1. Manuals
  2. Brands
  3. IHIMER Manuals
  4. Excavators
  5. 9VXE
  6. Original instructions manual

IHIMER 9VXE Original Instructions Manual

Mini-excavator
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
EN
EN
EN
EN
operating instructions
operating instructions
operating instructions
operating instructions
mini-excavator 9VXE
serial numbers from n°:
EA09*0010
06/12 - - - - R00
06/12
R00
06/12
06/12
R00
R00
cod. 2032807005
(Original instructions)
ihimer.com

Advertisement

Table of Contents
loading

Summary of Contents for IHIMER 9VXE

  • Page 1 (Original instructions) operating instructions operating instructions operating instructions operating instructions mini-excavator 9VXE serial numbers from n°: EA09*0010 06/12 06/12 - - - - R00 06/12 06/12 cod. 2032807005 ihimer.com...

  • Page 3: Table Of Contents

    LIFTING THE MACHINE ·································································································· 2-37 MAINTENANCE ························································································································ 3-1 PERIODIC REPLACEMENT OF THE IMPORTANT PARTS ·············································· 3-1 MAINTENANCE INTERVALS ····························································································· 3-2 RECOMMENDED LUBRICATION TABLE ·········································································· 3-5 LUBRICATE THE GREASE································································································ 3-6 MAINTENANCE OF BUCKET ···························································································· 3-9 CRAWLER SHOE············································································································· 3-10 TRAVEL REDUCTION GEAR··························································································· 3-13 9VXE EN...
  • Page 4 HANDLING IN COLD WEATHER ····················································································· 3-37 LONG TERM STORAGE ·································································································· 3-38 SPECIFICATIONS ···················································································································· 4-1 SPEED AND GRADEABILITY ···························································································· 4-1 ENGINE······························································································································ 4-1 MASS ································································································································· 4-1 CAPACITY·························································································································· 4-1 BUCKET ····························································································································· 4-2 DIMENSIONS····················································································································· 4-3 WORKING RANGE ············································································································ 4-4 WORKING RANGE FOR OFFSET DIGGING····································································· 4-5 9VXE EN...

  • Page 5: Foreword

    If you hand over this machine to any third party, this manual should also be handed over to it. The specifications of the machine may be improved and differ from descriptions of this manual. Please contact our dealer if you have some problems or questions. 9VXE EN...

  • Page 6: Machine Number

    FOREWORD MACHINE NUMBER The machine No. and engine No. are marked at the positions shown below. MODEL 9VX3 MODELL 9VXE SERIAL No. SERIAL NO. WB-C010010 MODEL 2TNV70-PIK MODELL 2TNV70-PIKX ENGINE ENGINE NO. SERIAL No. WB-C010020 9VXE EN...

  • Page 7: Machine Direction

    The front, rear, right and left directions of the machine are determined based on the orientation when the driver is seated on the operator seat with the blade frontward, as shown below. Front Blade Right Left Rear WB-C010030 9VXE EN...
  • Page 8 FOREWORD This page is intentionally left blank 9VXE EN...

  • Page 9: Safety

    This manual describes the basic safety instructions to be observed in daily operation, inspection and maintenance of the machine. Observe these instructions carefully for safety. Check the safety with great care for any other matters not described in this manual. 9VXE EN...
  • Page 10 9VXE EN...

  • Page 11: Safety Information

    It is the owner or user of the machine who is responsible for always paying attention to operate the machine, as well as reading and understanding this manual enough to obtain the essential knowledge and skills fundamental to correct machine operation. 9VXE ENG...

  • Page 12: Safety Precautions

    Watch for underground utilities Mark the location of underground utilities such as gas lines, sewers, and power lines before any digging operations. If necessary, the utilities should be temporarily discontinued. WC-C100620 9VXE ENG...
  • Page 13 If the engine is started from a position other than sitting in the operator's seat, there is the danger that the machine starts moving suddenly. Start the engine only after carrying out checks while sitting in the operator's seat. 9VXE ENG...
  • Page 14 Keep Out Keep Out Prevent accidents while moving Always sound the horn to signal others nearby that you are moving the machine. Check that no one is within the working area of the machine before attempting to move it. 9VXE ENG...
  • Page 15 Always observe the bucket and load Always watch the moving bucket or load carefully. Moving bucket or load without care may cause injury to personnel or materials. If you have to look away from it, stop the machine. 9VXE ENG...
  • Page 16 Do not dig at the base of a cliff If you dig at the base of a cliff, it may collapse or stones may drop, causing a danger. Do not dig a cliff. 9VXE ENG...
  • Page 17 Do not lean out of the window, enter between the attachment and cylinder or put your hand or arm between them. If the attachment moves, you may be caught by the attachment, resulting in serious injury or death. 9VXE ENG...
  • Page 18 • Keep the bucket at as low position as 20 to 30 cm from the ground and travel the machine at low speed when traveling on a slope. • Lower the bucket onto the ground and stop traveling if the machine becomes unstable. 9VXE ENG...
  • Page 19 Never load or unload the machine by jacking up the attachment. Otherwise, the machine may fall down. Precautions at transportation Apply stoppers in front of and behind the crawlers. Apply wire ropes to the machine body and attachment and fix them firmly to the load carrying platform. 9VXE ENG...
  • Page 20 Lower the bucket onto the ground and stop the engine to prevent an accident of being crushed or caught by the machine. Keep in good contact with the operator if it is necessary to perform maintenance of the moving machine. 9VXE ENG 1-10...
  • Page 21 Always perform maintenance with the engine shut off. Be careful with hot engine Never touch the engine or muffler right after the machine is stopped. It is very hot and causes burns. 9VXE ENG 1-11...
  • Page 22 Prevent fire or explosions Keep away fuel, lubricant and coolant from any fire or heat. Most of them are very flammable. Never place flammable materials or objects close to fire or heat. WC-C300020 9VXE ENG 1-12...

  • Page 23: Safety Signs And Labels

    Make sure that you can read all safety signs. Clean or replace these if you cannot read the words. View D View C View B Put into the pocket on the back of the seat. View A 9VXE ENG 1-13...
  • Page 24 4. Electric power lines (D405 Sign indicates electrocution hazard if machine is brought too near electric power lines. Keep a safe distance from electric power lines. 9VXE ENG 1-14...
  • Page 25 Sign indicates an electrical hazard from hot water or oil if radiator or hydraulic tank is handling cable. uncapped while hot. Read manual for safe and proper Allow radiator or hydraulic tank to cool before handling. removing cap. 9VXE ENG 1-15...
  • Page 26 Read manual before adjusting track for safe and proper handling. Operation prohibition during inspection servicing. Hang this sign on the control lever during inspection and servicing not to allow any other worker to start the engine or operate the machine. 9VXE ENG 1-16...

  • Page 27: Operation

    OPERATION This section describes the proper operation procedures of this machine. Always look to the safety and observe the given operation instructions and cautions to carry out works safely. 9VXE EN...
  • Page 28 9VXE EN...

  • Page 29: Names Of Components

    Slide pad Battery Boom Shoe adjusting device Hydraulic pump Arm cylinder Front idler Fuel tank Boom cylinder Blade cylinder Boom swing cylinder Control valve Blade Return filter Operator's seat Crawler shoe Hydraulic oil tank Swing unit Air cleaner 9VXE ENG...

  • Page 30: Controls And Instruments

    Throttle lever Engine oil pressure warning lamp Travel lever Hour meter Travel speed select pedal Light switch Blade/crawler operation lever Engine key switch Blade/crawler select lever Horn switch Boom swing pedal Operation lock lever Operator's seat Left operation lever 9VXE ENG...
  • Page 31 • It advances as long as the engine is running, even if the machine is not working. 5. Light switch The front light of the boom turns on when the mark is pressed. It turns off when the opposite side is pressed. WB-C210070 9VXE ENG...
  • Page 32 Set the switch to this position to start the engine. Release the fingers from the key immediately after the engine starts. The key returns to the ON position automatically. 7. Horn switch Horn switch Press this switch to turn on the horn. WB-C210090 9VXE ENG...
  • Page 33 Stop the engine and set the operation lock lever to the LOCK position before leaving the machine. • Note that boom swing operation is not locked even if the operation lock lever is set to the LOCK position. 9VXE ENG...
  • Page 34 Low speed 11. Throttle lever Use this lever to adjust the engine speed. • Low speed: Push the lever forward. High speed • High speed: Pull the lever backward. WB-C210130 9VXE ENG...
  • Page 35 The high speed changes into the low speed when you release your foot from the pedal. Speed changes into high speed by The travel speed may be changed during traveling or stepping on pedal. stopping. WB-C210150 9VXE ENG...
  • Page 36 Boom swing right: Step on the right side of the pedal. Boom swing right Lock Protect the pedal with the cover to disable pedal operation when boom swing operation is not Boom needed. Boom swing pedal swing left WB-C210170 9VXE ENG...

  • Page 37: Starting Engine

    • Push the light switch (5) and make sure that the front Unlock light is turned on. • Push the horn switch (6) and make sure that the horn sounds. WB-C210210 9VXE ENG...
  • Page 38 (preheat) position. However, this does not imply any abnormality. 3. Turn the key to the START position to start the engine. 4. Release your fingers from the key after the engine starts. The key returns to the ON (run) position automatically. 9VXE ENG 2-10...
  • Page 39 Then, disconnect the clip from the - terminal of the normal machine. 2. Disconnect the clip of the red cable from the + terminal of the normal machine first. Then, disconnect the clip from the + terminal of the machine in trouble. 9VXE ENG 2-11...
  • Page 40 (below 20ºC). The proper hydraulic oil temperature is 50ºC to 80ºC. Warm up hydraulic oil up to 20ºC or so and then carry out operation, if it is necessary to start operation at low temperature. 9VXE ENG 2-12...

  • Page 41: Stopping Engine

    Carry out repair work if leak or some abnormality is found. 2. Refill the fuel tank fully. 3. Remove soil and sand from around the crawlers and bucket. 4. Lock all the lockable parts such as the fuel port, engine cover, etc. WC-C200450 9VXE ENG 2-13...

  • Page 42: Running In New Machine

    4. Do not start, accelerate or stop the machine quickly or change the direction quickly. 5. Do not apply shocks such as quick stopping of the WC-C200470 boom when lowering it to the machine. 6. Grease the pins of the attachment everyday. 9VXE ENG 2-14...

  • Page 43: Lever Operations

    Swing right Arm in Swing right Check the action of each operation lever and movement of the machine before starting work in order to prevent accidents, which may result in injury or death, due to improper operations. 9VXE ENG 2-15...
  • Page 44 The operation mode plate shown below that indicates the operation system of the machine is stuck at the top of the lever stand on the operator's seat side. Operation mode Operation mode plate D40773300 STOP Pattern (AB select type) D40773300 D40773400 STOP Pattern A D40773400 D40773500 STOP Pattern F D40773500 9VXE ENG 2-16...
  • Page 45 3. Lower the attachment onto the ground and stop the engine before re-assembling the reach rods. Pattern A positions Pattern B positions Pattern A Pattern B Operation system changing plate Pattern A positions Pattern B positions D40538200 Operation system changing plate WB-C210280 9VXE ENG 2-17...

  • Page 46: Crawler Extension/Retraction Operation

    If the machine is traveled at the middle of the stroke, the travel linearity and operability are When retracted: 700 mm deteriorated and the machine body may 125 mm 125 mm become faulty. When extended: 950 mm Extended/retracted crawler dimension WB-C210310 9VXE ENG 2-18...

  • Page 47: Blade Operation

    Boom swing Boom swing left right Unlocked Pedal cover Boom swing right Locked Boom Boom swing pedal swing left WB-C210170 WB-C210340 Put the pedal cover on the pedal and lock it when boom swing is not carried out. 9VXE ENG 2-19...

  • Page 48: Swing Operation

    Turn the lever to the left. swing Return the lever to the neutral position to stop swinging. WB-C210350 Left swing Right swing WS-C200110 Do not let any persons enter the swinging range. Check the safety around the machine before swinging. 9VXE ENG 2-20...

  • Page 49: Traveling

    • • • • Stopping Set both travel levers to the neutral positions to stop the machine. When the machine stops, the parking brake is applied automatically. Forward Backward WB-C210390 9VXE ENG 2-21...
  • Page 50 1. Spin turning to the left. Push the right travel lever forward and pull back the left lever. 2. Spin turning to the right. Pull back the right travel lever and push the left lever forward. WB-C210430 Spin turning 9VXE ENG 2-22...
  • Page 51 When the machine moves across a slope, it may slide sideways. Move down the slope onto a flat ground, turn the machine, and travel safely. • WB-C210460 Do not travel on a 30º or more slope. WB-C210440 9VXE ENG 2-23...

  • Page 52: Work Instructions

    WC-C200720 Loading After digging, raise the boom, swing and load soil onto the dump truck. WC-C200730 Gutter Digging It is possible to dig gutters in narrow spaces by swinging the boom. WC-C200740 9VXE ENG 2-24...

  • Page 53: Precautions For Works

    WC-C200800 Do not overload to cylinder Do not forcefully conduct digging operation beyond the capacity, which may overload any cylinder and open its relief valves. This causes damage to the hydraulic system and machine. WC-C200810 9VXE ENG 2-25...
  • Page 54 Works in damp grounds Place mats or the like to protect the footing in advance when carrying out works in damp grounds or muddy places. Drive the machine with great care not to enter muddy places. WC-C200850 9VXE ENG 2-26...
  • Page 55 WC-C200890 abnormally. It is necessary to change grease in the turning structure or overhaul and repair the turning structure immediately. Stop operation and ask greasing, overhaul or repair works from the nearest service office. 9VXE ENG 2-27...

  • Page 56: Precaution On Use Of Rubber Shoe

    Do not travel or work on rocky site This causes damage of the lug and breakage of the steel cord. WC-C200910 Do not travel or work on riverbed This causes damage and slipping off of the shoe. WC-C200920 9VXE ENG 2-28...
  • Page 57 Do not travel over high heat locations Do not travel over place subjected to high heat such as bonfires or steel plate under scorching heat. This causes serious abrasion or damage and breakage of WC-C201020 the lug. 9VXE ENG 2-29...
  • Page 58 Always keep proper tension on the shoe If the rubber shoe is slack, it may damage the rubber shoe or cause them to come off the rollers. This causes damage and slipping off of the shoe. WC-C201060 9VXE ENG 2-30...

  • Page 59: Pto (Power Take-Off) For Special Attachment Use

    Adjust height of stop limit (2) in order that the Neutral position pedal (1) touches head of screw when is in neutral position avoiding eventual movement if we push on rear side. Contact with the pedal stopper at the pedal neutral position 9VXE ENG 2-31 WB-C210500...
  • Page 60 (1) touches head of screw when is in neutral position avoiding eventual movement if we push on rear side. Working position WB-C210520 Step on the pedal Contact with the pedal stopper when the pedali s stepped on WB-C210530 9VXE ENG 2-32...
  • Page 61 (actuator). Unlock The engine may fail to start if the lever (2) is set to Lock the ON position. Be sure to set the lever to the OFF WB-C210550 position when the power port is not used. 9VXE ENG 2-33...

  • Page 62: Towing

    Apply a wire rope to the pulling hook at the back of the lower frame using a shackle. • The maximum pulling load should be 500 kg or less. • Do not pull diagonally. Light-duty towing hook 9VXE ENG 2-34...

  • Page 63: Transport

    5. Adjust the machine to the ramp board direction, raise the blade and travel the machine slowly with care not to hit the attachment against the truck. 6. Load the machine properly in the designated position on the truck. 9VXE ENG 2-35...
  • Page 64 If wire ropes are applied to the rubber shoes directly when fixing the machine, the rubber shoes may be damaged. Put patches on the front and rear positions of the crawler frame and fix with the wire ropes. 9VXE ENG 2-36...

  • Page 65: Lifting The Machine

    7. Fasten the wire ropes to the lifting holes at both ends of the blade using shackles. 8. Lift the machine slowly until it is lifted slightly apart from the ground, stop lifting once, check the machine balance, and lift the machine to the intended height. WB-C210570 9VXE ENG 2-37...
  • Page 66 OPERATION 9VXE ENG 2-38...
  • Page 67 OPERATION This page is intentionally left blank 9VXE ENG 2-39...

  • Page 68: Maintenance

    Proper maintenance is needed to maintain the machine performances for long and prevent damages and troubles in advance. This section describes the proper maintenance procedures of this machine. Carry out maintenance safely and properly in accordance with the instructions described below. 9VXE EN...
  • Page 69 9VXE EN...

  • Page 70: Periodic Replacement Of The Important Parts

    Repair or replace these parts immediately if some abnormalities or defects are found in them even before the replacement interval. Also check the fuel hoses, cooling water hoses and hydraulic hoses in daily check, monthly check and yearly check. 9VXE EN...

  • Page 71: Maintenance Intervals

    Ring gear Bucket tooth Replace ∆ Bucket Replace ∆ Check wear & Rubber shoe ∆ deterioration Check and Shoe tension ∆ adjust Check oil leak ∆ Check oil qty & Travel reduction ∆ refill gear Change oil First time 9VXE EN...
  • Page 72 Check oil qty & ∆ refill Engine oil Change First time First Oil filter Replace time Check oil qty & ∆ refill Fuel tank Drain water ∆ Check ∆ Water separator Clean ∆ Replace element Fuel filter Replace Fuel hose Change 9VXE EN...
  • Page 73 Crank case Check breather Coolant path Clean Intake valve & exhaust valve seat Fuse Replace Fusible link Replace Check battery liquid qty & ∆ refill Battery Clean ∆ terminals Bolt tightening Retightening ∆ : Contact our dealer. 9VXE EN...

  • Page 74: Recommended Lubrication Table

    Total qty: 2.2 L Cooling system Coolant – Long-life coolant (LLC) added For engine only: 0.6 L Greasing Grease – Lithium grease EP2 Proper qty • The oil with the marks is used for the machine before shipment. 9VXE EN...

  • Page 75: Lubricate The Grease

    Boom foot pin Boom cylinder foot pin Boom cylinder rod pin Arm foot pin Arm cylinder foot pin Arm cylinder rod pin Bucket cylinder foot pin Bucket cylinder rod pin Arm link pin Bucket link pin Bucket pin 9VXE EN...
  • Page 76 Lubricate the machine everyday until its operation time reaches 100 hours, if it is a new machine. • Carry out greasing, regardless of the greasing interval, if abnormal noises are generated from a greasing point. • Be sure to grease the pins around the bucket before starting in-water digging. 9VXE EN...
  • Page 77 If greasing is carried out in the same position, grease is not spread all over the swing bearing. Be sure to swing the machine by approximately 90 degrees and grease the bearing at different points. 9VXE EN...

  • Page 78: Maintenance Of Bucket

    Link pin bucket link pin into the holes. Arm point pin Attach the ring pin to lock the bucket link pin. WB-C310070 Move the O-rings to the proper grooves. Grease the arm point pin and bucket link pin. 9VXE EN...

  • Page 79: Crawler Shoe

    Otherwise, water may come into a crack, which rusts steel cords and cuts off the rubber shoe. Dislocation of the iron core Exchange the rubber shoe with a new one if one or more iron cores are dislocated from it. 9VXE EN 3-10...
  • Page 80 10 to 20 mm (Rubber shoe) The machine needs to be raised to inspect the shoe tension. If the machine drops by mistake during inspection, a serious injury may result. Be very careful when the machine is raised. 9VXE EN 3-11...
  • Page 81 (It should be loosened by a maximum of one turn.) • Grease may spout out at high pressure. Never loosen the grease nipple. • Do not bring your face or hand close to the check valve during adjustment. 9VXE EN 3-12...

  • Page 82: Travel Reduction Gear

    6. Fill oil until it flows out from the filler/level port. 7. Clean both plugs and attach them. Specified oil Engine oil 0.33 L API CD, SAE30 The gear case and oil are hot immediately after stopping the engine. Wait until the temperature lowers. 9VXE EN 3-13...
  • Page 83 1. Loosen the drain plug (3) under the hydraulic oil tank to discharge water and sediment into the container. 2. Tighten the drain plug when clean hydraulic oil is only discharged. 3. Check the hydraulic oil level and refill oil if insufficient. 9VXE EN 3-14...
  • Page 84 7. Extend all cylinders fully, attach the oil filler plug, and pressurize the tank. When the breaker work is done, hydraulic oil is deteriorated more than normal digging works. Replace the filter cartridge every 100 hours. WB-C310160 Posture of pressurizing hydraulic oil tank WB-C310170 9VXE EN 3-15...
  • Page 85 Make sure that the oil level is between H and L of the level gauge (7). WB-C310200 10. Idle the engine for approximately two to three minutes at low speed. Bring the machine into the level checking posture and check the oil level. Refill hydraulic oil if insufficient. 9VXE EN 3-16...
  • Page 86 If the machine is used with deteriorated hydraulic oil, the hydraulic devices and the whole hydraulic circuit may become defective. Change hydraulic oil and clean the strainer every 500 hours. 9VXE EN 3-17...

  • Page 87: Hydraulic System Diagram

    Pump flow rate (Max.): Main relief valve P1 Pump 16.2 2347 11.1 L/min Main relief valve P2 Pump 16.2 2347 11.1 L/min Overload relief valve (Boom) 18.6 2702 Overload relief valve (Arm) 18.6 2702 Swing relief valve 9VXE EN 3-18...

  • Page 88: Engine Oil

    Check the oil level 10 minutes or more after Lower limit stopping the engine, if the engine has started. WC-C300320 • Do not start the engine if the oil level exceeds the upper limit or below the lower limit. 9VXE EN 3-19...
  • Page 89 12. Idle the engine for several minutes, stop the engine, and check the level of engine oil 10 to 20 minutes later. Refill the engine with engine oil up to the specified level if the oil level is low. 9VXE EN 3-20...

  • Page 90: Fuel System

    Discharging Water from Fuel Tank 1. Open the drain plug at the bottom of the fuel tank to discharge water and sediment before starting work. 2. Close the drain plug when clean fuel comes out. Drain plug WB-C310280 9VXE EN 3-21...
  • Page 91 Fuel is hot immediately after stopping the engine. Carry out the work after the fuel temperature has become lower. • Do not bring fire close to the engine. • Wipe off spilt fuel completely. If it is left as is, it may cause a fire. 9VXE EN 3-22...
  • Page 92 Carry out the work after the fuel temperature has become lower. • Do not bring fire close to the engine. • Wipe off spilt fuel completely. If it is left as is, it may cause a fire. 9VXE EN 3-23...

  • Page 93: Cooling System

    Wash your eyes completely with water immediately and consult a doctor, if it is put into the eyes. • Use a container with an antifreeze mark to store long life coolant. Cap the container and store it in a place not accessible by children. 9VXE EN 3-24...
  • Page 94 Internal air is discharged and the water level lowers. Refill coolant close to the water filler port and tighten the cap. 10) Discharge coolant from the subtank (4), clean the inside of the tank, fill the tank with coolant up to the FULL mark. 9VXE EN 3-25...
  • Page 95 2) Turn the adjust bolt (3) to move the generator (3) so that the belt slackens by approximately 10 mm. WB-C310350 3) Tighten the bolt and nut. 4) Replace the bolt if it has elongated and the adjustment margin is lost. 9VXE EN 3-26...
  • Page 96 Use high-pressure water and compressed air at as WB-C310370 low pressure (0.2 MPa) as possible. Do not use a wire brush to clean the fins. A wire brush may damage the fins. 9VXE EN 3-27...

  • Page 97: Intake Air System

    If it is carried out while the engine is running, dust is sucked and the engine may be damaged. • Put on protective goggles when cleaning the element using compressed air. Otherwise, dust may be put in your eyes, which is dangerous. 9VXE EN 3-28...

  • Page 98: Engine

    As a result, the cooling efficiency is reduced, the engine oil is not cooled sufficiently and oil is deteriorated earlier. Lap Intake and Exhaust Valves Adjustment is necessary to maintain proper contact of the valves and seats. 9VXE EN 3-29...

  • Page 99: Electric System

    ON position, the fusible link between the battery and the engine key switch circuit may have blown out. Remove and check the fusible link. Replace it with a new fusible link, if it has blown out. WB-C310480 9VXE EN 3-30...
  • Page 100 2. Detach the terminals and polish them with a wire brush or sandpaper if they are corroded remarkably. 3. Apply grease, etc. thinly to the terminals after cleaning and tightening. 9VXE EN 3-31...

  • Page 101: Electric System Diagram

    MAINTENANCE ELECTRIC SYSTEM DIAGRAM 9VXE EN 3-32...
  • Page 102 MAINTENANCE 9VXE EN 3-33...
  • Page 103 Water temperature sensor Battery charge warning lamp Charge lamp / Hour meter relay Hour meter Safety relay Diode Engine key switch Timer (1sec) Current limiter Engine stop relay Light switch Engine stop solenoid Boom light Glow plug Fuse box 9VXE EN 3-34...

  • Page 104: Tighten Bolts

    Travel reduction gear Bar 8 Drive sprocket Bar 8 Lower roller 2. Swing unit WB-C310420 Tightening torque Wrench size Tightening position Bolt size (mm) (N·m) (kgf·m) Swing motor Bar 10 Swing gear case M10 P1.25 Swing bearing 9VXE EN 3-35...
  • Page 105 High-pressure hose union nut Coarse thread Fine thread Bolt Wrench size Hose size (N·m) (kgf·m) size (mm) (inch) (N·m) (kgf·m) (N·m) (kgf·m) 1/4" 3/8" 1/2" 13.7 13.8 3/4" 12.0 21.2 22.5 1" 14.0 41.9 46.1 1-1/4" 17.0 72.9 82.7 9VXE EN 3-36...

  • Page 106: Handling In Cold Weather

    • Put plates on dry and firm ground and park the machine on them in order to prevent the crawlers from freezing. • Discharge water from the fuel tank to prevent fuel from freezing. 9VXE EN 3-37...

  • Page 107: Long Term Storage

    • Check the lubrication and greasing conditions of each part and the coolant level. • Wipe off grease from the hydraulic cylinder. • Start the engine, warm it up, and carry out traveling, swinging and attachment operations several times repeatedly to run in each part. 9VXE EN 3-38...

  • Page 108: Specifications

    SPECIFICATIONS 9VXE EN...
  • Page 109 9VXE EN...

  • Page 110: Speed And Gradeability

    890 kg Average ground 26 kPa bearing pressure CAPACITY Fuel 8.5 L Tank level 8.2 L Hydraulic oil Total quantity 14.0 L Maximum 1.8 L Engine oil Minimum 1.2 L Engine only 0.6 L Coolant Total quantity 2.2 L 9VXE EN...

  • Page 111: Bucket

    General digging ⊕ ⊕ ⊕ ⊕ 0,021 General digging Ditch digging 0,016 General digging General digging Using buckets larger than the standard, where permitted, must be done with great caution to avoid tipping the machine over and damaging structures. 9VXE EN...

  • Page 112: Dimensions

    Blade width Blade forward 2700 Overall length Blade backward 2980 Minimum radius of equipment and attachment 1220 Overall height at minimum radius of equipment 2180 and attachment Attachment height in transport posture Blade maximum lifting Blade maximum lowering 9VXE EN...

  • Page 113: Working Range

    Reach at maximum dumping height 1590 1700 Minimum dumping height Reach at minimum dumping height 1120 1220 Maximum vertical digging depth 1175 1400 Reach at maximum vertical digging depth 2160 2140 Minimum level floor radius 1040 Maximum level floor radius 2290 2500 9VXE EN...

  • Page 114: Working Range For Offset Digging

    SPECIFICATIONS WORKING RANGE FOR OFFSET DIGGING WB-C410030 Unit: mm Left boom swing 1105 Minimum radius of equipment at maximum front offset Right boom swing 9VXE EN...
  • Page 115 SPECIFICATIONS This page is intentionally left blank 9VXE EN...
  • Page 116 MINI EXCAVATOR 9VXE PUBLISHED: JUNE 2012 IHIMER S.p.A. ITALY...
  • Page 118 IHIMER Spa 53037 San Gimignano - Loc. Cusona (SI) - Italy info@ihimer.com | www.ihimer.com...

Table of Contents