Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Ashbys SENSEI
- Page 1 Instruction Manual Operators and maintenance personnel must read and understand this manual before attempting to operate the unit. This manual has important information for use and safe operation. Keep this manual on file and readily available. Ashbys Cleaning Equipment info@ashbys-uk.com...
-
Page 2: Table Of Contents
Emptying Sensei after Water Extraction Cleaning ..................5 Hot Solvent Cleaning ............................6 Emptying Sensei after Solvent Extraction Cleaning ..................7 Water Cleaning with a Hot Solvent Sensei ....................7 Maintenance ..............................7 Exploded Diagram ............................9 Parts List ................................10 Wiring Diagram for MK1 Sensei without Heater ..................12... -
Page 3: Important Safety Instructions
Important Safety Instructions When using an electrical appliance to reduce the risk of fire, electric shock or injury, basic precautions should always be followed including but not limited to the following – 1. Do not leave a machine plugged in. Unplug from outlet when not in use and before servicing. Servicing should only be carried out by qualified personnel. -
Page 4: Before Operating The Machine
1. Connect Sensei mains lead to 13 amp socket. Only use electrical supply with earth leakage trip. If your Sensei is fitted with an internal heater, water in the solution tank can be heated to a pre- set temperature of approx. 75˚C. -
Page 5: Emptying Sensei After Water Extraction Cleaning
– commence cleaning in the normal way, fill solution tank with water & chemical mix as and when needed. Warning : Use only Ashbys approved water extraction detergent mix. Do not use chemicals intended for pre-spray or rotary use. These will invalidate machine warranty. -
Page 6: Hot Solvent Cleaning
When the neon light above the heater switch is off, the water is up to temperature and the machine is ready to use. Ensure Flow Control Valve on Sensei is closed and switch on pump. Solvent will be drawn from the 5 Ltr container, through a heating coil and be vented into the bucket. -
Page 7: Emptying Sensei After Solvent Extraction Cleaning
Once this is done, remove the Solvent Intake Hose from the 5 Ltr container of Ashbys Dry Clean Extra PC4502. Put the open end of the Solvent Bleed Hose into the 5 Ltr container of Ashbys Dry Clean Extra PC4502 and switch on the pump to drain the system of solvent. Run the pump until dry. - Page 8 Spits of water coming from the exhaust vent located at the rear of the SENSEI is a tell-tale sign of this problem. Should this happen, stop the machine, run the vacuum motor with recovery tank lid off and replace the float cage if necessary.
-
Page 9: Exploded Diagram
Exploded Diagram Page 9 of 13... -
Page 10: Parts List
1” ABS Pipe 1-1/2 260-01 ABS NID Adaptor 1-1/2” 270-05 Quick Connect Female 1/4” Brass 300-07A PHSM Screw #6 X 1/2 Black 065-03F Solution Cover Sensei 170-22A Switch Plate Label See 6 050-30 Panel Lamp 335-08 Switch Plate Sensei 390-09 Washer 9/16”... - Page 11 020-29 Hex Bolt ¼ X 20 X 1/2 S/S 300-21 Shoulder Bolt 065-39 Access Plate W / Hinge Sensei 065-41 Bracket Wheel Sensei 040-08 Wheel 8” Grey Centred 390-03 Washer 1/4” S/S 020-05 Hex Bolt 1/4 X 20 X 1” Zinc...
-
Page 12: Wiring Diagram For Mk1 Sensei Without Heater
Wiring Diagram for MK1 Sensei without Heater Wiring Diagram for MK1 Sensei with 1500W Heater Page 12 of 13... -
Page 13: Warranty
We, Ashbys Specialist Cleaning Equipment, (hereinafter referred to as Ashbys), hereby warranty the Sensei machine for one year from date of purchase if purchased new or three months from date of purchase if purchased from Ashbys as reconditioned / second-hand. If purchased new, this is subject to a Full Service (which is chargeable –...
Need help?
Do you have a question about the SENSEI and is the answer not in the manual?
Questions and answers