1. Manuals
  2. Brands
  3. Savi Manuals
  4. Computer Hardware
  5. DSP.One
  6. Dealer manual

Savi DSP.One Dealer Manual

Digital signal processor
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
DEALER GUIDE
DSP.ONE
www.hellosavi.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DSP.One and is the answer not in the manual?

Questions and answers

Summary of Contents for Savi DSP.One

  • Page 1 DEALER GUIDE DSP.ONE www.hellosavi.com...

  • Page 2: Table Of Contents

    12.1. Creating A Scene ............................24 12.2. Playing A Scene ............................. 24 13. Factory Reset ................................ 25 14. Creator ................................... 26 14.1. Connections ..............................27 14.1.1. SAVI Link & Inputs ..........................27 14.1.2. Zones ..............................28 14.1.3. Mixes & Outputs ............................. 29 Page 1 hellosavi.com ©...

  • Page 3: General Description

    GENERAL DESCRIPTION The SAVI DSP.One is a Digital Signal Processor that requires no licensing or additional software. Features a physical 16 x 16 I/O and SAVI Link, a standards-based audio over IP system, for a possible 16 x 32 configuration. 1.1.

  • Page 4: Getting Started

    SAVI’s DSP.One is fully integrated into the overall SAVI architecture but is extremely capable in a configuration without a SAVI Server Pro. As such, the only hardware needed for this setup is the DSP.One, speakers, and one or more sources.

  • Page 5: Physical Layout

    DSP.ONE USER GUIDE 2.2. PHYSICAL LAYOUT A. LED Screen B. D-Pad A. Main Power Input and Switch E. 2 x USB 2.1 Type A B. 4 x Microphone/Line Input (Euroblock, 3.55mm) F. Factory Reset C. 12 x Line Input (Euroblock, 3.55mm) G.

  • Page 6: Front Panel & D-Pad

    DSP.ONE USER GUIDE 2.3. FRONT PANEL & D-PAD The front panel LED screen and D-pad allow access to some basic functionality for the device. Select OK on the D-pad to open the Main Menu. Use the Up and Down arrows to navigate, the Left button to go back, and the OK button to select.

  • Page 7: Connector Wiring

    The entirety of the DSP.One UI is accessible through any modern browser by navigating to the correct IP address and entering a valid Username and Password. The DSP.One Address is set to DHCP by default but may be assigned a static IP address once you login.

  • Page 8: Interface

    DSP.ONE USER GUIDE INTERFACE The DSP.One interface is divided into three main areas: 1. Scene Toolbar: (on the top) This contains all saved Scenes, the New Scene icon, and the Undo button. 2. Configuration Zone: (in the middle) This is where all Config Cards appear when selecting an I/O Card from the Carousel.

  • Page 9: The Carousel And Type Selector

    DSP.ONE USER GUIDE THE CAROUSEL AND TYPE SELECTOR The Carousel is the starting point for any project. Start on the left side of the Type Selector and work your way through the audio flow. Or Start at the end and work your way back.

  • Page 10: I/O Cards

    DSP.ONE USER GUIDE 4.1. I/O CARDS Each of the I/O Cards have an ellipsis menu located in the top right of the card. This menu will always include the current name of the card and a rename option. Additional properties may be available depending on the type of I/O Card.

  • Page 11: Main Menu

    • Logout: Locks the UI and requires entering a username and password to access again. • Update Firmware: Allows uploading a firmware update file. • About: Displays firmware version and SAVI Copyright information. Page 10 hellosavi.com © 2023 SAVI Controls...

  • Page 12: System Settings

    DSP.ONE USER GUIDE 5.1. SYSTEM SETTINGS Select System Settings from the main menu to open. This modal provides configuration fields for the device name and multicast stream settings. Log level settings and the debug port toggle are also available here.

  • Page 13: Network Settings

    When disabling DHCP or making adjustments to the IP address, the device will reboot to complete setup. Please allow up to 30 seconds for the DSP.One to come back online. The new IP address will be displayed on the front panel of the device after the startup process is complete.

  • Page 14: System Logs

    DSP.ONE USER GUIDE 5.3. SYSTEM LOGS Open the menu and select System Logs. This modal displays logs configured in the System Settings. The drop-down menu allows selecting logs for different sections of the device. The refresh icon to the right of the drop-down updates the log output to include the current status.

  • Page 15: Savi Link

    DSP.ONE USER GUIDE SAVI LINK SAVI Link inputs are where you connect audio sources that are already broadcast on the SAVI Canvas network. These include STREAM.One and DSP.One devices. SAVI Link Properties: 1. Mode: This specifies the input connection type.
  • Page 16 Ducking Level: Sets how much other audio input gains are reduced when the paging mic is detected. (100%=gain not reduced, 0%=gain muted) Reminder: Only 16 total Inputs can be active across both SAVI Link and Inputs (Line In) Page 15 hellosavi.com...

  • Page 17: Adding A New Link Input

    DSP.ONE USER GUIDE 6.1. ADDING A NEW LINK INPUT 1. Start by clicking the Add New SAVI Link Input icon in the Carousel to launch the modal. 2. The modal will search the network for broadcasting SAVI Link streams and display them here.

  • Page 18: Inputs

    (range=0 to disable, up to 7,200ms or 7.2 sec). Please see section 10 for EQ settings WARNING: DO NOT CONNECT AMPLIFIED AUDIO TO THE INPUTS OF THE DSP.ONE Reminder: Ensure your cabling is configured correctly for either Balanced or Unbalanced.

  • Page 19: Configuring An Input

    Ducking Level: Sets how much other audio input gains are reduced when the paging mic is detected. (0%=gain not reduced, 100%=gain muted) Reminder: Only 16 total Inputs can be active across both SAVI Link and Line in 7.1. CONFIGURING AN INPUT 1.

  • Page 20: Mixes

    Add New Mix button in the Carousel. Mix Properties: 1. Status: Displays the gain level of all connected SAVI Links and Inputs. 2. Expand/Collapse: The arrow on the side of the card opens to reveal the settings pane.

  • Page 21: Zones

    Zones allow channeling a single SAVI Link, Input, or Mix to multiple Outputs. Zones will appear in Facility View as an Audio Zone. In the DSP.One UI, Zones function like a reverse of Mixes. However, Zones have much more control than Mixes. Zone Properties: 1.

  • Page 22: Outputs

    10. OUTPUTS Outputs are separated into two subcategories; Physical and Network. Physical Outputs offer a host of configuration options while Network Outputs simply make SAVI Links, Inputs, and Zones available to other DSP.Ones on the network. 10.1. PHYSICAL Physical Outputs are where your physically connected speakers are located.

  • Page 23: Network

    Network Outputs are digital only and are also labeled as Virtual Outs. They are used to make SAVI Links, Inputs, and Zones available as a SAVI Link source to other DSP.Ones on the network. These outputs will appear on all DSP.Ones as a discoverable stream.

  • Page 24: Eq Settings

    DSP.ONE USER GUIDE EQ SETTINGS Click on the button to the right of the name under Equalizer to launch the EQ Settings modal. Custom presets can be created, edited, or deleted here. With no restrictions on the number of presets created, the Search bar cuts down on having to scroll through all presets.

  • Page 25: Scenes

    12. SCENES Scenes are how to save your work and are an integral part of the versatility of SAVI’s DSP.One. Creating a Scene saves all current configurations in a quick select shortcut. Once a Scene has been saved, feel free to change settings and rearrange the connections on the DSP.One.

  • Page 26: Factory Reset

    DSP.ONE USER GUIDE 13. FACTORY RESET The device can be completely reset to factory settings with two separate methods. 1. The first method is to navigate to Factory Reset in the Main Menu list, select it, and select OK 2. The second method is to hold in the physical reset button found on the back of the device for 10 sec (see “2.2.

  • Page 27: Creator

    DSP.ONE USER GUIDE 14. CREATOR To fully integrate the DSP.One into an existing SAVI Server Pro project, it will need to be added in Creator. More information on Creator can be found in the Creator Dealer Guide located on the SAVI dealer portal.

  • Page 28: Connections

    The DSP.One requires some minor configuration in Connections. Specifically, source drivers need to be selected for each SAVI Link and Input, and Audio Zones selected for each Zone. Any changes made to this driver will update live on the DSP.One UI (This may require a refresh of the DSP.One UI to reflect the changes).

  • Page 29: Zones

    Similar to SAVI Links and Inputs, Zones require a connected Audio Zone from those available in the project. The properties available for each connection mirror the ones in the DSP.One UI with the addition of an Audio Zone drop-down that pulls from drivers added to the Creator project. There is also a Friendly Name field that may be used to update the name in the DSP.One UI.

  • Page 30: Mixes & Outputs

    14.1.3. MIXES & OUTPUTS Mixes and Outputs may also be configured here. Their properties also mirror those in the DSP.One UI. The Friendly Name field will display any custom name used in the I/O Card for that Mix or Output.

Table of Contents