Summary of Contents for Victory EMSD-120
- Page 1 Tractor Implements Embankment Mower Standard Duty Operator’s Manual EMSD-120, EMSD-140, EMSD-160 IMPORTANT READ THESE INSTRUCTIONS BEFORE INSTALLING AND USING THIS IMPLEMENT...
- Page 2 Important Safety Information ... . Safety at All Times ......Look For The Safety Alert Symbol .
-
Page 3: Important Safety Information
Section 5: Specifications & Capacities ..Section 6: Troubleshooting ....Section 7: Appendix ....Bolt Torque . - Page 4 WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury, and includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe practices. CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.
-
Page 5: Practice Safe Maintenance
Practice safe maintenance Understand procedure before doing work. Use proper tools and equipment. refer to Operator’s Manual for additional information. Work in a clean dry area. Lower the implement to the ground, put tractor in park, turn off engine, and remove key before performing maintenance. -
Page 6: Safety Labels
Read and follow their directions. 1. Keep all safety labels clean and legible. 2. Replace all damaged or missing labels. To order new labels go to your nearest Victory dealer or visit our dealer locator at Victory.com. - Page 7 Safety labels...
- Page 8 This shows the grease position. Introduction Victory welcomes you to the growing family of new product owners. This implement has been designed with care and built by skilled workers using quality materials. Proper assembly, maintenance, and safe operating practices will help you get years of satisfactory use from the machine.
-
Page 9: Serial Number Plate
If customer service or repair parts are required contact a dealer. A dealer has trained personnel, repair parts and equipment needed to service the machine. The parts on your machine have been specially designed and should only be replaced with genuine parts. -
Page 10: Section 2: Operating Instructions
CAUTION Tractor PTO shield and all mower guards must be in place at all times during operation! Section 2: Operating Instructions Transporting NOTE: Always disengage PTO before raising mower to transport position. When raising the mower to transport position, be sure that driveline does not contact tractor or mower. -
Page 11: Section 3: Adjustments
9. At first begin mowing at a slow forward speed and shift up until the desired speed is achieved - maintaining 540 PTO rpm. 10. Mower knives will cut better at a faster blade speed than at reduced throttle. 11. After mowing the first 50 feet, stop and check to see that the mower is adjusted properly. 12. -
Page 12: Section 4: Maintenance And Lubrication
1. Tension on the belt can be adjusted with the belt tension bolt. Turn the bolt until desired tension is achieved. When the belt has the correct tension the gearbox should be adjusted so that the gearbox extension is running straight (parallel) with the flail mower. Loosen bolts at the bottom of the gearbox and move gearbox until gearbox extension is running straight. - Page 13 With tension relieved from belt remove old belt from pulleys. Tighten belt tension bolt. Reinstall belt guard and belt guard fender. Storage At the end of the working season or when the mower will not be used for a long period, it is good practice to clean off any dirt or grease that may have accumulated on the mower and any of moving parts.
-
Page 14: Driveline Profiles
Do not overfill! IMPORTANT: Mower should be level when checking oil in gearbox! Driveline Profiles Type of Lubrication: Multi-purpose Grease Section 5: Specifications & Capacities MODEL EMSD-120 EMSD-140 EMSD-160 Dimension(L x W x H) 55’’x57’’x30’’ 63’’x57’’x30’’ 70’’x57’’x30’’... -
Page 15: Section 6: Troubleshooting
Section 6: Troubleshooting Problem Solution CAUTION Do not try to clean rear discharge area when mower is running. Bodily harm may occur! Unplug and clean mower deck. Belt slipping Remove belt guard shields and clean sheaves. Replace belt. Mow at full throttle (540 PTO rpm), check PTO speed and tractor engine. Shift transmission to a lower gear. - Page 16 ENGLISH TORQUE SPECIFICATIONS Bolt Torque Bolt Diameter SAE 2 SAE 5 SAE 8 lb-ft lb-ft lb-ft 1/4” 5/16” 3/8” 7/16” 1/2” 9/16” 5/8” 3/4” 7/8” METRIC TORQUE SPECIFICATIONS Bolt Torque Bolt Diameter 10.9 lb-ft lb-ft 1050 1495 1103 2100 1550 2600 1917 3675...
- Page 17 Victory reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship.
-
Page 18: Section 8: Parts Illustration
Section 8: Parts illustration EMSD Flail Mower Assembly... - Page 21 EMSD Ditch Flail Mower Parts List PART NUMBER DESCRIPTION AGL125.011 Hanging weldment AGF140.108 Cover (B) 1G135.00.107 Bent pin AGF140.011 Supporting frame (S) GB/T1152-89 Oil cup SF-2 Bushing 30X34X40 AGL125.105 Pin（L） AGL125.019 Front swinging arm GB/T96-85 Plain washer 12 EFGC125.110 R pin GB/T889.1-86 Nut M24 AGL125.018...
- Page 22 GB/T93-87 Spring washer 8 GB/T5783-86 Bolt M8X16 GB/T1152-89 Oil cup AGL125.016 Side sway cylinder SF-2 Bushing 65X70X40 SL204.01.103 AGL125.021 The push plate GB/T5783-86 Bolt M24X90 GB/T5783-86 Bolt M12X35 AGL125.106 Belt pulley Cover GB/T5782-86 Bolt M12X110 EFGC125.012 Belt cover GB/T1154-97 Strap SPB1393 JB/T7934Z3 Swellable sleeve EFGC125.117...
- Page 23 EMSD FLAIL MOWER HYDRAULIC SYSTEM EMSD FLAIL MOWER HYDRAULIC SYSTEM Parts List PART NUMBER DESCRIPTION JB/T1002-19 Bolt AGL125.109 Bolt M14 AGL125.026 Oil pipe GB/T3452.1-92 O-ring SBE180.405 Adaptor M16-1/2 GB/T 8606-88 Quick connector R1/2" AGL125.105 Oil pipe...
Need help?
Do you have a question about the EMSD-120 and is the answer not in the manual?
Questions and answers