Advertisement
Quick Links
SHOP PRESS
ASSEMBLY INSTRUCTIONS
CP500 - 50 TON MANUAL SHOP PRESS WITH WINCH
PRESS SPECIFICATIONS
Arcan Model No.
A
CP500
74"
A - Total Height
B - Inside Width
C - Press Feet Length
D - Bed Width
E - Stroke (ram travel distance from fully retracted position to fully extended position)
F - Pin Diameter
G - PB Winch
H - Sliding Head
I - Press Plates Included
P.O. Box 58
B
C
35"
29.75"
Travelers Rest, SC 29690
D
E
13"
6.75"
Phone: (800) 879-7316
F
G
H
1.25"
Y
Y
Fax: (864) 834-0073
© Copyright 2007, Arcan Professional Tools
I
Y(2)
Advertisement
Related Manuals for Arcan CP500
Summary of Contents for Arcan CP500
- Page 1 SHOP PRESS ASSEMBLY INSTRUCTIONS CP500 - 50 TON MANUAL SHOP PRESS WITH WINCH PRESS SPECIFICATIONS Arcan Model No. CP500 74" 35" 29.75" 13" 6.75" 1.25" Y(2) A - Total Height B - Inside Width C - Press Feet Length D - Bed Width...
- Page 2 We want to know if you have any problems with our products. • Release hydraulic pressure before loosening any fittings. If you are missing any parts or find any damage, call Arcan directly, • Maintain proper hydraulic fluid levels. and we will remedy the situation. Please do not call the store where •...
- Page 3 Bearing Shield - 1 Accessory only - Not needed for assembly Washers - 8 TOOLS NEEDED 1-1/4" x 14" Press Pins - 4 3/4" and 1/2" sockets and wrenches Examine box contents, then proceed with the following instructions. CP500 Operation Manual...
- Page 4 Wear safety gloves and safety goggles. Note: Position press feet on each side of the press. Attach one bolt, washer and nut on each side. Bolts should be attached OFFSET from one another. Front view CP500 Operation Manual...
- Page 5 Front view WARNING Note: When sliding bed to frame Bed must be at the BOTTOM of the frame bottom, DO NOT use bed handles. before proceeding to the next step. Slide bed down to bottom of frame CP500 Operation Manual...
- Page 6 ALL FOUR (4) pins must be COMPLETELY through BOTH SIDES of frame in order to operate press. Let bed rest on inserted pins Place 3rd and 4th pin on each side Secure pins completely through bed and frame. CP500 Operation Manual...
- Page 7 See Step 6. on to mounting the pump assembly. WARNING Hose must be on the OUTSIDE of ram frame, or it will NOT be mountable to the press. CP500 Operation Manual...
- Page 8 Attach bolts up through ram frame to matching holes in press. Hand tighten. Wrench tighten This end up after both bolts have been installed. Ram is now able to slide left and right within ram frame. CP500 Operation Manual...
- Page 9 PRESSURE CRADLE. Pump ram Ram will retract as against press plates until gauge against press plates until gauge Do not allow the ram to pressure is released. reads "5 Tons". reads "10 Tons". extend more than 5.5". CP500 Operation Manual...
- Page 10 CAUTION DO NOT TURN RELEASE VALVE MORE THAN ONE FULL TURN or equipment may be disabled. CP500 Operation Manual...
- Page 11 1. Move press bed into LOWEST position 3. Thread the BARE end of the LONGER so it is resting on top of pins 1 and 2. of the two steel cables up and through DO NOT FULLY TIGHTEN. the pump bracket. CP500 Operation Manual...
- Page 12 It may be necessary to repeat this leveling with our products. If you are missing any parts procedure in the future. or find any damage, call Arcan directly, and we will remedy the situation. Please do not call the store where you purchased this product.
- Page 14 * 3-3/16" Seal SHCS 7/16 14 x 1/2" SHCS 7/16 14 x 3/4" * Light Spring * Heavy Spring 7/16" Split Lock Washer Pump Filter Pump Fitting 1/4" MNPT 7/16" JICF 7/8" Grip Handle for Pump * O-Ring CP500 Operation Manual...
- Page 15 NOTES CP401 Operation Manual CP500 Operation Manual...
- Page 16 NOTES CP401 Operation Manual CP500 Operation Manual...
Need help?
Do you have a question about the CP500 and is the answer not in the manual?
Questions and answers