Shark HE400 - Air Purifier Manual

SETTING UP YOUR UNIT

Parts

1. Control Panel
2. Front Panel
3. Handles
4. Front Display
5. Air Vents
6. Purifier Base
7. Filter
8. Filter Cover
9. Remote Control

TIPS FOR SETTING UP YOUR UNIT

• Make sure the front panel of the unit faces away from the closest wall.
• Do not move the unit while it is running. Turn off the power and unplug the unit before moving it.
• Use the handles on the sides when lifting or moving the air purifier.
• Make sure the vents are not blocked.
• Do not place anything on the air purifier.
• Do not place the air purifier near heaters or radiators.
• Keep the unit out of direct sunlight and away from water or other liquid.
• Keep all nearby doors and windows closed when operating the air purifier.
• Avoid using in very humid environments.

SETUP

1. Before plugging in the unit for the first time, you must remove the filter and take it out of its packaging. First, remove the filter cover from the back of the unit. Press the tabs near the top and pull the cover toward you.
   
2. Remove the filter from the unit. Take the filter out of its sealed plastic packaging. To reinstall it, insert it into the unit.
   
3. With the filter installed, replace the filter cover. Insert the tabs on the bottom of the cover into the slots on the unit. Press the top of the cover, then the sides, until it clicks into place. DO NOT run the air purifier unless the filter is removed from its packaging and installed correctly.
   
4. Set up the unit upright on a level floor. For best results, set it up in the space you spend the most time in, such as the kitchen, living room, or bedroom. Make sure the unit is at least 3 inches (8cm) away from all walls, large objects, or electronics.
   
5. Plug the unit into an electrical outlet and press the power button on the top control panel or on the remote.
   
6. When the unit is powered on, it will begin to analyze the air quality indicated by the rotating lights. After a few seconds the unit will display the current air quality and you can customize the settings on your unit.
   

CONTROL PANEL

Your Air Purifier 4 is equipped with digital displays on both the top and front of the unit.

TOP CONTROL PANEL

Displays the current air quality status based on the AIR INFO option selected, and includes controls that allow you to customize the settings.

TOP CONTROL PANEL BUTTONS

On/Off: Press to turn the power on or off.

Air Info: Press to switch between air quality display options. See the Air Info Settings section for more information.

Auto Mode: Press to turn on Auto Mode. In this setting the fan speed automatically adjusts based on real time air quality readings. As the air quality improves, the fan speed will decrease. If air quality worsens, the fan speed will increase. Leave your unit in Auto Mode for optimal filter life and performance.

Filter Life: Press to show the remaining filter life in hours. Once the filter has 0 hours remaining, the FILTER LIFE button will flash to indicate the filter needs to be changed. See Installing and Removing the Filter section for more information.

Brightness: Adjusts the brightness of both the front display screen and the top control panel. Switch between 3 options: full brightness, partially dim, fully dim.

Shut-Off Timer: Set the number of hours for the air purifier to run before it automatically shuts off. Timer can be set between 1–12 hours.

Fan Speed: Adjusts the speed of the fan. Select one of 4 settings: 1 Low, 2 Medium, 3 High, 4 Maximum. Note: If fan speed is manually changed, auto mode will be deactivated. For tips on optimal fan setting, see Optimizing Fan Speed section.

FRONT DISPLAY SCREEN

Displays the current air quality status based on the Air Info mode selected on the top control panel.

REMOTE CONTROL

Your air purifier includes a remote control that can turn the power on or off, and adjust the settings.

USING THE REMOTE CONTROL

To use the remote control, aim it at the front display screen and press the buttons on the remote. The remote control has a range of 15 ft. (5 meters). For best results, make sure no obstacles are between the remote control and the display screen.

REMOTE CONTROL BATTERY

This remote uses a C R2025 3-volt replaceable battery. To replace the battery, follow the steps below.

1. With a Phillips-head screwdriver (not included) unscrew the battery tray on the back of the remote.
2. Slide out the battery tray.
3. Remove the old battery and dispose of it according to local regulations. Take additional caution to keep old battery out of reach of children.
4. Insert the new battery, making sure the polarities (+) (–) are oriented correctly.
5. Reinsert the battery tray and use the screw to completely secure it in place.

REMOTE CONTROL BUTTONS

1. On/Off: Turns the unit on/off.
2. Air Info: Switch between air quality display options.
3. Auto: Enables Auto Mode.
4. Brightness: Adjusts brightness.
5. Fan Speed: Adjusts fan speed.
6. Shut-Off Timer: Sets timer.

AIR INFO SETTINGS

The built-in sensor detects your air quality to give you real-time information. Use the AIR INFO button to switch between air quality display options.

UNDERSTANDING YOUR AIR QUALITY

The rings on the front and top displays will change color as your air quality changes, allowing you to easily monitor your air quality even when you are far from the unit.

A blue ring means your air quality is good, with a low level of particle concentration.

An amber ring means your air quality is fair, with a moderate level of particle concentration. For better results, increase fan speed or select Auto Mode.

A red ring means your air quality is poor, with a high level of particle concentration. For better results, increase fan speed or select Auto Mode.

Note: Air quality sensor uses a cumulative particle count across all particle sizes to determine air quality percentage.

OPTIMIZING FAN SPEED

Your air purifier is equipped with 4 fan speed settings. Adjust fan speed to optimize your cleaning performance.

DISPLAY	SPEED	BEST FOR
	1	Quiet Operation
	2	Reducing Odors
	3	Reducing Allergens
	4	Maximum Cleaning

INSTALLING AND REMOVING THE FILTER

NOTE: Always remove all protective packaging from the filter before installing.

When the filter timer has 0 hours remaining, the FILTER LIFE button on the top control panel will blink, indicating that it's time to install a new filter.

1. Turn off and unplug the unit before removing or installing filters.
2. Remove the back cover from the unit by pressing the tabs at the top (1), then pulling the cover toward you.
   
3. To remove the old filter, pull it out by the tabs at the top and bottom of the filter (2). Discard old filter in trash.
   
4. Remove all packaging and wrapping from the new filter.
5. Insert the new filter, then replace the filter cover. Insert the tabs on the bottom of the cover into the slots on the unit (3). Press the top of the cover, then the sides, until it clicks into place.
   
6. Plug the unit back in and turn on power. Calibration will begin.
7. After installing a new filter, press and hold the Filter Life button on the top control panel for 3 seconds to reset the timer. The unit will beep when the timer is activated.

Disposing of used filters

Filters can't be cleaned or recycled. After removing a used filter, wrap it in an airtight plastic bag for disposal. As an extra precaution, wear gloves when handling a dirty filter.

MAINTAINING YOUR AIR PURIFIER

NOTE: Always unplug the unit before doing any cleaning or maintenance.

Exterior Cleaning

For best results, clean the exterior of the unit every two months or as needed. Use a microfiber cloth to remove dust. To sanitize, wipe down the exterior with a microfiber cloth dampened with warm, soapy water. Avoid excess water and abrasive chemical cleaners to prevent damage.

To maximize your air purifier's filter life, we recommend flipping the direction of your filter every three months. This will help equalize and balance the distribution of captured particles throughout the filter allowing for extended usage.

Interior Cleaning

For best results, clean the interior of the unit every two months or as needed. Remove the filter cover, take out the filter, and use a vacuum cleaner or a microfiber cloth to remove dust and debris from the interior of the unit. DO NOT use abrasive chemical cleaners on the inside of the unit.

AVAILABLE ACCESSORIES

ORDER ADDITIONAL ACCESSORIES AND REPLACEMENT FILTERS

Additional accessories and replacement filters are available on sharkaccessories.com

Remote Control

Use the remote control to operate your air purifier from a distance.

SHARK™ AIR PURIFIER 4 ANTI-ALLERGEN HEPA FILTER

Captures pollutants and allergens from the air and is equipped with carbon for protection against household odors and VOCs.

SHARK™ AIR PURIFIER 4 ANTI-ALLERGEN HEPA FILTER WITH ADVANCED ODOR LOCK

Captures pollutants and allergens from the air and is equipped with carbon for heightened protection against household odors and VOCs.

SHARK™ AIR PURIFIER 4 ANTI-ALLERGEN HEPA FILTER WITH ADVANCED ODOR LOCK & FUMES LOCK

Captures pollutants and allergens from the air and is equipped with carbon for heightened protection against household odors, VOCs, and fumes such as formaldehyde found in plants, furniture, and flooring.

TROUBLESHOOTING

Customer Service

For further assistance, call 1-855-523-4061.

SharkNinja Operating LLC
US: Needham, MA 02494
CAN: Ville St-Laurent, QC H4S 1A7

1-800-798-7398
sharkclean.com

@sharkcleaning