Thiel SI 1 User Manual
Subwoofer integrator
Hide thumbs
Also See for SI 1:
- Brochure (4 pages) ,
- Specifications (12 pages) ,
- Product support bulletin (6 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Thiel SI 1
Summary of Contents for Thiel SI 1
-
Page 1: Owner Information
THIEL SmartSub ™ SI 1 Integrator Owner Information... -
Page 3: Table Of Contents
Remote Control Command Codes ... 13 Introduction The SI 1 SmartSub Integrator provides unprecedented ability to perfectly match any SmartSub with any main speakers, and provide total system performance that is as well integrated and balanced as a full range speaker. This superior performance is achieved by innovative circuitry (patent 6,687,379, other patents pending) that automatically calculates the ideal subwoofer response to perfectly match the characteristics of the main speakers. -
Page 4: Connecting The Integrator
LFE or subwoofer output to the Integrator’s LFE input. 3 3 3 3 3 If you are using a second Integrator or a THIEL passive crossover to derive a subwoofer signal from channels of your system other than the left/right channels, then connect the output(s) of that unit to the “Bridge In”... -
Page 5: Speaker Polarity
Left Bridge In Right Bridge Remote S /N Power Model THIEL Audio INPUTS Lexington , Kentucky www.thie laudio.co SI 1 OUTPUT S To Subwoofer To main loudspeakers Speaker level Inputs L – R – Augment mode, line level input Speaker level Inputs L –... -
Page 6: Adjusting The Integrator
Crossover Mono Stereo [1 to 16] [in dB, 20 to 40] This display show the current setting of the selected parameter or which preset is currently being used. THIEL MAIN SPEAKERS Type Sealed Reflex Low Frequency Limit Sensitivity Damping SmartS... -
Page 7: Main Speaker Parameters
Main Speaker Parameters Type [Sealed or Reflex] Sealed should be selected if the main speakers are a sealed or “closed” design. Reflex should be selected if the main speakers are a ported or passive radiator design. Low Frequency Limit [in Hz, from 20 to 90] This parameter should be set to the main speaker’s “minus 3 dB”... -
Page 10: Integrator Parameters For Thiel Speakers
Integrator Parameters for THIEL Speakers Visit www.thielaudio.com\subsetup.cfm for information about parameter settings for most speakers, regardless of brand. Model Type Low Frequency Limit CS1.6 Reflex CS2.4 Reflex CS3.6 Reflex Reflex CS7.2 Reflex MCS1 Reflex Reflex SCS3 Reflex PowerPoint Sealed PowerPlane... -
Page 11: Maintenance
Maintenance Remote Control Battery Replacement The green light on the front of the Remote Control should light when any of the buttons are pushed. If it does not the batteries need to be replaced. Access the batteries by removing the four screws on the front of the unit using the hex driver provided, and lifting off the front cover (see illustration below). -
Page 12: Specifications
THIEL warrants every THIEL model SI1 system against defects in materials and workmanship to the original owner for a period of ten years from the date of purchase. THIEL will, at no charge, replace any defective part and make any repairs necessary to ensure its proper performance when the defective unit is returned to us postpaid. -
Page 13: Remote Control Command Codes
Remote Control Command Codes This information is provided for developers of automated systems. It is not relevant to most users. Function Allowed RS-232 code * RC5 code (Dec) values (## = values) Next SS00NT Previous SS00PV Increase SS00IC Decrease SS00DC Store# 0-6 ‡... - Page 16 THIEL 1026 Nandino Blvd., Lexington, KY 40511 Tel: 859-254-9427 • Fax: 859-254-0075 • Email: mail@thielaudio.com • www.thielaudio.com 7/05...