Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Excel 11051
- Page 1 MODEL:11051...
-
Page 2: Scope Of Delivery
carefully follow its information. The machine can only 1. Introduction operated persons were instructed concerning Dear Customer, the operation of the machine and who are informed We hope your new tool brings you much enjoyment and about the associated dangers. The minimum age success. -
Page 3: Safety Instructions
•The machine is intended for use only with original 4. Safety instructions spare parts and original tools from the producer. •The equipment is allowed to be used only for its Caution! In order to protect yourself from the danger of prescribed purpose. - Page 4 8. Wear suitable clothing. 16. Make sure that no spanners, keys etc. are left •Do not wear loose-fitting clothing or jewellery. They attached. could become caught on moving parts. •Check before switching on that all spanners, keys and •We recommend that you wear anti-slip footwear when setting tools have been removed.
- Page 5 i)Guide work piece by the fence to maintain control of Safety advice relating specifically to router tables work piece. Do not place material between router bit a)Read and understand table and router manual and and fence while routing the edge. This placement will accessory warnings.
-
Page 6: Technical Data
q) Use push sticks, vertical and horizontally mounted 6.Product Features feather-boards (spring sticks), and other jigs to hold down the work piece. Push sticks, feather-boards, and 1.Extractor Hood jigs eliminate the need to hold the work piece near the 2.Back Guide Fence spinning bit. - Page 7 – Secure the hood to the Fence base using 2 x hood 7. Assembly screws(10), 2 x small washers(17) and 2 x hood Avoid unintentional starting of the machine. During nuts(11). assembly and for all work on the machine, the power plug must not be connected to the mains supply.
- Page 8 – Attach the feather-boards to each side using 2 x Be aware that the screws must be inserted through the feather-board screws (15), 2 x knob nuts (14) and 2 x slotted hole on the table from underneath so that the large washers (16).
- Page 9 Stationary or Flexible Mounting To ensure safe handling, the machine must be mounted on a level and stable surface (e. g., workbench) prior to using. Mounting to a Working Surface – Fasten the power tool with suitable screw fasteners to the working surface.
-
Page 10: Operation
Adjusting the Router Speed 8.Operation Be aware you should always make sure that on/off switch (5) is set to the off position and that the tool is not plugged in to any outlet before making any adjustments to the router table. Installing and Removing Collet(7). -
Page 11: Maintenance And Service
– When you have finished, push the off switch, allow the 10. Electrical connection machine to come to a full stop, and then unplug the machine form the outlet. The installed electric motor is factory connected ready for operation. The connection meets the applicable 9.Maintenance and Service VDE and DlN regulations. -
Page 12: Parts Diagram And Parts List
Parts Diagram and Parts List... - Page 13 Parts Diagram and Parts List...
- Page 14 Parts Diagram and Parts List...
- Page 15 Parts Diagram and Parts List TABLE PARTS Art. number Description 10250027 TABLE COMPONENTS 20250002 SLIDING GUIDE 50010030 COLUMNED PIN 50020019 M6X30 SCREWS 10060021 POINTER 50040070 M5X6 SCREWS 50060015 M6 NUTS 30080037 COVER OF SMALL KNOB 30080035 BODY OF SMALL KNOB 50010084 BIG WASHERS 30200016...
- Page 16 Parts Diagram and Parts List SWITCH BOX PARTS Art. number Description 30130009 EMREGENCY STOP 50040067 M6X16 SCREWS 30130006 PLASTIC NAIL 30130013 SWITCH BASER 50060033 M6 NUTS 50230016 ENDDING 70120007 WIRE (WITH) 50230008 PLUG&CONNECTING 50230018 BLUE SETS 70120009 WIRE (BLUE) 70120008 WIRE (BLACK) 10380069 INDUCTANCE...
- Page 17 Parts Diagram and Parts List MOTOR PARTS Art. number Description 50010100 M16 RING 10130044 WRECH 10130033 FIXING CAP 10130032 COLLECTOR 1/2 & 1/4 10250004 PRESS SPRING 10250005 LOCKING PIECES 10250006 DUST BLOCKER 50070010 M5X12 SCREWS 50010022 SPRING WASHER 50010034 M5 WASHERS 20250001 FORNT COVER 10250007...
- Page 18 Parts Diagram and Parts List MOTOR PARTS Art. number Description 30060019 HANDLES 50060033 M6 NUTS 30070015 HAND WHEELS 50050019 M6X12 SCREW 10250024 ADJUSTING PARTS 50010035 WASHER M6 50060023 M6 NYLON NUTS 50010023 M6 SPRING WASHERS 50030019 M6X12 SCREWS 10250031 SHAFT 30250001 LOCKING HANDLE 50040020...
Need help?
Do you have a question about the 11051 and is the answer not in the manual?
Questions and answers
what is the in or out knob under the table below the four screws on top of table