Sonicsmith ConVertor E1 User Manual

Sonicsmith ConVertor E1 User Manual

Advertisement

A u d i o C o n t r o l l e d S y n t h e s i z e r
P SHIFT
User Guide
SYNTH
-
+
C
Q
Thank you for pre-ordering the ConVertor E1.
PITCH
FM IN
The ConVertor will convert an analog monophonic audio signal
ENV
GATE
into its Pitch, ENV and GATE Control Voltages, DC signals to control
external analog synths. It also provides its own internal digital
GATE
ENV
synth that is always in tune. It can work by itself with external
A-GAIN
synths or act as its own synth. You can also expand it via a MIDVer-
-
+
tor E1 adding sustain pedal, MIDI i/o, arpeggiation and centralized
FLT
PRE OUT
control for up to 7 ConVertors in parallel. Check periodically for
HI Z
new firmware on our product page: sonicsmith.com/products.
-50
-40
-30
-20
-10
+4
Feel free to write us with any feedback, question or concern at:
info@sonicsmith.com
TRS
AUDIO IN
Sonicsmith 2023

2) Preamp section buttons

Connect a TS or TRS Mic/Inst./Line 1/4" plug into the audio input
HI Z
If you play a pickup inst. press the
FLT
To toggle between
Press
analog input HPF frequencies:
ENV
A-GAIN
GATE
Press
A-GAIN
loudly, brifly, during 2.5 seconds. After 2.5 seconds, the gain
-
+
FLT
PRE OUT
will be set and the meter will go back to showing input levels.
The gate will not effect the PRE OUT signal. Press the GATE
HI Z
knob and dial to change the
-50
-40
-30
-20
-10
+4
red) and initiating another 2.5 second count. The ConVertor
E1 will remember all preamp/comp settings after a restart.
The gain can amplify the input up to +54db. If you turn the
GATE encoder and see the meters change value in green then
TRS
AUDIO IN
you are changing the gate's threshold (see square #3).
Sonicsmith 2023
Firmware 1.0
Aug 2023
ConVertor E1 User Guide - Firmware 1.0
LOW Z: 50 kOhm
HI Z: 2M Ohm
RED
25 Hz
75 Hz
150 Hz
GREEN
RED
To activate Auto-GAIN detection, play
gain manually
(metered in
ConVertor E1 User Guide - Firmware 1.0

1) Connecting and powering

To use the ConVertor E1 you need to supply your own 12V powered Eurorack
case with 12HP (6cm) available space, one available power connection and
about 90 mA of current available. Connect the power cable to the back, place
and screw the panel to the rack using the two included standard M3 screws.
Avoid exposing it to sun, fulids or unchecked physical abuse/shocks.
"Sonicsmith bus" 4 pin header
to MIDVertor E1 (optional)
FM CV in
Mic/Inst/line input
Balanced/unbalanced
There is no 48V phantom power. Please
stronger than +4dBu or CV signals into the
outputs of this device are very loud potentially around 10V scale. Always test a
signal's loudness before patching it with speakers or headphones on.
Sonicsmith 2023
3) The two encoders: GATE & P SHIFT
P SHIFT
P SHIFT
Turn the
SYNTH & the PITCH CV outputs up to
SYNTH
-
+
the
P SHIFT knob to bypass the shift back to
PITCH
FM IN
again to come back to the shift.
FM IN
relative to the
ENV
GATE
giating the pitch from a sequencer 1/V per octave output,
patched into it.
GATE
-
+
GATE
Turn the
knob to increase/decrease the gate's threshold in 1dB incre-
threshold
ments. Default GATE
by shutting the ENV CV out to 0V and the SYNTH OUT audio off. PRE OUT is analog
copy of the same signal going to the ADC. Connect the pre-out minijack TS to an
+18dBu-capable destination like Eurorack gear. The gate's threshold can vary
between -6dbFS to -65dbFS.
Sonicsmith 2023
Synth out
A u d i o C o n t r o l l e d S y n t h e s i z e r
P SHIFT
SYNTH
-
+
C
Q
PITCH
FM IN
Pitch
CV
ENV
GATE
ENV
CV
GATE
ENV
A-GAIN
-
+
GATE
CV
FLT
PRE OUT
HI Z
-50
-40
-30
-20
-10
+4
Preamp out
TRS
AUDIO IN
Avoid
patching any audio signal
audio input.
The audio & CV
ConVertor E1 User Guide - Firmware 1.0
knob to shift the DCO's semi-tones
-2 - +2
octaves. Press on
unison.
The resulting pitch shift is
1V/oct CV input so you can try arpeg-
is
-35 dBFS
and will effect the ENV CV output
ConVertor E1 User Guide - Firmware 1.0
Press it

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ConVertor E1 and is the answer not in the manual?

Questions and answers

Summary of Contents for Sonicsmith ConVertor E1

  • Page 1 1) Connecting and powering To use the ConVertor E1 you need to supply your own 12V powered Eurorack A u d i o C o n t r o l l e d S y n t h e s i z e r...
  • Page 2 FAT 32 file system and not any bigger than 32 GB. After you insert ConVertor E1 synth will stay in unison. We can modulate its the SD card at the back of the module, power the device off, hold frequency within 8 octave range.

Table of Contents