Advertisement
Quick Links
Advertisement
Summary of Contents for INLAYLINK E710B
- Page 1 E710B RFID Module User Guides www.inlaylink.com...
- Page 2 Catalogue Product introduction ・・・・・・・・・・・・・・・・・・・・・・・・01 Main features ・・・・・・・・・・・・・・・・・・・・・・・01 Applications ・・・・・・・・・・・・・・・・・・・・・・・・01 Warning ・・・・・・・・・・・・・・・・・・・・・・・・・・01 FCC regulatory compliance statement ・・・・・・・・・・・・02 Main technical specifications ・・・・・・・・・・・・・・・・・・・・06 Interface specification ・・・・・・・・・・・・・・・・・・・・・・・03 Software ・・・・・・・・・・・・・・・・・・・・・・・・・・・・08 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・04 Basic settings ・・・・・・・・・・・・・・・・・・・・・・・05 RF Configs ・・・・・・・・・・・・・・・・・・・・・・・・10 Real-time tag inventory ・・・・・・・・・・・・・・・・・・・12 Access tag ・・・・・・・・・・・・・・・・・・・・・・・・14...
- Page 3 Product introduction Main features ·Small size， big energy ·Outstanding board level cooling design ·Extreme appearance design ·Low power consumption, sleep power down to uA level ·8 Antenna ports 、 USB Type-C communication power supply ·Twice the reading range and sensitivity compared to the R2000 Industry application Logistics, warehousing, express delivery, stores, financial management, etc.
- Page 4 Antenna Type Brand/ manufacture Model No. Max. Antenna Gain PCB antenna INLAYLINK iA90N10S -15dbi Instruction to Host product manufacturer when choosing external connector: Unique antenna connector must be used on our Part 15 authorized transmitters used in the host product. Here is a list of acceptable unique connectors: Brand/ manufacture Model No.
- Page 5 For FCC, this exterior label should follow “Contains FCC ID: 2A92M-E710B” . In accordance with FCC KDB guidance 784748 Labeling Guidelines. ” § 15.19 Labelling requirements shall be complied on end user device.
- Page 6 Product introduction FCC regulatory compliance statement FCC other Parts, Part 15B Compliance Requirements for Host product manufacturer This modular transmitter is only FCC authorized for the specific rule parts listed on our grant, host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.
- Page 7 Product introduction FCC regulatory compliance statement For Class A Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 8 Main technical parameters Performance specifications Physical specifications Communication interface Dual-core Cortex-M33 Transmission rate USB： 3Mbps Internal storage 512KB Antenna interface 8Port (I-PEX) Memory 1MB+8MB Power supply mode USB Type-C Rated power Materials Working environment Size 70mm x 35mm x 5 mm Weight Working temperature -20 ℃~+65℃...
- Page 9 Interface specification USB Type—C Indicating Lamp...
- Page 10 Software The application software interface consists of the function menu bar on the left, the software operation panel on the right, and the information bar at the bottom, as shown in Figure 5-1. Figure 5-1...
- Page 11 On the basic parameter setting page, select the corresponding serial port number, serial port baud rate, and reader model to 115200 and E710B, and click Connect Reader. After the connec- tion is successful, click "Firmware Version" to display the publication number, which can prove...
- Page 12 Software Figure 5-3 RF Configs Click "RF Configs" to set the RF mode of the reader, as shown in Figure 5-4. Figure 5-4...
- Page 13 Software RF Configs In the antenna parameter column, you can view the power, working time and counting times of each antenna. Click the antenna name to select the enabled antenna (after successful selection, the antenna name will be displayed in blue), enter the value, and click "set". The maximum power is 27dBm.
- Page 14 Software Select the RF spectrum (FCC, ETSI, CHN). The default value is CHN(China). Select the antenna and set the power and inventory time. Adjust the Q value based on the actual situation (the more tags, the larger the Q value). Set the idle time of the antenna to reduce power consumption (0 by default).
- Page 15 Software There are two types of inventory mode, Target and Session. The parameters are as follows: 1) Taget, Tag interface A: Select the status of Tag side A B: Select the status of Tag side B AB: Select the round-cut status of both Tag side A and B 2) Session, Tag Session value: S0: Tags change status immediately after being counted S1: The tag will stay 0.5-5 seconds to change its status after being counted...
- Page 16 Software Access tag Click "Access Tag" to read, write, set, and destroy tags. As shown in Figure 5-7. Figure 5-7 1) Select Tag After checking the tags in the real-time inventory TAB page, select the tag EPC to be operated in the "tag List"...
- Page 17 5) Tag extension function When the Fast Id function is enabled, TID data can be displayed on the tag inventory interface. Note: The above is the basic operation steps, detailed operation see the Inlaylink reader Demo program instruction.
- Page 18 Name Shanghai Inlay link Inc. Address No.164 Xuanchun Road, Pudong District, Shanghai, China Phone （86） -021-58039288...
Need help?
Do you have a question about the E710B and is the answer not in the manual?
Questions and answers