Related Manuals for Classic Exhibits Perfect 10 VK-1506
Summary of Contents for Classic Exhibits Perfect 10 VK-1506
- Page 1 Step 1 Order #XXXXX - P10 - VK-1506 Gia - General Layout 866.652.2100 10’ Plan View Perspective View 10’ WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING © 2014 w w w . c l a s s i c e x h i b i t s . c o m patent D599,121 Page 1 of 6...
- Page 2 Step 1 Order #XXXXX - P10 - Gia - Backwall Assembly 866.652.2100 Item Qty. Description Steps: Left Leg Assembly NOTE: Assembly may be easiest if assembled face down on floor then lifted upright. Middle Leg Assembly 1) Connect upper curved vertical extrusions [3a,3,6] to leg assemblies [1,2,5]. NOTE: When assembling horizontals they should be Upper Curved Vertical 2) Connect lower and upper horizontal extrusions between vertical assemblies by slightly...
- Page 3 Step 2 Order #XXXXX - P10 - Gia - Blade Attachment 866.652.2100 Decorative Blade Attachment (if accidently removed) Slide A10 Clamp into groove of square extrusion. When desired location is found, tighten set screw to secure. Attach decorative wing and blades to A10’s attached to Set- Screw...
- Page 4 Step 3 Order #XXXXX - P10 - Gia - Backwall Attachments 866.652.2100 Light Connection Accessary Attachment Attach lights to Attach header support to backwall then backwall where attach header to support with velcro. desired and tighten in place. Header Header Cubby Attachment Shelf attaches to section Shelf attaches to back of...
- Page 5 Step 4 Order #XXXXX - P10 - Workstation Assembly 866.652.2100 Part Number Description Left Leg Assembly Right Leg Assembly Horizontal Extrusion Horiontal Extrusion w/ Door Stopper D (w/ Door Stopper) Knobs face INSIDE of workstation Steps: 1) Connect lower horizontal extrusion [C] between bottom of leg assemblies [A and B] as shown. 2) Insert Laminated infill into grooves of leg assemblies [A and B].
- Page 6 Step 5 Order #XXXXX - P10 - Workstation Assembly (Cont’d) 866.652.2100 Part Number Description Horizontal Extrusion Horizontal Extrusion Place internal shelf into Steps: workstation then 1) Attach horizontal extrusion [E] between vertical leg assemblies [A and B] as shown below. place counter atop 2) Insert Laminated infill into grooves of vertical leg assemblies [A and B].
- Page 7 Step 6 Order #XXXXX - P10 - Workstation Assembly (Cont’d) 866.652.2100 Part Number Description Curved Montior Mount Extrusion Steps: 1) Slide connection bar into lower leg assembly. Slide upper vertical over bar and secure both. 2) Attach monitor mount to vertical as shown in detail below. Monitor Mount Attachment NOTE: Monitor mount should be installed while laying down on floor...
- Page 8 Case Packing - Case 1 of 3 Order #XXXXX - P10 - 866.652.2100 Vertical Connection Bar A10’s Attached Header A10’s Attached Header Supports Level 1 Level 5 Level 4 Level 2 Level 3 Vertical Connection Bar Additional Items: - Setup Hardware - Graphic - (3) Lights WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING...
- Page 9 Order #XXXXX - P10 - Case Packing - Case 2 of 3 866.652.2100 Top View Backside Shelf Cubby Level 1 WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING © 2014 w w w . c l a s s i c e x h i b i t s . c o m patent D599,121...
- Page 10 Order #XXXXX - P10 - Case Packing - Case 3 of 3 866.652.2100 Top View of Each Level Horiz. Extrusion E Horiz. Extrusion F Internal Shelf Monitor Leg Assembly Leg Assembly Mount Inserts Counter Door Level 4 Level 1 Level 2 Level 3 Level 5 WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING...
Need help?
Do you have a question about the Perfect 10 VK-1506 and is the answer not in the manual?
Questions and answers