Tekkeon ezTalker ET1000 User Manual

T by Tekkeon is a sleek cord-free headset that enables
EZ ALKER
comfortable handsfree communication with your mobile phone.
1000 works with your Bluetooth-ready mobile phone to provide clear,
high-quality communication.
While using your T headset, you can store your mobile phone in
EZ ALKER
your pocket, backpack, or briefcasejust about anywhere in close
proximity that is convenient for you.
Unpacking T
EZ ALKER
Your ezTalker package includes
the following:
! ezTalker Headset
" Charging cradle with belt clip
# Charger
% ezEarhook
& ezFit Ring
' Comfort Pad
( User guide
(not shown)
Getting to Know T
EZ ALKER
TALK Button
Used for turning headset on/off,
pairing, and making/receiving calls
Amber and Blue LEDs
Provides visual indication of headset
status: power on/off, pairing mode,
muting mode, charging mode, and low
battery
Volume Control
Used to adjust the speaker volume
and to mute the microphone
Microphone
Speaker

Getting Started

Before using ezTalker, you must:
Charge ezTalker
)
Pair ezTalker to your mobile phone
)
Fit ezTalker to your ear
)
Power ezTalker
)
Directions for each of these activities are provided in the following four
sections. Once these steps are completed, you will be ready to use
ezTalker!
ET1000
!
#
&
'
U S E R
Charging T
EZ
T
EZ ALKER
Before using ezTalker, you must charge the headset for approximately
two hours. When fully charged, the battery provides up to four hours of
talk time and up to 168 hours of standby time.
To Charge the Headset
1. Insert ezTalker into the charging cradle as
shown.
2. Plug the charger into the charging jack on
the right side of the charging cradle.
3. Plug the charger into a wall outlet.
headset is charging, the amber LED on the
headset will remain on. When the headset is
fully charged, the amber LED will turn off.
"
4. Unplug the charger cable from the wall outlet and the charging
cradle.
%
BATTERY INDICATION
capacity), the amber LED will flash and you'll hear a double beep every
32 seconds.
Pairing T
EZ ALKER
Pairing is the process of linking the headset with your Bluetooth mobile
phone. Before using ezTalker with your mobile phone you must pair the
devices. After this process is complete, you can use the headset only
with its paired mobile phone. To use ezTalker with a different mobile
phone, you must repeat the pairing process with the new mobile phone.
In this case, the headset will no longer work with the original mobile
phone.
BEFORE YOU PAIR THE HEADSET
REVIEW THE INSTRUCTIONS IN YOUR MOBILE PHONE USER GUIDE FOR PAIRING YOUR
MOBILE PHONE TO A BLUETOOTH HEADSET
To Pair the Devices
1. Turn on the mobile phone and place it within 10 feet of the headset.
2. Initiate the Bluetooth device-pairing (discovery) feature on the
mobile phone. Refer to the mobile phone user guide for
instructions on initiating this feature.
3. With the headset turned off, press and hold the TALK button
approximately five seconds, until the blue and amber LEDs flash
alternately or until you hear the PAIRING tone.
4. Release the TALK button.
5. Follow the mobile phone prompts, and when prompted for the
passkey (also called passcode or BT PIN), enter 0000 (the ezTalker
When pairing is complete, the headset will be placed in
passkey).
Standby Mode, ready to make and receive calls, the amber LED
will turn off, and the blue LED will flash at two-second intervals.
G U I D E
ALKER
While the
: When the battery is low (less than 10% of
to Your Mobile Phone
,
ENSURE THAT THE BATTERY IS FULLY CHARGED
.
The headset is now in Pairing Mode
Figure 1.
ezTalker inserted into
charging cradle
,
AND
.
1