Subscribe to Our Youtube Channel
Related Manuals for Avsl Qtx smartLIGHT SL-FC3
Summary of Contents for Avsl Qtx smartLIGHT SL-FC3
- Page 1 RGBW PAR CANS Item ref: SL-FC3, SL-36, SL-64, SL-SW, SL-Q8, SL-Q12 User Manual VERSION 1.1...
- Page 2 INTRODUCTION: LED SMARTLIGHT RGBW PAR CANS The QTX SmartLIGHT family of LED Par cans have been designed for a variety of applications, whether you’re a mobile DJ, a band/singer, a bar/nightclub, theater company or production company then this range of PAR cans will cover most requirements.
-
Page 3: Installation
PACKAGE CONTENTS: Please check the contents to ensure that the product has been received in good condition. SmartLIGHT Box: SmartLIGHT Unit x 1pcs User’s Guide x 1pcs Power Cord x 2pcs (EU and UK) Mounting brackets x 2pcs Controller Box: SL-FC3 Controller x 1pcs 5m cable x 1pcs User’s Guide x 1pcs... - Page 4 CAUTION! : TO PREVENT RISK OF ELECTRIC SHOCK AND ENSURE CORRECT USAGE For your safety, please kindly pay attention to all of the warnings listed below: Always plug in the power plug last and disconnect from the mains, when the ...
-
Page 5: Quick Troubleshooting
CONNECT WITH POWER SUPPLY – THE GROUND WIRE MUST BE CONNECTED: Use the IEC plug to connect to the main power supply as follows: Wire Connection International signal Brown Live Blue Neutral Yellow /Cyan Earth QUICK TROUBLE SHOOTING If the unit is not functioning properly follow the below guidelines Check the IEC cable is fitted correctly. -
Page 6: General Maintenance
GENERAL MAINTENANCE To maintain optimum performance and minimise wear, fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at least twice a month. Dust build-up reduces light output performance and can cause overheating. This can lead to reduced life and increased mechanical wear. - Page 7 FRONT LAYOUT GENERAL: LED Output Secondary bracket Mounting point for G-Clamp Secondary mounting points for more clearance Thumb screw to hold brackets in place Primary bracket SmartLIGHT User Manual Page 7...
- Page 8 REAR LAYOUT SL-36: LED Display Sound sensitivity IEC Power IN (Fuse F1A) Microphone DMX IN DMX OUT Connection to SL-FC3 Foot controller (sold separately) SmartLIGHT User Manual Page 8...
- Page 9 REAR LAYOUT SL-64, SL-SW and SL-Q12: REAR LAYOUT SL-Q8 DMX IN DMX OUT Sound sensitivity Microphone Connection to SL-FC3 Foot controller (sold separately) IEC Power OUT IEC Power IN (Fuse F1A and F3A for SL-Q12) SmartLIGHT User Manual Page 9...
-
Page 10: Control Display
CONTROL DISPLAY: MODE\ESC: Menu or withdraw the last menu UP: Increase one step each time DOWN: Decrease one step each time ENTER: Confirms the functions you select *Note the display will turn off if no activity for 20 seconds. PRIMARY FUNCTION: LED Display Action Sund... -
Page 11: Secondary Function
SECONDARY FUNCTION: A001-A512 DMX-512 Address from 1 to 512 Er_L If there is a breakdown in the DMX connection AUT1 Auto color switch Auto color switch , fade in & fade out effect AUT2 (slow fade in – slow fade out) WRGB Color Scroll, fade in &... - Page 12 The fixture is equipped with 3-pin XLR connectors for DMX input and output. The SE connectors are wired in parallel. Only use a shielded twisted-pair cable designed for 3-pin XLR- plugs and connectors in order to connect the controller with the fixture or one fixture with another.
- Page 13 DMX OPERATIONS: Function Channel Value 000-255 Red Colour 0-100% Dimming 000-255 Green Colour 0-100% Dimming 000-255 Blue Colour 0-100% Dimming 000-255 White Colour 0-100% Dimming 000-255 Master Dimming 0-100% 000-250 Strobe Slow to Fast 251-255 Sound Activated SmartLIGHT User Manual Page 13...
- Page 14 SL-FC3 FOOT CONTROLLER: A combination of up to 32 SmartLIGHT fixtures can be operated by one SL-FC3 controller. SETUP: First connect the foot controller to the first fixture using the supplied cable as shown below. Connecting more than one fixture to the chain requires 3 pin DMX XLR Leads (available at most retailers).
- Page 15 Once all the fixtures are setup turn the power on and set the DMX address on each model to A001. For users who wish to use the sound to light 4 light chase sequences set the DMX to each of the following: Connecting in 4’s PAR can A001...
- Page 16 LED FOOT CONTROLLER OPERATION: SmartLIGHT User Manual Page 16...
-
Page 17: Technical Specification
TECHNICAL SPECIFICATION: For more information visit www.avsl-qtx.com DISPOSAL: Please disposal of an unserviceable device according to the current statutory requirement SmartLIGHT User Manual Page 17... - Page 18 SmartLIGHT User Manual Page 18...
- Page 19 SmartLIGHT User Manual Page 19...
- Page 20 Errors and omissions excepted. Copyright© 2012. AVSL Group Ltd. SmartLIGHT User Manual Page 20...
Need help?
Do you have a question about the Qtx smartLIGHT SL-FC3 and is the answer not in the manual?
Questions and answers