FuseBox TD1 -Din Rail Mounted 7 Day Time LCD Switch Manual

Technical information

1. Dimensions
   
   Connections (VOLTAGE FREE CONTACTS)
   
2. Time Switch must be installed by a qualified electrician in accordance with the current IET Wiring Regulations BS 7671.
3. Total load must not exceed the rating of the time switch or any additional limitation.
4. For loads greater than above, we recommend an installation contactor is used, switched by the TD1 Time Switch.

BUTTON FUNCTIONS

BUTTON	FUNCTION
ON LED	Illuminates when switching program is on
	Program button
	Clock /Time button
D+	Day
H+	Hour
M+	Minute
RESET	This will DELETE ALL settings!
	By pressing D+ and H+ for 3sec this will also delete all settings!
MANUAL	Manual switch for the following settings: ON, ON AUTO, OFF, AUTO OFF

Initial setup

1. Connect SUPPLY to terminals 1 and 2 and LOAD to terminals 4 and 5.
   Torque connections to 0.8Nm. Loose connections cause fires!!!!
2. Press and hold "RESET" button for 3seconds to initiate programing functions.

Setting the DAY and TIME

Default setting is 24H mode if you wish to change to 12H press "" button for 5 sec, and LCD will display AM. If you want to change back to 24H mode press ""button 5 sec
Step	Key	Setting the DAY
1	Press and hold and press D+ TO CHANGE DAY	The day is displayed at the top of the LCD display
		Setting the TIME
2	Press and hold and press H+ TO CHANGE HOUR	Setting the hour
3	Press and hold and press M+ TO CHANGE MINUTE	Setting the minutes
4	Press	To return to display

Before you start programming the time clock select the function required:
PROGRAMMING, PULSE OR COUNTDOWN (Only 1 of the 3 options can be used simultaneously).

Programming

Step	Key	Programming ON memory locations
1	Press	Setting 1 ON time (display 1 ON)
2	Press H+ or M+	Set hours and minutes
3	Press D+	DEFAULT IS EVERY DAY OF THE WEEK or you can select one of the following options by pressing the D+ button OPTIONS: MO-FR,MO-SA,SA SU,MO-WE,TH-SA,MO WE FR,TU TH SA
Step	Key	Programming OFF memory locations
4	Press	Setting 1 OFF time (display 1 OFF)
5	Press H+ or M+	Set hours and minutes
6	Press D+	DEFAULT IS EVERY DAY OF THE WEEK or you can select one of the following options by pressing the D+ button OPTIONS: MO-FR,MO-SA,SA SU,MO-WE,TH-SA,MO WE FR,TU TH SA
7	Repeat step 2-6	Set 2-16 ON/OFF times
8	Press	End
To review programmed time settings press

FOR THE PROGRAMMED TIMES TO OPERATE AUTOMATICALLY THE TIMER MUST BE SET TO "AUTO OFF"
(ON LED is NOT ILLUMINATED)
IF YOU ARE WITHIN THE SWITCHING TIMES YOU SHOULD SET THE TIMER TO "AUTO ON"
(ON LED is ILLUMINATED)
MANUAL OVERRIDE
Press "MANUAL" to turn ON, ON AUTO, OFF, AUTO OFF programmed times

Pulse

("P" displayed at left hand side of LCD)

Step	Key	Programming ON memory location
1	Press and HOLD H+ and M+	Enter pulse setting ("P" will display LHS)
2	Press and H+ or M+	Set pulse time range: 1sec to 59min 59sec
3	Press and MANUAL	To confirm pulse time range ("P" flashes)
4	Press P	Into setting 1 ON time (display 1 ON)
5	Press H+/M+	Set hours and minutes
6	Press D+	DEFAULT IS EVERY DAY OF THE WEEK or you can select one of the following options by pressing the D+ button OPTIONS: MO-FR,MO-SA,SA SU,MO-WE,TH-SA,MO WE FR,TU TH SA
7	Repeat steps 4-9	Set 2-18 ON PULSE programs (OFF programs not required!)
8	Press	End ("P" will continue to flash when PULSE program is set)
9	Press and HOLD H+ and M+	Exit PULSE function

Countdown

("d" displays in bottom LHC)
This is a manual operation only initiated by pressing the "MANUAL" button on the TD1

Step	Key	Programming COUNTDOWN function
1	Press and HOLD P and	Enter COUNTDOWN setting ("d" displays in bottom LHC)
2	Press and H+ or M+	Set COUNTDOWN time range: 1sec to 99min 59sec
3	Press MANUAL	Start COUNTDOWN
4	Press P	Return to start of COUNTDOWN
5	Press and HOLD P and	End COUNTDOWN ("d" no longer displayed in bottom LHC)

PAUSE program settings

Step	Key	Programming PAUSE function
1	Press and MANUAL for 3s	Permanent "AUTO OFF" state("┌" flashes in bottom LHC)
2	Press and MANUAL for 3s	To restore "AUTO" settings
PAUSE function can only be accessed when "AUTO ON" or "AUTO OFF" is displayed on the LCD

Auto time correction

("7d" displayed at left hand side of LCD)

Step	Key	Programming ON memory location
1	Press P and MANUAL	Into count
2	Press D+	Setting -30s to +30s
3	Press	Confirm

Testing

1. On completion of the installation, it must be tested in accordance with the latest edition of the IET Wiring Regulations for Electrical Installations (BS 7671).

Environment

WASTE ELECTRICAL PRODUCTS SHOULD NOT BE DISPOSED OF IN HOUSEHOLD WASTE. CONTACT YOUR RETAILER OR LOCAL AUTHORITY FOR RECYCLING INFORMATION.

www.fusebox.co.uk