Do you have a question about the 3US-AS01 and is the answer not in the manual?
Questions and answers
Summary of Contents for Filtrete 3US-AS01
Page 1
User Manual of Product 1: Pyle Indoor Outdoor PA Horn Speaker - 19.5" 100W Power Compact Loud Sound Megaphone w/ 400Hz-5KHz Frequency, 16 Ohm, 100V/70V Transformer, Mounting Bracket - 100V/70V Audio System - PyleHome PHSP20 User Manual of Product 2: Pyle PCM20A - Compact Mini Home Power Amplifier - 40W Smart Small Audio Stereo Receiver w/ AUX 2 Microphone IN COM/8-Ohm/25V/70V Speakers LED Input Selector For PA...
Page 2
Homeowner: Please retain for operational and future maintenance instructions. 3US-AS01 3US-AS01 3US-AS01 System tested and Certified by NSF International against NSF/ANSI Standard 42 for the reduction of claims specified on the Performance Data Sheet. 3US-PS01 This is a chemical and mechanical reduction filter.
Water Filtration Systems. Retain these instructions for future reference. Intended use: The Filtrete Standard, Advanced and Maximum Under Sink Water Filtration Systems (3US-AS01, 3US-PS01, ™ and 3US-MAX-S01) are intended for use in filtering potable water and have not been evaluated for other uses.
• Where a booster pump is installed on a water • DO NOT install unit if collet is missing. Contact 3M system, you MUST maintain and inspect the if collets are missing from any fittings. attached pressure switch regularly in accordance •...
BEFORE YOU BEGIN: You will need an adjustable wrench for this installation. Remove items stored under the sink. Have a towel and bowl available in case dripping occurs. This system uses push-in fittings: This easy-to-install system uses watertight, push-in fittings. To Attach Tubing: To Release Tubing: (Fig.
Page 6
(Fig. 9.1) ATTACH WATER SUPPLY HOSE: You will need: 1 length of 3/8" blue tubing (C). 1. Insert one end of one of the lengths of 3/8" blue tubing (C) into the push-in fitting side of the male water supply line adapter (D) you just installed.
Page 7
ATTACH THE FILTER: You will need: filter (A) (Fig. 13) 1. Insert the filter (A) into the filter head assembly (B). 2. Push filter up, then turn one quarter of a turn to the right until it stops. The filter will rotate very easily during the first portion of the rotation.
TURN WATER ON: 1. Turn the water back on at the cold water shutoff valve. (Fig. 14) 2. Run water to flush 10 gallons (37.85 liters) (Fig. 14) through the system before use. (Approximately 5-7 minutes.) 3. Check for leaks. If any dripping or leaking occurs, turn cold water supply off, tighten fittings and assure that tubing is pushed completely into fittings.
Propietario: Por favor consérvelo para leer las instrucciones de funcionamiento y el futuro mantenimiento. 3US-AS01 Sistema 3US-AS01 probado y certificado por NSF International contra la norma 42 de NSF/ANSI para la reducción de 3US-AS01 reclamos especificados en la Hoja de datos de rendimiento.
Los sistemas de filtrado de agua Filtrete™ estándar y avanzados para bajo fregaderos (3US-AS01, 3US-PS01 y 3US-MAX-S01) están diseñados para usar en el filtrado de agua potable y no han sido evaluados para otros usos. El producto se deberá instalar en el lugar de uso y como lo indican las instrucciones de instalación.
• Si hay un dispositivo de prevención de retorno • Cuando haya una bomba elevadora de presión instalada en un sistema de agua, DEBE instalar una instalado en un sistema de agua, se DEBE instalar válvula reguladora de presión adecuada y regular un dispositivo controlador de presión debida a la la presión de agua a <80 psi.
ANTES DE COMENZAR: Necesitará una llave ajustable para esta instalación. Retire los elementos que guarda debajo del fregadero. Tenga a mano una toalla y un bol en caso de goteo. Este sistema utiliza conexiones a presión: Este sistema de fácil instalación utiliza conexiones a presión, herméticas.
Page 14
CONECTE LA MANGUERA DE SUMINISTRO DE AGUA: (Fig. 9.1) Necesitará: 1 segmento de tubería azul de 3/8" (C). 1. Inserte un extremo de uno de los segmentos de la tubería azul de 3/8" (C) al lateral de la conexión a presión del adaptador macho de la línea de suministro de agua (D) que recién instaló.
Page 15
(Fig. 13) CONECTE EL FILTRO: Necesitará: filtro (A) 1. Inserte el filtro (A) en la unidad de la cabeza del filtro (B). 2. Empuje el filtro hacia arriba, luego gírelo un cuarto de vuelta hacia la derecha, hasta que se detenga. El filtro girará muy fácilmente durante la primera parte de la vuelta.
ABRA EL AGUA: (Fig. 14) 1. Vuelva a abrir el agua en la válvula de cierre del agua fría. (Fig. 14) 2. Deje correr el agua hasta que purgue 37,85 litros (10 galones) a través del sistema antes de utilizar. (Aproximadamente de 5 a 7 minutos.) 3.
Need help?
Do you have a question about the 3US-AS01 and is the answer not in the manual?
Questions and answers