Related Manuals for Hisense Laser TV 100L9G-B12
Summary of Contents for Hisense Laser TV 100L9G-B12
- Page 1 USER MANUAL Read the manual carefully and ensure you have fully understood its contents before operating this device for the first time. English...
- Page 2 ▌Important Notice Paragraphs beginning with the symbol indicate important instructions, tips or conditions for the following settings. For your own safety and the optimal performance of your device, ensure to read the safety instructions before performing any installation. Compatibility with 3rd party products, software and services are not guaranteed. We cannot be held liable for any damage or loss suffered whilst operating, using or connecting to incompatible devices or apps.
- Page 3 The intended use and ambient conditions for this device This device is intended for the rendering of video and audio signals, on a table-top, in a home or office environment. It must not be used in rooms with a high level of humidity or dust concentration. The warranty is only valid if used as intended by the manufacturer. WARNING High humidity and dust concentration may lead to current leaks in the device.
- Page 4 „ Power Supply „ Power plug and power cable Incorrect voltages can damage the device. Only connect this unit - Do not touch the power plug with wet hands. to a power supply with the correct voltage and frequency noted - Do not place heavy objects on the power cable.
- Page 5 „ Thunder Storms become hot. - Do not insert foreign objects into the device through the vents. Pull out the power plug and all connected antenna cables from the device during a thunderstorm. Overvoltage caused by „ Warning about off-gassing lightning strikes can damage the device via the antenna system, as well as the wall socket.
- Page 6 - Also wipe the power plug with a dry cloth at regular intervals. - Do no use rechargeable batteries. - Do not burn or break up batteries. „ Service/Repair - Be sure to dispose of batteries correctly. - Do not expose batteries to excessive heat such as sunshine, Never remove the cover/back of the device;...
- Page 7 - If any object or water enters this device, please unplug this device and contact the service staff of Hisense. - Clean the lens periodically with a clean cloth and make sure the TV is turned off before you start.
-
Page 8: Table Of Contents
Congratulations on the purchase of your new TV! This Manual will walk you through a few easy steps to set up your TV. Please visit Hisense official website for more details. Product image is only for reference, actual product may vary in appearance. -
Page 9: Accessories List
• Do not allow a child to stand on or climb up this device. • Do not place any object above or in front of the lens because the laser light could cause the object to become flammable. • Clean the lens periodically with a clean cloth and make sure the TV is turned off before you start. Accessories List •... -
Page 10: Laser Tv Diagram
Laser TV Diagram Air vents Power Indicator Remote control receiver Eye protection sensor Power button Lens with laser Foreign Object Detect We strongly recommend that two people handle this device when moving it from one place to another. Be sure to protect the lens when you handle this device. -
Page 11: Step 1 Mount The Screen
STEP 1 Mount the Screen Screen installation please refer to the specific screen installation guide! STEP 2 Install the Laser TV We strongly recommend that two people handle this device when moving it from one place to another. Be sure to protect the lens when you handle this device. - Page 12 Ethernet (you will need a router for Internet connectivity) (not included) Satellite antenna NOTE: ANT2 Jack supports power supply for satellite antenna (13/18V, 0.5A max.) Outdoor Antenna Cable ANT OUT Antenna Cable (75Ω) VHF/UHF Antenna CAM CARD SMART CARD NOTE: Before you insert/remove the CI+ module, ensure that the TV is switched off.
- Page 13 NOTE: When connecting a hard disk or a USB hub, always connect the mains adapter of the connected device to the power supply. Exceeding a total current consumption may result in damage. The USB1.1 and USB2.0 devices maximum current consumption are 500mA. For individual non-standard high-capacity mobile hard disk, if its impulse current is greater than or equal 1A, it may cause TV-rebooting or self-locking.
- Page 14 Wired setup LAN ( Connect your TV to your network by connecting the LAN port on the back of your TV to an external modem or router using a LAN (Ethernet/Cat 5) cable. See the illustration below. TV PORT IP Sharer (Router) External Modem (with DHCP server) (ADSL / VDSL / Cable TV)
- Page 15 WARNING: Insufficient ventilation space will cause Plug the power cord into a wall outlet. this device to overheat or become damaged. Press the POWER button to turn on the Laser TV. • Do not block the air vents or place any object on this device. •...
-
Page 16: Step 3 Adjust The Display Image And The Screen
STEP 3 Adjust the Display Image and the Screen Follow the steps in the order shown below, only if they apply to your situation. NOTE: Before adjusting, fold the wall-mount bracket wands so that screen is vertically level. Rotate feet from an overlooking view, but do not look directely at the lens when the Laser TV is on because the laser light may damage your eyes. - Page 17 • If the bottom of the image is wider than the screen, then ADJUST THE UPPER-RIGHT CORNER OF THE IMAGE move the Laser TV closer to the screen. 1. If the top of the image is lower on the left and higher on the right, then use the wrench to rotate the front-right foot and the back-right foot clockwise to the same height.
- Page 18 4. If the upper-right corner is inside the screen after adjusting, 2. Now, rotate the TV clockwise so that the bottom of the image use the wrench to rotate the front-right foot and the back- is parallel with the screen. right foot counterclockwise to the same height, and rotate the TV clockwise, to make the image parallel with the screen.
- Page 19 FILL THE TOP OF THE IMAGE TO THE SCREEN If the top of the image is wider than the screen, then use the wrench to rotate the left- and right-front feet of the Laser TV clockwise. If the top of the image is narrower than the screen, then use the wrench to rotate the left- and right-back feet of the Laser TV clockwise, until the left and right borders of the image are parallel with the screen borders.
-
Page 20: Step 4 Use Your Remote
STEP 4 Use Your Remote BUTTONS ON YOUR TV REMOTE NOTE: The button labels are provided as a reference. The actual appearance of the remote that is included with the TV, may differ from this diagram. Power Standby button: Power on / Standby Display the Home screen Turn on/off the teletext function Change volume... - Page 21 BUTTONS ON YOUR TV REMOTE NOTE: The button labels are provided as a reference. The actual appearance of the remote that is included with the TV, may differ from this diagram. Power button Exit the menu Turn on/off the teletext function Change volume Select input sources Display the Home screen...
- Page 22 1. Press the switch and the battery case REMOTE CONTROL RANGE INFORMATION will pop up automatically. • The remote control can work at a distance of up to 8 metres 2. Insert two AAA size batteries. Make in front of the TV set. (This distance is used by infrared sure to match the (+) and ( - ) ends of means in an unpaired state.) the batteries with the (+) and ( - ) ends...
-
Page 23: Step 5 Proceed Through The Screen Setup Menu
STEP 5 Proceed through the Screen Setup Menu PROJECTION MODE If you need to flip the image over top-to-bottom and/or left-to- right, select the Projection Mode. Alignment grid AUTO GEOMETRIC CORRECTION Before you use Auto Geometric Correction function, ensure 4. Click "+" on your mobile device to take a photo of the entire that the Laser TV and your mobile device are connected to the screen and image. -
Page 24: Step 6.Tv Setup
Select the Country where you will operate 3. Press button to save your adjustment, and you can select Country the TV. other points to adjust the image. Select the local time zone according to If you want to return the image position to the factory default, Time Zone your region. -
Page 25: Maintenance & Quick Problem-Solving Tips
Maintenance • Do not touch this device when it is running or just turned off because it may be hot. • Do not wipe this device with oil because it may deteriorate the exterior or damage the paint. Contact with rubber or ethylene products for a long time may cause stains on this device. - Page 26 I have connected an external source to my TV and I get no picture and/or sound. 1. Check for the correct output connection on the external source and for the correct input connection on the TV. 2. Make sure you have made the correct selection for the input mode for the incoming signal. The picture is normal but there is no sound 1.
-
Page 27: Product Specifications
Product Specifications Model Name 100" Laser TV 24.0 × 6.1 × 13.6 inches Dimension (W × H × D) (610 × 155 × 346 mm) Weight 24.7 lbs (11.2 kg) Active Screen Size (Diagonal) 100 inches Screen resolution 3840 × 2160 Audio power 2 ×... - Page 28 Model WF-M668-UWP1 Bluetooth Module Frequency Range 2.4~2.4835GHz specifications Output Power (Max.) 2.4~2.4835GHz,Class1,6dBm Model ERF6A64 / ERF6B64H Remote Control Frequency Range 2.4~2.4835GHz specifications Output Power (Max.) 2.4~2.4835GHz 5dBm Temperature: 41°F - 104°F (5°C - 40°C) Environmental conditions Humidity: 20% - 80% RH Atmospheric pressure: 86 kPa - 106 kPa RGB / 60 Hz (640×480, 800×600, 1024×768) YUV / 60 Hz (480i, 480p, 720p, 1080i, 1080p)
-
Page 29: Recycling / Licenses
Recycling / Licenses The terms HDMI and HDMI High- WEEE (Waste Electronic Electric Equipment) Definition Multimedia Interface, and European Directive 2012/19/EU the HDMI Logo are trademarks or registered trademarks of HDMI Licensing This symbol on the product or on its packaging indicates that Administrator, Inc. - Page 30 SIMPLIFIED EU DECLARATION OF CONFORMITY Hereby, Hisense Visual Technology Co., Ltd. declares that the radio equipment type [100L9GE / 100L9 / 100L9G / 100L9GA / 100L9GB / 100L9GC / 100L9GCH / 100L9GTUK / 100L9GTUKA / 100L9GTUKB / 100L9GTUKC / 100L9G-A12 / 100L9G-B12 / 100L9G-C12 / 100L9G-D12 / 100L9GCH-A12 / 100L9GCH-B12 / 100L9GTUK-A12 / 100L9GTUK-B12 / 100L9GTUK-C12 / 100L9GTUK-D12 / ERF6A64 / ERF6B64H] is in compliance with Directive 2014/53/EU.
- Page 31 ES-A2132Z2-1...