PZRacing P2-Tronic PA601 User Manual

Puoi trovare l'ultima versione del manuale, manuali applicativi, video tutorial e manuali in altre lingue, cliccando sul
link di seguito o scannerizzando il QR code a lato
You can find the latest version of the manual, application notes, video tutorial and manuals in other languages,
clicking on the link below or scanning the QR code on the side

Installation

Remove the front fairing of the motorcycle to access the rear connector of the dashboard.
Disconnect the motorcycle harness connector (34pin connector) from the dashboard and connect the male/female P2-Tronic connectors to the
dashboard and to the main harness connector.

GPS receiver installation

N.B: do not place cameras or other sources of electromagnetic interference near the receiver to avoid the GPS signal being
disturbed
Place the receiver module with the writing facing upwards and in a horizontal position with a clear and unobstructed view of the sky, it is
recommended to place on the steering plate as horizontal as possible trying to avoid that is facing the pilot.
The tank and the lateral air intakes of the motorcycle are highly not recommended as the GPS receiver would be completely
covered by the chest and head of the rider and also during a turn the GPS receiver would be completely obscured by the motorcycle
itself.
Use the junction connectors to route the wire along the main harness, fix the entire length of the sensor cable, make sure that the cable is not under
tension when using the device.
N.B: the GPS receiver must be connected, otherwise the handlebar switch of the bike will not work

Usage

N.B: to be able to reveal the lap times you must activate the lap timer on the dash.

Lap time activation (LAP Off / On) on the dashboard

This function is present only in the TRACK display mode (modify the "Info mode" within the setting of your "Riding Mode", see the motorcycle user
manual).
To activate the LAP function in the Functions Menu, scroll through the available functions using the "Up" and "Down" arrows of the "Mode/Enter"
button on the left-handlebar switch until the "LAP" item is displayed.
To activate/deactivate it, press the "Mode/Enter" button, when the LAP is active, the instrument panel displays the word "LAP ON".

Start session

The receiver works fully automatically, turns on when the vehicle is turned on, hooks up to the satellites and loads the correct track automatically, then
after the vehicle has started it will start showing the lap time on the motorcycle dashboard and memorizing the data if the function has been activated.
Below is the legend of the product status via the receiver LED:
- Solid: Wi-Fi on, GPS receiver not ready. The signal which is being received is not strong enough to locate the position. If a long period of time has
passed or if you have travelled several kilometres from the place you last switched on the device, you have to wait up to 4-5 minutes to receive a signal;
otherwise one minute is necessary to locate the position. If the led does not change status, position the receiver in a less restricted area because it
couldn't receive a good signal.
- Slow blink (1S off, 1S on): Wi-Fi on, GPS receiver ready. You can start your session.
- Fast blink (400mS off, 100mS on): Wi-Fi off, motorbike moving. After the bike has started and has reached 30Km/h for 5 seconds, the Wi-Fi is
turned off and the receiver will be ready to show the lap time on the dashboard.
N.B: if your circuit is not in memory send an email to
firmware update with your track

Wi-Fi

The GPS receiver is equipped with an integrated Wi-Fi
module that will be used for data download and settings
related to storage. Wi-Fi turns on when the product is
turned on and turns off when the motorcycle exceeds
30Km/h, to reactivate the Wi-Fi it will be necessary to
turn off and on the GPS receiver.
The default data for the Wi-Fi network are the following:
Network name: PZRacing S600-USER 1
Password: 12345678
PZRacing Via de Gasperi 5 – 61032 Fano (PU) Italy - Tel: +39 0721 820434 – Email: tech@pzracing.it
http s ://pzracing.it/ download /
tech@pzracing.it with the name and location of the circuit, we will send you a
P2-Tronic PA601
User Manual - v1.0 – 18/07/23