GRAPHTEC GS-TH User Manual

GS-TH
Temperature / Humidity Sensor
USER'S MANUAL
Thank you very much for buying this GRAPHTEC product.
This product is a measurement sensor (hereafter "module") that
connects to the GL100-N/GL100-WL.
These directions describe preparations and cautions before
measurement.
To ensure safety, please read the operation instructions, etc.
For details on the warnings and how to handle this module, please
read Quick Start Guide or USER'S MANUAL included on the
CD-ROM (included in the GL100 packaging).
Confirmations ot the exterior
After opening the package, please confirm that there are no
problems (scratches and dirt) on the exterior before use.
Confirmation of the attached items.
•
User's manual (this book): 1
If by any chance faults are found, please contact the store where you bought
the item.
* Please note that items mentioned in this book may change without prior
notice.

1 Part Names

This section describes the name and function of each part.
1. Hook portion
2. Connector
GL100
1. Hokk portion ...................... Used to mount to a wall
2. Connector .......................... Used to connect to the connector on the
GL100 module
3. Cable packinge ................ This packing is used when connecting the connector.
Attaching just this module
to the wall, etc. will damage
the connector cable.
Always connect to the
GL100.
The temperature sensor measures the change in capacitance
of the conductivity caused by moisture absorption.
Therefore, dust, fumes and other organic compound may
affect measurements. Usage in an environment with a large
quantity of these substances floating about will cause large
measurement deviations.
After connecting the GL100 to modules or sensors, please always check/set the
time and date.
GS-TH-UM-151
For GL100
3. Cable packing
Wall mounting
hook
2 Messung

1. Power supply

(Refer to Quick Start Guide or USER'S MANUAL.)
Connect this module while power is being supplied to the GL100 by a battery or USB cable.

2. Start-up and operation

(1) Screen display menu flow

After power-on, the GL100 is ready for operation by holding down [MENU] key.
When the module is connected, "Module Type Recognition" screen is displayed.
When the module is not connected, "Module Unconnected State" screen is
displayed.
Operate in accordance with the displayed instructions.
Module unconnected state
<Operation>
Connect the module.
Recognition of module types
Standby state
<Operation>
Press [ENTER] key.
Module start-up

(2) Free-running screen

Hold down the [QUIT] key (approx. three seconds) to
put the module into standby state.
When running on batteries, the module will
automatically go into standby state after three
minutes of no operation.
Press the [ENTER] key while in standby state to
return to the free-running screen.
3. Setting
(1) Screen operation
Item selecting screen
Press the [MENU] key on the free-running screen to go to the setting screen.
<How to set>
Select the item with the directional keys (
Numerical entry screen
<How to set>
Numbers can be inputted by increasing or decreasing the value with the

(2) AMP setting

The accumulated temperature can be set for the set temperature.
AMP Input setting
Mode
REF. TEMP

(3) DATA setting

Set the Sampling and Capture Mode those will be recorded to the data
recording media.
The recorded data's size will be displayed in the information for the SD card
being recorded to. Please take note of it.
DATA recording condition setting
Sampling
Capture MODE
Capture DIST

(4) TRIGGER setting

Select the conditions for beginning data recording after measurement starts.
Off : Pressing the [START/STOP] key on this module will start/stop recording.
Start : The recording will start with the trigger source conditions after
pressing the [START/STOP] key.
The recording will stop after pressing the [START/STOP key.
Stop : The recording will start after pressing the [START/STOP] key and
will be stopped with the trigger source conditions.
TRIGGER capture condition settings
TRIG setting
TRIG Source
) and press the [ENTER] key.
If the submenu shows then there
are selections in those directions.
and keys.
REF. TEMP, REF. TEMP
Value setting
500 ms, 1, 2, 5, 10, 20, 30 s,
1, 2, 5, 10, 20, 30, 60min
CONT, 1 Hour, 24 Hour
Memory, SD card
Off, Start, Stop
Off
Alarm
Date Date, Time