Advertisement
DO NOT use on non magnetic materials.
8
DO NOT use on the same steel work as electric welders are being used.
8
2. INTRODUCTION
Manufactured using high quality components for performance and reliability. Made from heavy-duty die cast magnesium alloy with a variable
speed gearbox for greater accuracy. Fitted with a powerful magnet to ensure unit stays adhered at any angle and a double dovetail groove
to increase the stroke length. Includes safety fixing strap and integrated coolant system to extend the life of cutters and increase the quality
of the cut. Can be used with a 16mm twist drill chuck and M8 to M20 Tapping chucks. Designed for use in fabrication, construction and other
applications when drilling/tapping ferrous metal.
3. SPECIFICATION
Model No ......................................................MAG60110VHD
Magnet .......................................................................17000N
Maximum Annular Cutter Capacity ............................... 60mm
Maximum Cutter Depth ................................................ 50mm
Core drill diameter ........................................................ 60mm
Tapping drill diameter .............................................. M8 - M20
Twist drill diameter ....................................................... 23mm
Motor Power................................................................1880W
No Load Speed .......................................................0-220rpm
Stroke length .............................................................. 220mm
Morse taper .....................................................................MT3
Supply ................................................................110V ~ 50Hz
Electrical plug type ................................................... 3-Pin BS
Consumables (not included)
Pilot Pin .................................................................... MAGC.P
Neat Cutting Oil......................................................... NCO/5L
Soluble Cutting Oil .................................................... SCO/5L
4. ASSEMBLY
WARNING! Disconnect from mains supply before performing adjustments.
‰
4.1.
ATTACH COOLANT BOTTLE (fig.1)
4.1.1.
Slacken the 2 thumbscrews and slide bottle cage over the thumbscrews.
4.1.2.
Tighten thumbscrews.
4.1.3.
Connect coolant pipe to the valve on the lubrication ring (fig.1). The pipe can be
released by pushing in the blue valve.
4.1.4.
Make sure the coolant tap is closed, fill the bottle with appropriate lubricant.
4.1.5.
Screw rotation stop (not shown fig.1) to lubrication ring to limit rotation
of hose.
4.2.
ADJUSTING THE SLIDES (fig.2)
4.3.
WARNING! Disconnect from mains supply before performing any adjustments.
4.3.1.
To adjust the friction on the drill slide mechanism, remove the drill cutter.
4.3.2.
Loosen the 5 slide locknuts and adjust the 2.5mm grub screws until the
required amount of friction on the slides has been achieved.
4.3.3.
Tighten the locknuts and test before using the drill.
4.4.
REPLACING THE FUSE (fig.2)
4.4.1.
Undo the fuse cover and replace fuse with one of same rating.
4.5.
FIT CUTTING BIT
4.5.1.
Wind drill head up to maximum height.
4.5.2.
Wind out the two grub screws (fig.1), insert the cutting bit aligning the flats with the grub screw locations and tighten.
5. OPERATION
5.1.
FIT THE SAFETY STRAP
5.1.1.
Securely fix the safety strap though the handle of the drill and around the steelwork. Adjust the length of the strap so that if the drill
should fall the drill should not be allowed to swing too far and be damaged.
5.2.
POSITION THE DRILL
5.2.1.
Connect to the mains supply. Offer drill to workpiece and line up with the previously marked hole.
WARNING! Make sure there is nothing between the magnet and the workpiece BEFORE turning the magnet on.
‰
5.2.2.
Ensure the drill head is wound back away from the workpiece before turning the magnet on.
5.3.
ATTACH DRILL TO WORKPIECE
5.3.1.
Turn the magnet on (fig.2). Wind the drill head down to the workpiece and align the cutting head pin (not supplied) with hole
centre marking.
NOTE:
In order to ensure sufficient magnetic attraction and thus grip to securely hold the drill in place, the workpiece must be at least 10mm
thick.
5.4.
FILL COOLANT BOTTLE
5.4.1.
Always use the correct cutting oil, refer to Section 3.
5.5.
CUTTING THE HOLE
5.5.1.
Turn on the coolant bottle tap (fig.1).
5.5.2.
Back the cutting head away from the workpiece, turn the drill motor on (fig.2). Check the drill sounds and is operating normally.
5.5.3.
Turn the handle anticlockwise to move the cutting bit towards the workpiece.
5.5.4.
Start feeding slowly, with minimal required force to prevent overloading the drill.
CAUTION! Prepare for the cutter bursting through the workpiece.
© Jack Sealey Limited
Original Language Version
fig.2
MAG60110VHD Issue 1 06/03/20
fig.1
Advertisement
