Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Orava BN-30
- Page 1 Electric knife sharpener BN-30 Instruction manual BN-30...
- Page 2 Do not use the tool to sharpen the blade of other types of tools/tools or tools. ORAVA Electrical Appliances are manufactured in accordance with the state of the art and recognized safety-technical rules. Nevertheless, the use or use contrary to designation may result in the risk of injury to or endangering the life of the user or third person, damage to the device and other material values.
- Page 3 • This appliance is intended, in addition to domestic use, for the following uses: - in shops, offices and other similar work environments; - in economic buildings; - in hotels, motels and other residential environments; - in bed and breakfast establishments. •...
- Page 4 1.3 Electrical safety • Before connecting the appliance to the power supply for the first time, make sure that the voltage on the appliance label corresponds to that of the household electrical outlet. • The electric appliance is designed to power from 1/N/PE ~ 230 V 50 Hz. •...
- Page 5 • To avoid electrical shock, plug the power cables into properly grounded electrical sockets. If the device is equipped with a 3-pole plug, do not use adapters that do not have a grounding element or remove the grounding element from the plug or adapter.
- Page 6 1.5 Cleaning, maintenance and repairs • Observe the normal user cleaning and maintenance of the appliance in the recommended way. Do not use solvents or harsh cleaners for cleaning. Pollution and visible stains from finger contact, respectively. The hands can be cleaned using detergent detergents specially designed to clean household appliances.
- Page 7 2. Special Safety Instructions. Read carefully! Electrical equipment is designed and manufactured in such a way as to allow for safe operation and use by persons without a professional qualification. Despite all the measures that have been carried out by the manufacturer for safe use, handling and use, entails certain residual risks and associated potential hazards.
- Page 8 Check/Startup • Carefully clean the machine before commissioning it, following the instructions in the „Startup“ section.„Cleaning and maintenance“. • Never clean the machine (its drive unit with electrical parts and controls) and the power cord with the plug in a way (under running water) that may cause the liquid to flow into the device.
- Page 9 Operation/Supervision Please note! • The device is intended for grinding the blade edge. As the operator is handling a very sharp knife, always work with care and caution. • In case of careless handling: There is a risk of tearing or puncture of your fingers/hands! •...
- Page 10 Warning! • After switching off the drive, the drive of the rotating parts will recharge for a certain amount of time. Always wait for the rotating parts to stop completely before handling the device. There is a risk of serious injury! •...
-
Page 11: Parts Descriptions
Parts descriptions 1 hand grinder 2 electric grinder/grooves for knife blade 3 power switch 0/I 4 power cord Before first use Do not plug the appliance into the mains during preparation. Unpack and remove all packaging material from it. To remove any dirt that may have occurred during the packing process, clean it with a dry cloth that does not release the fibers. -
Page 12: Preparation And Operation
Preparation and operation Location Disconnect the appliance from the power supply before locating it. Then lay it on and press it against a flat, firm surface so that the suction cups cling to the surface and the device firmly in place. For better adhesion, we recommend that the suction cups be slightly moistened before placement. -
Page 13: Cleaning And Maintenance
Notes • Always pull the knife with a uniform motion out, not back or back and forth - the result of the sharpening would be uneven. Never insert the tip of the knife into the groove and do not press it against the bottom! •... -
Page 14: Technical Specifications
Technical specifications Power supply: 230 V~ 50 Hz Power consumption: 10 W Protection Class: II (Protection against electric shock the current is secured by double insulation) Dimensions (W x H x D): 21 x 7,8 x 7,5 cm Weight: 0,6 kg Noise: 70 dB (A) The declared noise emission of this appliance is 70 dB (A), which is the...
Need help?
Do you have a question about the BN-30 and is the answer not in the manual?
Questions and answers