Advertisement

Quick Links

Easy use Easy read

Warning

To prevent electrical shock or equipment damage, unplug the EC207 unit's
power cord from the power supply prior to installing or wiring the EC207.
After completing any EC207 wiring work, be sure the terminal block's
protective plastic cover is reattached. If this cover is not reattached, an
electrical shock could easily occur.
To prevent an electric shock be sure to disconnect your EC207 unit's power
cord from the power supply before wiring the EC207.
Do not use voltage beyond the EC207 unit's specified range. Doing so may
cause a fire or an electric shock.
The cables connected to the EC207 should be secured by cable clamps to
prevent weight or tension of the cables added to the connectors or terminals.
The EC207 unit's wiring should be checked to confirm that both the operating
voltage and wiring terminal locations are correct. If either the voltage or the
wiring terminal location is incorrect, it can cause a fire or accident.
Do not connect or disconnect Host and EC207 unit communication cables
while the EC207 is turned ON.
Do not replace the EC207 unit's battery yourself. The EC207 uses a lithium
battery for backing up its internal clock data and the battery may explode if it is
replaced incorrectly. When replacement is required, please contact your local
EC207 distributor.
To prevent a EC207 unit malfunction due to excessive noise, isolate all EC207
input/output signal lines from all power wiring or power cables via a separate
wiring duct.
Be sure all cable connectors are securely attached to the EC207 unit. A loose
connection may cause incorrect input or output signals.
Be sure to ground the EC207 unit's FG wire separately from other equipment
FG lines. Also, be sure to use a grounding resistance of 100. or less and a
2
2mm
or thicker wire, or your country's applicable standard. Otherwise, electric
shock or malfunctions may result.
Be sure to use only the designated torque to tighten the EC207 unit's terminal
block screws. If these screws are not tightened firmly, it may cause a
short-circuit, fire or incorrect unit operation.
Be sure that metal particles and wiring debris do not fall inside the EC207 unit.
They can cause a fire, malfunction or incorrect unit operation.
Be sure to read the EC207 unit's manual carefully before performing program
changes, entering forced output, or using the RUN, STOP, or PAUSE
commands while the EC207 is operating. Mistakes made when usingthese
items can cause machine accidents or damage.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EC207 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Shihlin electric EC207

  • Page 1 The cables connected to the EC207 should be secured by cable clamps to  Be sure that metal particles and wiring debris do not fall inside the EC207 unit. prevent weight or tension of the cables added to the connectors or terminals.
  • Page 2 I. Specifications Interface Specifications General Specifications COM1/COM2 (RS-232C / RS422/RS485),COM3(RS-232C), Item EC207-CT-00 EC207-CT-11 Ethernet 1. COM1、COM2 and COM3 port Baud Rate、Data Display color 64K colors Length、Parity and Stop Bit can be set on the HMI. Screen type TFT LCD COM1、COM2 及 COM3 three types of communication Screen size ports that can be used simultaneously.
  • Page 3 General Specifications Input Voltage DC 24V Rated Voltage DC 24V ± 10% Range for Within 10ms Instantaneous Stop Power Consumption 15W(Max) Operating Ambient 0℃ ~ 45℃ Temp. Storage Ambient -20℃ ~ 60℃ Temp. Operating Ambient 10%~85%RH (An Environment without Condensation) Humidity Environmental Non-corrosive Environment;...
  • Page 4 II、 Part Names Front: Bottom: Name Description Name Description Display Displays the Utility and the user creation screen screen. SD card interface For installing SD card Power LED:When power is turned on. Run LED:Screen run. Alarm LED:Communication Error.
  • Page 5 人 機 介 面 R00001 EC207-CT-00 型號 額定值 : DC +24V Class 2/500mA 生產工令 : L10M0001 生產序號 : SLHO000001 地址 : 新竹縣新豐鄉中崙村七鄰二三四號 電話 :(03)599-5111 MADE IN TAIWAN PIN definition of serial communication: PIN NO. COM1 COM2 COM3 (10) (11) (12)
  • Page 6 III、External Dimensions IV、EU200 Series Model Name Indication Description EC200 series 7”Display Screen size Colors TFT LCD 00:Standard Type 11:High-Performance Type  Depending on the type of connection cable used the dimensions shown above will change. The dimensions given here are representative values and are intended for reference only.
  • Page 7 V、Installation Make an installation hole on the control panel the dimensions shown below.(Unit: mm)  Max torque:0.3 Nm (2.65 lb-in).
  • Page 8 電話 :(03)599-5111 MADE IN TAIWAN  o avoid an electric shock, prior to connecting the EC207 unit’s power cord terminals to the power terminal block, confirm that the EC207 unit’s power supply is completely turned OFF, via a breaker, or similar unit.

This manual is also suitable for:

Ec series

Table of Contents