Ecozy IM-BS260A - Ice Maker Manual

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electric shock, ог injury during ice-making operation, always read carefully and obey all safety information.
ALL SAFETY INFORMATION WILL FOLLOW THE SAFETY ALERT SYMBOLS BELOW

SAFETY PRECAUTIONS
You need to follow these instructions and execute.

PROHIBITED MATTERS
Prohibit these operations; otherwise, it will cause danger.

Read and follow these instructions.	Plug the ice maker into а grounded 3 prong outlet with 110~120/60Hz power supply.
Use this ice maker only for its intended purpose as described in this user manual	It is suggested to put the ice maker in a cool and ventilated place, which will greatly improve the ice producing capacity.
Do not use other liquid to make ice cubes other than water.
If the supply cord 5 damaged, it must be replaced by the manufacturer ог its service agent ог а similarly qualified person in order to avoid a hazard.	Unplug the ice maker before cleaning, repairing ог servicing.
	Do not use flammable liquid to clean the ice maker.
Do not turn the ice maker upside down ог tilt it more than 45° during transportation or use. If it happens, let it stand upright for at least one hour before plugging in and using it again.	Place this ice maker away from direct sunlight and make sure that there is at least 6 inches(15 cm) оf free space between all sides of your ice maker and surrounding objects.
Keep flammable materials and vapors, such as gasoline, away from the ice maker.	Do not remove thе ground prong. This ice maker must be properly grounded. Never plug the power cord into а receptacle that is not grounded well and not in accordance with local and national codes.
Do not use an extension cord.
Packaging materials can be dangerous for children. There is а potential risk of suffocation! Keep all the packaging materials away from children.	Children should be supervised to make sure that they do not play with the appliance.
То avoid а hazard due to instability of this ice maker, it must be placed оn an even ог flat surface.	Do not place the power cord over carpets, rugs, etc. Do not cover the cord and do not submerge it in water.

PACKAGE CONTENTS

PRODUCT OVERVIEW

Control Panel

ON/OFF	ON/OFF Button Press this button to start or stop making ice. Press аnd hold this button for 3-5 seconds 10 activate self-cleaning mode.
SELECT	SELECT Button Press this button to select ice cube size: LARGE ог SMALL.
POWER	POWER Indicator Flashes when the ice maker is plugged in; becomes solid оn when the ice maker is making ice.
1СЕ FULL	ICE FULL Indicator Lights up when the ice basket is full.
ADD WATER	ADD WATER Indicator Lights up when there is no enough water in the water tank.
LARGE	LARGE Indicator Lights up when you select LARGE.
SMALL	SMALL Indicator Lights up when you select SMALL,

BEFORE FIRST USE

1. Unpack the ice maker, then remove all the packaging materials.
2. Clean the interior of the ice maker, the ice basket and the ice shovel with warm water and a soft cloth for 3-5 times to remove possible odor or residue ca used by the manufacturing or transportation.
3. Place the ice maker on a level surface in a location where your ice maker is protected from direct sunlight and other sources of heat (such as a stove, furnace, or radiator),
4. Make sure to leave at least 4 inches(10 cm) clearance on all sides of the ice maker for proper air circulation.
   
5. Before plugging in, please let the ice maker stand upright for 1 hour to allow the refrigerant to settle.
6. Plug the ice maker into a well-grounded outlet.
   
   
   Improper use of the plug may result in the risk of electrical shock.

USE YOUR ICE MAKER

Add Water

Open the transparent cover, remove the ice basket, then fill the water tank with clean drinking water. Make sure that the water level is below the MAX line. After adding water, please place the ice basket back and close the cover.

Notes:

• The ADD WATER indicator lights ир when there is по enough water in the water tank
• Please use clean drinking water. Do not use distilled water, beverages including sparkling water or coke.

Start/Stop Making Ice

Press to start making ice; the POWER indicator becomes solid on. Press it again to stop making ice; the POWER indicator flashes again.

Every single ice-making cycle can produce 9 ice cubes. When the cycle ends, the ice cubes will be automatically collected into the ice basket.

Notes:

• When the ice-making cycle ends, open the top cover and transfer the ice cubes to а freezer in time. If the ice cubes melt and the water flows to the water tank, the ice maker will start making ice again.
• Depending on the ambient and water temperature, the ice-making cycle may last for 6 10 13 minutes. If the ambient temperature is too high, the cycle may take longer.
  

Select Ice Cube Size

Press the SELECT button to select the ice cube size. You get two sizes of ice selectable: SMALL and LARGE. Selecting SMALL means the ice-making cycle takes a relatively shorter time.

Notes: If the ice maker is shut down within 5 minutes, please wait at least 5 minutes to restart the ice maker.

Ice Full Reminder

The ICE FULL indicator will light up when the ice basket is full, and then the ice maker Will stop making ice automatically. Gently remove the ice cubes from the ice basket with the scoop, then restart the ice maker.

Self-cleaning Mode

When the ice make is connecting to power and not making ice, press and hold until the LARGE and SMALL indicators flash, which means the ice maker enters self-cleaning mode. It will automatically start cleaning. The process takes 20 minutes.

Tip: This process can be manually terminated by pressing the button at any time.

Water Drain

After the ice maker finishes the ice-making, you can take out the cap an the water drain plug to drain the water in the tank.

Tips:

• It is better to change water every 24 hours.
• If the ice maker is not in use, please clean it and dry all the parts of it

SPECIFICATIONS

TROUBLESHOOTING