Summary of Contents for Beijer Electronics X2 extreme 15 HP
Page 1
X2 extreme 15 HP English MAEN261B, 2021-11...
Page 2
The information in this document is subject to change without notice and is provided as available at the time of printing. Beijer Electronics AB, including all its group companies, reserves the right to change any information without updating this publication. Beijer Electronics AB, including all its group companies, assumes no responsibility for any errors that may appear in this document.
Toxic and hazardous materials or elements 零件描述 有毒和有害的材料或元素 Cr6+ PBDE PCB and electronic components PCB 和电子元件 O: Indicates that this toxic or hazardous substance contained in all of the homogenous materials for this part is below the limit requirement in SJ/T 11363–2014. Beijer Electronics, MAEN261B...
CE PRODUIT CONTIENT UNE PILE QUI NE PEUT PAS ÊTRE REMPLACÉE PAR L'UTILISATEUR. Warning: Explosion hazard! Substitution of components may impair suitability for Class I, Division 2. RISQUE D'EXPLOSION! LA SUBSTITUTION DE COMPOSANTS PEUT NUIRE À LA CONFORMITÉ DE CLASSE I, DIVISION 2. Beijer Electronics, MAEN261B...
In a Zone 22 environment, this equipment shall be installed in an enclosure that provides a degree of protection not less than IP64 in accordance with IEC/EN 60079-0. The IP rating of the equipment is limited to the IP rating of the enclosure it is to be installed into. Beijer Electronics, MAEN261B...
• Clean the display and surrounding front cover with a soft cloth and mild detergent. • The battery must be replaced by an authorized Beijer Electronics service center. 1.9.1 Cleaning the Display We recommend using a dry, clean cloth to wipe off dust regularly. Use alcohol or ammonia-based cleaning agent for cleaning only when necessary.
The layer structure of the touch screen contains air. In rare cases, the appearance of bubbles can arise. This is purely cosmetic and does not affect the functionality of the operator panel. The appearance can occur under certain environmental conditions such as temperature, humidity, and atmospheric pressure. Beijer Electronics, MAEN261B...
2. To cut a correct opening for the operator panel, use the cut out dimensions in the outline drawing. A separate cut out drawing is available for download from the Beijer Electronics web site. For more information, see sections Operator Panel Drawings Technical Data.
Page 11
flatness < 1 mm overall and < 0.05 mm/mm with a surface roughness, Ra < 1.6 μm 7. Installation to be through an EPL (Db)(Dc) enclosure for the applicable Dust Group, Temperature classification and Ambient temperature range. Beijer Electronics, MAEN261B...
3.2.1 Connections to the Controller For information about the cables to be used when connecting the operator panel to the controller, please refer to the help file for the driver in question. Beijer Electronics, MAEN261B...
Connect the desired cables and attach them to strain relief plate with cable ties provided. 3.2.3 Other Connections and Peripherals Cables, peripheral equipment and accessories must be suitable for the application and its environment. For further details or recommendations, please refer to the supplier. Beijer Electronics, MAEN261B...
Technical Data Technical Data Parameter X2 extreme 15 HP Front panel, W × H × D 411 × 286 × 7 mm Cut out dimensions, Maximum corner radius: 4 mm. 394 x 270 mm. W × H Mounting depth 66 mm (166 mm including clearance)
ATTENTION: Serial COM B is not supported if RS-422 has been chosen for COM A. Compass Safe Distance Variant Condition Standard Steering Compass Compass X2 extreme 15 HP (SC) Non-energized 60 cm 45 cm Non-energized after 70 cm 50 cm magnetization...
Phenol Xylene Ammonia, conc. Sodium hydroxide 5% 97 octane unleaded petrol Ethyl acetate Sodium hydroxide 30% 98 octane leaded petrol Touch Screen and Overlay Material 5.2.1 Protective Film Autoflex EBA 180L covers the overlay surrounding the screen. Beijer Electronics, MAEN261B...
Page 17
The Autoflex protective film is not resistant to high pressure steam at over 100 °C or the following chemicals: Concentrated mineral acids Benzyl alcohol Concentrated caustic solution Methylene chloride Beijer Electronics, MAEN261B...
5.2.3 Touch Screen Protector For harsh environments and exposure to outdoor conditions, it is recommended to use a protective film to guard the touch screen from damage. This optional part can be ordered from Beijer Electronics. Beijer Electronics, MAEN261B...
RS232 RxD RS232 TxD RS422 Tx- CAN-L RS485 Tx-/Rx- RS232 RTS RS232 CTS RS422 Rx- The connector supports up to two independent serial communication channels and can be configured for RS-232, and RS-422 or RS-485 or CAN. Beijer Electronics, MAEN261B...
Page 20
Operator Panel Drawings COM B D-sub-9, female COM 3 RS-485 Tx+/Rx+ CAN-H TERM+ TERM+ RS-485 Tx-/Rx- CAN-L TERM- TERM- The connector supports galvanic isolated RS-485 or CAN. Beijer Electronics, MAEN261B...
3 turns around the ferrite core provide 9 times the suppression of 1 turn. Connect a wire or grounding braid, that is sized correctly according to local electrical codes, between the chassis of the operator panel and the closest grounding point. Beijer Electronics, MAEN261B...
1. Check whether the other Ethernet unit has its shield directly grounded or grounded via a capacitor. Note: In many cases, connecting the shielded Ethernet cabling to the chassis at both ends is inappropriate. Hum or grounding loops can occur. Unshielded cabling may even result in fewer communication errors. Beijer Electronics, MAEN261B...
This connects the HF transients to ground. To Achieve Better EMC Protection • Initially, use the original cabling from Beijer Electronics primarily. • Place the 24 V DC and communications cabling in one cable trunk/cable duct and 230/380 V AC in another. If the cables need to be crossed, cross them at 90°...
Install the fan so that it sits in a cooler area and blows cold air against the operator panel. If the fan is mounted at the top and sucks warm air upwards, the ambient temperature of the fan becomes higher, resulting in a shorter lifespan. Beijer Electronics, MAEN261B...
Page 27
This is assuming that all supplied power is transformed to heat. Note: Please ensure that the temperature will not exceed the maximum ambient operating temperature in the enclosure. This can be influenced by other heat generating devices. Beijer Electronics, MAEN261B...
Transients on the 24 V feed are connected to the ground. • No risk that the 24 V feed is at a high level in relationship to the ground. This is not unusual since there is high static electricity. Beijer Electronics, MAEN261B...
Use external units to improve communication and achieve galvanic isolation. Westermo has good industry-standard insulators that are also insulated from the 24 V DC feed. Beijer Electronics, MAEN261B...
Page 30
24 V feed, disturbances and grounding currents from the 0 V on the 24 V side disrupt the communication. Using this type of unit solves one problem but creates a larger problem! A substandard installation may work now, but problems may arise when other devices are connected. Beijer Electronics, MAEN261B...
CAN nodes with 118 Ohm... 130 Ohm resistors. The recommended resistor value is 120 Ohm/1%/0.25W on each end. • Place the termination resistor near the CAN bus connector (as close as possible). • This product has no integrated termination resistors. They must be added externally. Beijer Electronics, MAEN261B...
Use the screensaver functionality (see SW manual). • Changing constantly between static and dynamic images. • Avoid excessive brightness differences between foreground and background elements. • Use colors with similar brightness. • Use complementary colors in follow-up images. Beijer Electronics, MAEN261B...
Page 33
Head office Beijer Electronics AB Box 426 201 24 Malmö, Sweden www.beijerelectronics.com / +46 40 358600...