Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LUXX LIGHTING LUX-200-277-80
Summary of Contents for LUXX LIGHTING LUX-200-277-80
- Page 1 200w LED BAR LUX-200-277-80 USER MANUAL...
-
Page 2: Before You Proceed
Thank you for being a part of the Luxx Lighting family. This manual will guide you through the usage and installation process of the Luxx Lighting 200w LED Bar. Please read and understand this manual in its entirety before using the product. Only use this product as specified within the manual. - Page 3 80R SPECTRUM The 80R spectrum provides a full spectrum with maximum red photon content. The red content is efficiently generated by state of the art LEDs and is the most effective portion of the spectrum for plant growth and yield. The blue-green balance supports healthy plant morphology and enables an improved working environment and improved visual inspection for growers.
-
Page 4: Product Specifications
CONTENTS • 1/4" Hex Head Bolts (2 PCS) • Eyelet Bolts (2 PCS) • Eyelet Bolt Nuts (2 PCS) • Wing Nuts (2 PCS) • Washers (2 PCS) • Unistrut Wire Hangers (2 PCS) • Instruction Manual PRODUCT SPECIFICATIONS Technical Specs Input Voltage Input Current Size &... - Page 5 DAISY CHAINING THE 200W LED BAR Voltage Daisy Chain Quantity The chart shows the maximum amount of 200w LED Bars that can be daisy chained together based on the voltage of your electrical system. 208V 220V 240V 277V PPFD FOOTPRINTS Luxx 200w LED Bar 80R Luxx 200w LED Bar 80R Luxx 200w LED Bar 80R...
-
Page 6: Installation
INSTALLATION WARNING! READ THE FOLLOWING INSTRUCTIONS CAREFULLY BEFORE USING OR WORKING WITH THE 200W LED BAR. • The 200w LED Bar contains a glass lens over the LEDs. Please handle with care. • Always gently place the 200w LED Bar on a clean, soft surface to avoid damaging the glass. •... - Page 7 Power RJ14 Twist Lock CONNECTING UP TO 200x 200W LED BARS How to connect the 200w LED Bar to our NX-1 Controller: • Slide the switch on the bottom of the 200w LED Bar to the EXT/OFF position in order to receive a signal from the NX-1 Controller. •...
-
Page 9: Mounting Methods
HOW TO DAISY CHAIN THE 200W LED BAR There are multiple ways to configure our 200w LED Bar and Bar Bracket when daisy chaining them together. MOUNTING METHODS There are four ways to mount the 200w LED Bar system: Wire hangers to Unistrut Direct mounting to Unistrut Rope Ratchets Bar Bracket... - Page 10 WIRE HANGERS TO UNISTRUT 1. Place the wire hangers over your Unistrut. Lift the 200w LED Bar into the Unistrut. 2. Put the ends of the wire hanger into the holes on the bottom of the 200w LED Bar. DIRECT MOUNTING TO UNISTRUT 1.
- Page 11 ROPE RATCHETS 1. Remove the cap on the end of the slot. Screw the eyelet bolt into the hex nut 2. Position each eyelet bolt towards the ends of the 200w LED Bar. Tighten and insert it into the slot. down the eyelet bolt to secure it in place.
- Page 12 BAR BRACKET INSTALLATION TIPS • Determine how many power cords you will need based on how many 200w LED Bars you can daisy chain together. This is determined by the power cable you select that is rated for your electrical systems voltage. • Plan out how you want to daisy chain your 200w LED Bars in your room to determine where the power cables need to go.
- Page 13 MOUNTING THE BAR BRACKET TO UNISTRUT 1. If you're running a 600w or 1000w system, mount the Bar Bracket through the 2. If you're running a 400w or 800w system, the Bar Bracket is mounted to Unistrut on its own without a middle 200w LED Bar. middle 200w LED Bar.
- Page 14 MOUNTING A 400W OR 800W SYSTEM Start by inserting the 1/4" x 3.5" hex bolt 2. Make sure the hex bolt is seated between 3. Insert the Unistrut cleat over the hex bolt. through the bottom of the Bar Bracket. the two small vertical ribs in the Bar Bracket.
- Page 15 MOUNTING A 600W OR 1000W SYSTEM 2. Insert the Unistrut cleat over the hex bolt. 3. Lift the 200w LED Bar, Bar Bracket, hex bolt and 1. Start by inserting the 1/4" x 3.5" hex bolt into the Unistrut cleat up through the slot in the Unistrut. slot of the middle 200w LED Bar.
- Page 16 MOUNTING THE BAR BRACKET WITH LANCE HANGERS • Install 4 eyelets, one on each end of each Bar Bracket. • Clip the carabiners onto the two opposing eyelets on each Bar Bracket. • Allow an additional 8” from the top of Bar Bracket for the height of lance hangers. Install eyelet bolt here Install eyelet bolt here...
-
Page 17: Maintenance
Luxx Lighting shall, at • Regularly check the cable connections to ensure it is undamaged. its discretion, either replace or repair the product using the appropriate new or reconditioned parts. - Page 18 Luxx 200 LED Bar IMPORTANT SAFETY INFORMATION. READ THIS INFORMATION AND FULL USER MANUAL CAREFULLY PRIOR TO INSTALLING THIS PRODUCT. Installation of the horticultural lighting structures described in this manual shall be performed by qualified personnel and are intended for installation subject to approval by the authority having jurisdiction.
- Page 19 Daisy Chaining If daisy-chaining mains power for the Luxx 200W LED Pro, then it is recommended to use a suitable surge protector. Consult an electrician for the appropriate ratings and installation of the surge protectors. Connect the appropriate cord set to the power inlet cord connector of the luminaire. For 208-240Vac the cord set will be provided with a NEMA Type plug.
Need help?
Do you have a question about the LUX-200-277-80 and is the answer not in the manual?
Questions and answers