Matsui 1408T Quick Start Manual

MATSUI 1408T
Matrix
Item
Adjustments ................................................................................................. 1408R
Deflection CRT Diagram ............................................................................. 1408R
Scart Diagram .............................................................................................. 1408R
Waveforms ................................................................................................... 1408R

Recommended Safety Parts

Item Part No. Description
R408 R6558A1R5J R, FUSE
R429 R655812R7J R, FUSE
R448 R5Y2CD822J R, CEMENT
R501 R002T2155J RC
R502 R3X181R33J R, METAL
R503 R5Y2CE5R6J R, CEMENT
R504 R63584681J R, FUSE
R513 R3X28B224J R, METAL
R516 R3X28B150J R, METAL OXIDE
R524 R3X28B3R3J R, METAL
R3K28B3R3J R, METAL
R803 R3X18A153J R, METAL OXIDE
R3U18A153J R, METAL
R805 R3X18A153J R, METAL OXIDE
R3U18A153J R, METAL
R807 R3X18A153J R, METAL OXIDE
R3U18A153J R, METAL
C501 P2222B224K CMP
C525 CB3930MH3M CC
D407 D28T10ELS6 DIODE, RECTIFIER
D410 D28T10ELS6 DIODE, RECTIFIER
D501 D2BTRM11C0 DIODE, RECTIFIER
D502 D2BTRM11C0 DIODE, RECTIFIER
D503 D2BTRM11C0 DIODE, RECTIFIER
D504 D2BTRM11C0 DIODE, RECTIFIER
D510 D28I15DF60 DIODE, SILICON
D511 D28T10ELS6 DIODE, RECTIFIER
D512 D28T10ELS6 DIODE, RECTIFIER
D515 D28I15DF60 DIODE, SILICON
IC401 I03SD78400 IC
IC402 I1KA978050 IC
IC501 I2BT056520 IC
IC502 I1KA978050 IC
Q401 TDUQ025990 TRANSISTOR, SILICON
Q503 TA3T1371A0 TRANSISTOR, SILICON
Q801 TC3T034680 TRANSISTOR, SILICON
Q802 TC3T034680 TRANSISTOR, SILICON
Q803 TC3T034680 TRANSISTOR, SILICON
L501 029K000001 COIL, LINE FILTER
L502 029A000002 COIL, LINE FILTER AC
L503 028R140027 COIL, DEGAUSS
T501 048135032W TRANSFORMER, SWITCH
J801 066X120014 SOCKET, CRT HP
SW501 0530205002 SWITCH
CD501 1206635818 CORD, AC
F501 0808T04002 FUSE
F502 0808T01002 FUSE
! FB401 043214029F TRANSFORMER, FLYBACK
ICP501 083PC01002 MICRO FUSE
V801 098P140479 CRT
Table 1

Service Mode List

See Model Book
This unit provided with the following SERVICE
MODES so you can repair, examine and adjust
6
easily.
6
6
To enter the Service Mode, press both set key
6
and remote control key for more than 2 seconds.

CONFIRMATION OF USING HOURS

POWER ON total hours can be checked on the
screen. Total hours are displayed in 16 system
of notation.
1.5 OHM 2W
2.7 OHM 1W
1. Set the VOLUME to minimum.
8.2K OHM 5W
2. Press both VOL. DOWN button on the set
1.5M OHM 1/2W
0.33 OHM 1W and Channel button (6) on the remote control
5.6 OHM 7W
for more than 2 seconds.
680 OHM 1/4W
220K OHM 3W 3. After the confirmation of using hours, turn off
15 OHM 3W
the power.
3.3 OHM 3W or
3.3 OHM 3W
15K OHM 2W or
15K OHM 2W
15K OHM 2W or
15K OHM 2W
15K OHM 2W or
15K OHM 2W
0.22 UF 250V AC MMCA
0.0022UF 250V
10ELS6TA1B2
10ELS6TA1B2
RM11C

NOTE FOR THE REPLACING OF MEMORY IC

RM11C
RM11C
RM11C If a service repair is undertaken where it has
15DF6-FC
been required to change the MEMORY IC, the
10ELS6TA1B2
following steps should be taken to ensure
10ELS6TA1B2
15DF6-FC
correct data settings while making reference to
LA7840
TABLE 1.
KIA7805PI
STR-F5652
KIA7805PI
NOTE: No need the setting for after INI 10.
2SD2599
2SA1371(D,E)-AE
2SC3468(D,E)-AE
1. Enter DATA SET mode by setting VOLUME to
2SC3468(D,E)-AE
minimum.
2SC3468(D,E)-AE
RB-20871
2. Press both VOL. DOWN button on the set
FK0B160MH14
and Channel button (6) on the remote control
8R140027
8135032W
for more than 2 seconds.
S3200-010501
3. ADDRESS and DATA should appear as Fig 1.
SDDFC30400
1206635818 4. ADDRESS is now selected and should "blink".
218004
Using the SET + or - keys on the remote, step
218001.
through the ADDRESS until required AD-
3214029F
251001
DRESS to be changed is reached.
A34AGT13*78
5. Press ENTER to select DATA. When DATA is
selected, it will "blink".
6. Again, step through the DATA using SET + or
- until required DATA value has been se-
lected.
7. Pressing ENTER will take you back to
ADDRESS for further selection if necessary.
8. Repeat steps 4 to 7 until all data has been
checked.
9. When satisfied correct DATA has been
entered, turn POWER off (return to STANDBY
MODE) to finish DATA input.
The unit will now have the correct DATA for the
new MEMORY IC.
This area is intentionally left blank.