINGS NEEDED SPARE SPRINGS (APPR.)
  • Page 4 Layout the inner pieces in the correct position On a clean flat surface, lay out the inner frame pieces in the correct position. The screw holes in the frame pieces should be facing upward. Assembling the inner frame Put in 1 short screw (D) loosely to Position the black I-shaped connector (C) so the hold the connector in place.
  • Page 5 Assembling the inner frame (cont.) Repeat on both ends of both vertical frame pieces (B). Once the frame is aligned Insert the inner L-shaped at all 4 corners, put in 2 short Connect both vertical inner frame connector (E) into the slot of the screws (D) loosely to hold the pieces (B) with both horizontal vertical inner frame piece (B).
  • Page 6 Connecting the inner frame to the screen surface Carefully take the screen surface (H) out of the cardboard tube. Roll the screen out flat so that the white protective fabric is between the floor and the screen. Be sure not to bend or crease the surface as doing so could cause irreparable There may be some ripples in the surface,...
  • Page 7 Connecting the inner frame to the screen surface (cont.) Repeat this so all tension rods Slide tension rod into the are in their sleeves. The rods sleeves at the edges of the should not be overlapping. screen surface (H). 3.10 3.11 To attach the surface to the frame, start from position 1A in the bottom left corner, and then follow the...
  • Page 8 Assembling the outer frame Slide the steel I-shaped connector Line up the left horizontal piece (M1) and right horizontal piece (M2) (O) into the slot on the left of the outer frame with the I-shaped connector (O). horizontal piece (M1). Screw the tiny hex-screws (P) Slide the other side of I-shaped Repeat with the other horizontal...
  • Page 9 Assembling the outer frame (cont.) 4.10 Slide the outer L-shaped connector (Q) into the When assembled it slot at the bottom of the should look like this. vertical outer frame (N). Repeat for all Loosely screw the 4 corners. connector into place with the hex-screws (P).
  • Page 10 Assembling the outer frame (cont.) 4.15 Secure the outer frame and inner frame together using the tensioning clips (R) in these locations. 4.16 4.17 4.18 Stretch the tensioning clip and hook it onto the lip of the inner frame. Your projector screen is now assembled and ready to be...

  • Page 11: Mounting The Screen

    Mounting The Screen Please follow the guidelines and handle your screen with care throughout the installation process. Things You’ll Need: Tape Measure Drill Screwdriver Someone to assist with Pencil Ladder or Stepstool hanging the screen Turn on your ultra short throw projector and shine a bright image onto the wall Adjust the placement of the projector so that the projected image is level, squared off and the top is the same width as the...
  • Page 12 If the bracket is not being installed into a stud, use the Drill holes in the wall in the marked locations. yellow drywall anchors (T). Attach the brackets to the wall using the mounting screws (U). Repeat this on the top right side of the projected image. Assemble the magnetic spacer component together (V1,V2,V3,V4) From the bottom left corner of the projected image measure 6 inches Drill a hole and screw the magnetic...
  • Page 13 Turn off the projector and move it out of the way so you don’t accidentally damage it or the screen. You’re now ready to mount the screen on the wall. Have each person wear a glove (W) on the hand Hang the screen with the assistance of another that will hold up the bottom of the screen to prevent person.
  • Page 14 To make it easier to adjust, have your helper lift that side of the screen off of the bracket. Adjust the screen as needed. Your screen is now securely in place and you’re ready to enjoy a cinematic experience on your new Spectra Projection screen.
  • Page 15 Introducing the Spectra Slider Pairs perfectly with your new Spectra Vantage UST With the new Spectra Slider, you can perfectly position your projector to achieve your desired image size, without the need for expensive, specialized UST furniture. With the Spectra Slider’s telescopic design, you can easily adjust your projector’s position for optimal...