1. Manuals
  2. Brands
  3. NEAT Electronics Manuals
  4. Smoke Alarm
  5. SMOKE
  6. User manual

NEAT Electronics SMOKE User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SMOKE
User Manual
NE41 06004-02 v2.0

Advertisement

Table of Contents
loading

Summary of Contents for NEAT Electronics SMOKE

  • Page 1 SMOKE User Manual NE41 06004-02 v2.0...
  • Page 2 ③ This User Manual © Copyright 2015 NEAT Electronics AB We, NEAT Electronics AB, Varuvägen 2, 246 42 Löddeköpinge, SWE- DEN, hereby declare under our sole responsibility that this product, Document number: NE41 06004-02 v2.0 SMOKE, is in conformity with the directives:1999/5/EC, 2006/95/EC,...
  • Page 3 About SMOKE SMOKE is a smoke detector with a radio adapter board and can be used with all NEAT radio receivers and is inteded to be used in warden facilities or in households. This user manual is valid for SMOKE with ADAPTER board revision 2 or later, see “2 Adapter board”.

  • Page 4: Adapter Board

    0.5 m when testing. Press the SMOKE test button (B1), at least 2 s, the detector LED should be blinking and a loud tone should sound. Then the smoke detector is working properly.

  • Page 5: Button Operation

    Stand by state. The unit can be returned prematurely to Stand by state by pressing short- ly on button S1 when in Programming state. SMOKE User Manual NE41 06004-02 v2.0 5 of 16...

  • Page 6: Operation Modes

    Individual group mode Picture 3. SMOKE operation modes By default SMOKE is configured as Stand Alone. The first time SMOKE is configured as a linked unit it automatically enters Individual group Mode. When a linked unit is in either of the two linked modes, it’s possible to toggle between the modes, see “9 Toggle between linked modes”.

  • Page 7: Standalone Mode

    All SMOKEs must be programmed to different radio positions. Stand Alone mode When a SMOKE is operating in Stand Alone mode, it operates as a single unit with no interconnection between other SMOKEs and communicates directy with the radio receiver, e.g a Care Phone NEO or a portable tranceiver TREX2G.

  • Page 8: Smoke Alarm

    SMOKE must be added individually to that radio receiver. A SMOKE in Stand Alone mode will NOT listen to any radio transmissions. This mode is the preferred mode when only one SMOKE is used, e.g. in a single house hold. Smoke alarm In the event of fire the SMOKE starts sounding with the acoustical indica- tion and the unit’s Test button LED blinks red and a Smoke alarm is sent...

  • Page 9: Group Mode

    Picture 5. SMOKE units in Individual Group mode When smoke is detected, e.g. by the slave sounds with the acousti- cal signal, the LED is flashing red and a smoke alarm is sent to the radio receiver (a Care Phone NEO).
  • Page 10 Master and receiver can be extended with REPO and/or REPO+ (optional accessory). Example of star pattern Look at the setup in Picture 6; “SMOKE units in a Star pattern setup” above. When smoke is detected, e.g. by Slave the slave sounds with the acoustical signal, the LED is flashing red and a smoke alarm is sent.

  • Page 11: Resetting Alarms

    REPO and/or REPO+ (optional accessory), see “7.1.1 Star pattern” on page 10. Example of chain pattern Look at the setup in Picture 7; “SMOKE in a Chain pattern set up.” above. When smoke is detected, e.g. by Slave the slave sounds with the acoustical signal, the LED is flashing red and a smoke alarm is sent.

  • Page 12: Resetting An Alarm

    Resetting an alarm Smoke alarms can be reset on two levels and is done by pressing the unit’s Test button (B1). The levels are : • Global reset, see below. • Local mute, see below. For both resets, the acoustical indication goes silent.
  • Page 13 • The Unliked unit flashes rapidly 8 times and the goes into Stand by state. When unlinking the unit it automatically stores the last linked operation mode, so in the event of re-linking the unit, the last linked mode is used. SMOKE User Manual NE41 06004-02 v2.0 13 of 16...
  • Page 14 • Do not clean the device with harsh chemicals, solvents or other corrosive substances. 11.4 Recycling • Dispose of properly. The worn out product must be returned to a recycling facility for proper disposal or returned to NEAT Electronics. 14 of 16 SMOKE User Manual NE41 06004-02 v2.0...

  • Page 15: Technical Data

    <6 m in height Action indication Red LED Signal tone >85 dB(A) @ 3 m Satisfy regulation ISO 12239 Drill hole distance 28 mm <> 56 mm Case/colour ABS/White Table 8. SMOKE technical data SMOKE User Manual NE41 06004-02 v2.0 15 of 16...
  • Page 16 NEAT Electronics AB www.neat-group.com/se...

Table of Contents