Inateck PR02001 - 4x6 Shipping Label Printer with Stand Manual

To Check the Content in the Package

Illustration of the Main Parts

1. Movable paper conveyance device
2. Power interface
3. USB interface
4. Glue stick
5. Printhead
6. Opening button
7. Form feed button/Indicator
8. Paper inlet
9. Power switch

Note: Power Switch
Press down the power switch to "|" turn on the printer.

Press down the power switch to "O" to turn off the printer.

Please use the original power adapter that comes with the package to avoid unsatisfactory printing result or damage to the printer.

How to Use

It is dangerous to plug in/out the power cable to/from power source when the switch of the printer is at "ON" status. Do not stop a working printer by plugging out its power cable, as it might damage the internal circuits and the printing result.

1. Make sure the power switch is at "Off" status and then connect the printer to power source.
   
2. Connect the printer to computer by using the USB cable.
   
3. Press down the power switch to "|" turn on the printer.
   
4. Insert the folded paper through the inlet of the printer or open its top and then put papers in.
   Method 1
   
   Method 2
   
   Note: If you open the printer by method 2, the printer will automatically output a blank paper.

Installation of Driver

In the USB flash drive users can find the drive and its installation instruction (for both Mac and Windows). They are also available on the official site www.inateck.com.

Functions of Form Feed Button

1. Skip a blank label
   When under standby mode and the paper is installed properly, press the form feed button and the printer will skip a blank label automatically.
2. Auto-recognition of paper type (label/bill)
   1. Power off the printer;
   2. Open the top of the printer and put paper into it. Close the top and power on the printer.
   3. After the initialization of the printer, which takes around 3-5 seconds, press the form feed button and hold until a "beep" sound is heard. The printer will then recognize the paper type automatically.
   4. In the printer preferences, set the paper type to continuous paper
3. To print self-test page
   When under standby mode with paper properly installed, press the form feed button and hold. A "beep" sound will be heard. Go on holding until another two sounds of "beep" are heard. After releasing the form feed button, the printer will print a self-test page.

Indicator Status and Trouble Shooting

Treatment for Jammed/Stuck Paper

Turn off the printer and open the top. Pull out the jammed/stuck paper from the inlet and install new one.

Be careful with possible scald. The temperature of printer is high when it just stops working.

Note:
If paper gets stuck, please check if there is any adhesive or dirt residue on the print head. If so, wipe them out with the alcohol cleaning pen included in the package. The printer can resume working when the alcohol gets dried.

The print head heats up when working. Please don't touch it, as well as the parts nearby, when the printer is working or just stops working.

FAQ

Q: There are blurs, white dots, or white lines on the printed label.
A: Please increase the print density, lower print speed or wipe the print head with alcohol cleaning pen (Please wipe the print head regularly to keep it clean.)

Q: The position of the print result is incorrect (not in the middle, deviates to left/right or up/down).
A: Check whether the paper is installed properly and whether the inlet clamp is clamping the paper closely.

Q: Why there is always a blank paper following a printed one?
A: If such situation occurs, please check whether the paper type is correctly set. You can set it as "auto-match" or "continuous form paper" under the settings "Printing Preferences" - "Paper/Quality" - "Paper Source".

Packing List

PR02001 * 1
Cleaning Pen * 1
Instruction Manual * 1
USB Flash Drive * 1
Paper Stand * 1
Thermal Label 4 x 6 inches * 1
Power Adapter * 1
USB Cable * 1
Instruction Manual of Direct Thermal Paper & Cleaning Pen & Stand * 1

Contact Us

Please feel free to email support@inateck.com if you have any query regarding Inateck PR02001. We will gladly assist you.