1. Manuals
  2. Brands
  3. MPC Manuals
  4. Toy
  5. STAR WARS HAN SOLO'S MILLENNIUM FALCON...
  6. Quick start manual

MPC STAR WARS HAN SOLO'S MILLENNIUM FALCON MPC953/06 Quick Start Manual

Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
HAN SOLO'S
MILLENNIUM
FALCON
™
™
™
MPC953/06
IMPORTANT! READ
THESE INSTRUCTIONS FIRST
Before you begin building your kit
read the instructions completely
and carefully. Study all the illustra-
tions and the placement of each
part. When assembling the kit test
fit each part before cementing.
This kit utilizes a combination of
vintage tooling and new parts.
Some gaps or seams may require
putty to close especially if lighting
the model. It is best to cut the
parts from their "runners" with a
modelers knife instead of twisting
them off. Cut the parts only as
they're needed. Only paint and
cement for styrene plastic should
be used. Be sure to trim off excess
plastic or "flash". Cement should
be applied to small parts with a
toothpick. Each part is numbered.
Placement for the part is some-
times numbered to correspond to
the part.
10
STEP NUMBERS
37
PART NUMBERS
CEMENT
DO NOT CEMENT
CLEAR
CLEAR
PLASTIC PARTS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the STAR WARS HAN SOLO'S MILLENNIUM FALCON MPC953/06 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for MPC STAR WARS HAN SOLO'S MILLENNIUM FALCON MPC953/06

Summary of Contents for MPC STAR WARS HAN SOLO'S MILLENNIUM FALCON MPC953/06

  • Page 1 MPC953/06 ™ IMPORTANT! READ THESE INSTRUCTIONS FIRST HAN SOLO’S ™ Before you begin building your kit MILLENNIUM read the instructions completely and carefully. Study all the illustra- tions and the placement of each part. When assembling the kit test FALCON fit each part before cementing.

  • Page 2: Front Landing Gear Installation

    LOCATING PINS INSERTS (BOTTOM HALF) Remove from both hull parts. FRONT LANDING GEAR INSTALLATION FRONT LANDING GEAR ASSEMBLY Allow cement to dry before pushing in landing gear. Apply cement carefully Do not cement Do not cement Do not cement Remove landing gear to close landing gear doors.
  • Page 3 REAR LANDING GEAR REAR LANDING GEAR ASSEMBLY INSTALLATION Repeat for other side. Reverse parts 51 and 52. This completes the left rear landing gear. Repeat steps 1 thru 5 for Do not cement right rear landing gear, but reverse item number 54. Do not cement Allow cement to dry, before pushing in...

  • Page 4: Cockpit Assembly

    COCKPIT & FIGURE ASSEMBLY COCKPIT ASSEMBLY NOTE: Item 4 installed with smooth side forward Clear Choose to hand-paint the cockpit wall details or apply the supplied decal. (not decal details will not match part) LANDING RAMP INSTALLATION LANDING RAMP ASSEMBLY Clear Do not cement Do not cement...

  • Page 5: Side Panel Installation

    SIDE PANEL INSTALLATION Be sure to putty all seams if lighting model. NOTE: Wall parts must rest against ribs on hull Clear Clear NOTE: Wall parts must rest against ribs...
  • Page 6 INSERTS (TOP HALF) RADAR ASSEMBLY RADAR NOTE: After radar assembly INSTALLATION and item 30 are installed, cement carefully from bottom Radar unit should pivot freely. Do not cement Do not cement Cement here only Radar assembly pushes into part 30.

  • Page 7: Hull Assembly

    HULL ASSEMBLY NOTE: Align pins inside the model as the two halves are joined. DOCKING RING COCKPIT INSTALLATION INSTALLATION Repeat steps 1, 2, & 3 for other side.
  • Page 8 Look out for more model kits from...

Table of Contents

Save PDF