Table of Contents
Advertisement
Quick Links
Spinnit
FMMH 2
R
USER'S MANUAL
Before operating this equipment, please read these
instructions completely and keep these operating
instructions for future reference.
-
Hydraulic Paper Drill
485 Hague Street, Rochester, NY 14606 U.S.A.
Tel: 585-436-1934
www.lasscowizer.com
Serial Number:
Date of Purchase:
Dealer:
Address:
Telephone Number:
Fax: 585-464-8665
info@lasscowizer.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Lassco Wizer Spinnit FMMH-3
Summary of Contents for Lassco Wizer Spinnit FMMH-3
- Page 1 Spinnit FMMH 2 Hydraulic Paper Drill USER’S MANUAL Serial Number: Date of Purchase: Dealer: Address: Before operating this equipment, please read these instructions completely and keep these operating instructions for future reference. Telephone Number: 485 Hague Street, Rochester, NY 14606 U.S.A. Tel: 585-436-1934 Fax: 585-464-8665 www.lasscowizer.com...
-
Page 2: Table Of Contents
Table Of Contents 1 - Introduction 1 - Introduction 1.1 - Your New FMMH-2 Paper Drill Your New FMMH-2 Paper Drill....Page 01 Thank you for your purchase of the Spinnit FMMH-2 Shipping Damage Inspection....Page 01 Paper Drill. We ask that you take a moment to fill in the serial 2 - Safety number and other information on the front cover of the Safety Instructions........ -
Page 3: Safety
2 - Safety 2.1 - Safety Instructions All operators must read and understand the Users KEEP CHILDREN AWAY. All visitors should be kept a safe Manual including all safety instructions before using this distance from the work area. equipment. Failure to fully understand the safety instructions can result in personal injury. -
Page 4: Warning Labels
2 - Safety 2.2 - Warning Labels WARNING: DO NOT EXPOSE TO RAIN OR USE IN DAMP LOCATIONS. Page 03... -
Page 5: Grounding Instructions
2.3 - Grounding Instructions Diagram 2-10 METAL SCREW COVER OF GROUNDED OUTLET BOX GROUNDING In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to re- duce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conduc- tor and a grounding plug. -
Page 6: Setting Up Your Machine
3 - Setting Up Your Machine 3.1 - Loose Items Inventory Please remove and inspect the following items: FMM6-651A: Master Chip FMM6-652A: Chip Bag MS-1: Drill Sharpener (1) CC-2: Chip Clearer (1) Chute (1) Assembly (1) (this item may be installed) Hollow Drill Bits (2) EBM-32: Chuck Re- FMM9-957A: Spindle... -
Page 7: Uncrating And Removing From The Pallet
3 - Setting Up Your Machine 3.3 - Uncrating and Removing From the Pallet 3.3.1 Remove the wooden framing around the outside box. 3.3.2 Remove the box up and over the machine. 3.3.3 Remove the two (2) 5/16” bolts which are securing the machine to the pallet: access through the rear of the machine using a 5/16”... -
Page 8: Adding The Oil
3 - Setting Up Your Machine 3.5 - Adding the Oil 3.5.1 Remove the back cover by unscrewing the eight (8) hex screws that hold it in place. 3.5.2 Remove the Cap on the Oil Tank. 3.5.3 Insert the Plastic Funnel, included with the machine, into the Oil Tank and, using the new batch of Hydrol HL Oil (HL3HY) included with the machine, fill the tank with 1-1/2 gallons or until the Oil Tank is approximately 3/4 filled with oil. -
Page 9: Attaching The Paper Side Stops
3 - Setting Up Your Machine 3.6 - Attaching the Paper Side Stops 3.6.1 Attach the Paper Side Stops using two (2) Side Stop Screws Diagram 3-30 (FM4-4007) each. Position the Paper Side Stop as desired and tighten down with light pressure. Side Stop Screws Paper Side Stop Table... -
Page 10: Operation
4 - Operation 4.1 - Protective Guard 4.1.1 Your FMMH-2 comes with a protective guard installed. DO NOT Diagram 4-10 operate this machine without the guard in place. 4.1.2 Please note that when you are performing certain operations such as removing and installing drill bits, you will need to move the guard out of the way. -
Page 11: Leveling The Drill Bits
4 - Operation 4.3 - Leveling the Drill Bits Diagram 4-40 BEFORE LEVELING THE DRILL BITS, 1/8” Hex Wrench MAKE SURE THAT THE DRILL MOTOR Access Guard Screw SWITCH IS IN THE OFF POSITION. Access Guard 4.3.1 We recommend using a piece of card stock on the Table when leveling the drill bits to avoid drilling into the drill strip. -
Page 12: Adjusting The Back-Gauge Assembly
4 - Operation 4.4 - Adjusting the Back-Gauge Assembly 4.4.1 Adjust the Back-gauge so that it is the correct distance from the edge of the product to the center of the hole to be drilled by per- forming the following: 4.4.2 Loosen the Clamp Knob on the right side of the Back-gauge. -
Page 13: Drilling Procedures
4 - Operation 4.6 - Drilling Procedures 4.6.1 After all your adjustments are made as desired, position the Table Diagram 4-100 in its primary position. Set the product to be drilled on the table and make sure it is secure using the Paper Side Stops. To drill, step down on the Foot Pedal and hold, raising the Table up to meet the drill bits. -
Page 14: Maintenance
5 - Maintenance 5.1 - Safety ALWAYS DISCONNECT THE POWER BEFORE PERFORMING THE FOLLOWING MAINTENANCE ON THIS MACHINE. MAINTENANCE SHOULD ONLY BE PER- FORMED BY A QUALIFIED TECHNICIAN. KEEP HANDS CLEAR WHILE PERFORMING MAINTENANCE ON THIS MACHINE. MOVING PARTS CAN CRUSH AND CUT. 5.2 - Annual Lubrication 5.2.1 Lubricating your FMMH-2 should be done at least once every 12... -
Page 15: Inspecting The Flex Drive
5 - Maintenance 5.3 - Inspecting the Flex Drive 5.3.1 Inspecting the Flex Drive on your FMMH-2 should be done at Diagram 5-40 least once every 12 months; however, it may be necessary to check this more often if problems with the rotation of the spindles is noticed. -
Page 16: Changing The Hydraulic Oil
5.4.1 When using Lassco Wizer Hydrol HL, the Hydraulic Oil should be changed every 2100 Machine Hours. Machine Hours are defined as the period of time that the Table Motor is turned on and pumping oil, regardless of being oper- ated or not (Even when not drilling, the Table Motor is pumping oil continuously). -
Page 17: Funnel
5 - Maintenance 5.4 - Changing the Hydraulic Oil 5.4.6 Insert the included Plastic Funnel into the Oil Tank and, using a new batch of Hydrol HL Oil (HL3HY) or an equivalent brand, fill the tank with 1-1/2 gallons or until the Oil Tank is approximately 3/4 filled with oil. 5.4.7 Replace the Cap making sure it is sealed securly. -
Page 18: Trouble Shooting Guide
6 - Trouble Shooting Guide 6.1 - Determining the Cause and Correction to Certain Problems Problem Cause Correction Drill bit not concentric. Foreign material in chuck or in Inspect and clean. drill plug. Drill bit is bent. Replace drill bit. Drill bit not seated in chuck Re-insert drill bit correctly. - Page 19 6 - Trouble Shooting Guide 6.1 - Determining the Cause and Correction to Certain Problems Problem Cause Correction The machine is not level on the Use the leveling feet to make the Machine vibrates, wobbles, resonates, etc. floor. machine level on the floor. See Setting Up Your Machine.
-
Page 20: Parts Diagrams
7 - Parts Diagrams 7.1 - Side View Page 19... -
Page 21: Head Assembly
7 - Parts Diagrams 7.2 - Head Assembly Page 20... -
Page 22: Spindle And Chuck Assembly
7 - Parts Diagrams 7.3 - Spindle and Chuck Assembly Page 21... -
Page 23: Rear View
7 - Parts Diagrams 7.4 - Rear View Page 22... -
Page 24: Parts List
7 - Parts Diagrams 7.5 - Parts List FMM9-9534: Motor FMH-4000: Table FMM9-9530: Drive Belt FMH-3017: Safety Apron FMH-3018: Table Bolster FMM8-8504: Hand Wheel FM3-3004: Die Pin FMM8-8508: Hand Wheel Lock Knob FM7-7002: Backgauge Clamping Bracket FMM9-9517: Shroud Locking Knob FM3-3007: Pin Housing FMM8-8503: Traverse Lead Screw FMH-2014: Hydraulic Cylinder...
Need help?
Do you have a question about the Spinnit FMMH-3 and is the answer not in the manual?
Questions and answers