Table of Contents
Advertisement
Quick Links
INSTALLATION, SERVICE AND MAINTENANCE INSTRUCTIONS
ANNEX FOR CE MARKED EQUIPMENT ACCORDING TO THE ATEX DIRECTIVE
2014/34/EU:
VERTICAL AGITATOR CRC Ex
The content of this Annex supplements the information in the instruction manual. The instructions in
this Annex must be taken into account in conjunction with the equipment marked according to Directive
2014/34/EU.
This Annex is complemented by the manuals of the ATEX-
certified components comprising the assembly (e.g. drives, etc).
Original Manual
20.067.30.01EN
(B) 2023/05
Advertisement
Table of Contents
Summary of Contents for INOXPA VERTICAL AGITATOR CRC Ex
- Page 1 ANNEX FOR CE MARKED EQUIPMENT ACCORDING TO THE ATEX DIRECTIVE 2014/34/EU: VERTICAL AGITATOR CRC Ex The content of this Annex supplements the information in the instruction manual. The instructions in this Annex must be taken into account in conjunction with the equipment marked according to Directive 2014/34/EU.
- Page 2 20.067.30.03EN (B) 2023/05 EU Declaration of Conformity INOXPA, S.A.U. Telers, 60 17820 - Banyoles (Girona) Hereby declare under Our sole responsibility that the machine VERTICAL AGITATOR Model From serial number IXXXXXXXXX to IXXXXXXXXX is in compliance with all applicable provisions of the following directive:...
- Page 3 The person authorized to compile the technical documentation is the signer of this document. David Reyero Brunet Technical Office Manager Banyoles, 2023 where X is a numeric character coated gearmotor option...
-
Page 4: Table Of Contents
9.11. Parts list of the sanitary coupling flange ............. ¡Error! Marcador no definido. 9.12. Parts list of the tripod ..........................14 9.13. Part list simple mechanical seal ....................... 14 9.14. Parts list double mechanical seal ......................14 INOXPA S.A.U. 20.067.30.01EN · (B) 2023/05... -
Page 5: Generalities
área. 2.3. WARRANTY Any warranty will be void immediately and lawfully and, in addition, INOXPA shall be compensated for any product liability claims submitted by third parties in the case of non-compliance with any of the indications given... - Page 6 (except for starting up this machine), copied, photocopied, made available or otherwise communicated to third parties without our prior written consent. INOXPA reserves the right to modify this annex to the instruction manual without prior notice. INOXPA S.A.U.
-
Page 7: Safety
The limit values for working conditions in explosive atmospheres must not be exceeded. INOXPA will not be held responsible for any damages that may be caused by the use of the agitator in conditions other than those expressed in the ATEX form. -
Page 8: General Information
The agitator was selected for use in explosive atmospheres at the time of placing the order, according to ATEX form. INOXPA is not liable for any damage that may arise if the information provided by the buyer is incomplete or incorrect (liquid type, viscosity, RPM,... -
Page 9: Installation
Figure 1.1.: ATEX CE marking on the nameplate. Should the marking on the machine not correspond with the order, please contact INOXPA immediately to explain the situation. The temperature class and the maximum surface temperature depend on the temperature of the product to be stirred and the ambient temperature. -
Page 10: Location
Follow the gear motor manufacturer's instructions at all times In addition, overload protections suitable for the gear motor power rating must be installed on the gear motor INOXPA S.A.U. 20.067.30.01EN · (B) 2023/05... -
Page 11: Assembly
The switchgear must comply with all applicable regulations, as stipulated in the electrical safety regulations as well as the directions laid down by the manufacturer of the ATEX gear motor 5.5. ASSEMBLY ATEX agitators are very compact machines and are always supplied together with the drive. INOXPA S.A.U. 20.067.30.01EN · (B) 2023/05... -
Page 12: Start-Up
The agitator cannot operate with no fluid in the tank. Therefore, a safety system is required to ensure a minimum fluid level of 350 mm above the top blade when the agitator is running. INOXPA S.A.U. 20.067.30.01EN · (B) 2023/05... -
Page 13: Troubleshooting
Troubleshooting 7. Troubleshooting INOXPA S.A.U. 20.067.30.01EN · (B) 2023/05... -
Page 14: Maintenance
ATEX agitator and include the manufacturing number. If the spare parts are not requested in this way, Inoxpa shall not be responsible for the case that the agitator may not operate with parts which are not suitable for the classified zone where is installed. - Page 15 Incorrect assembly or disassembly may cause the agitator to malfunction and lead to high repair costs and a long down-time period, even invalidating the system's protection systems. INOXPA is not responsible for accidents or damages caused by failure to comply with the instruction manual and with this annex. Cleaning Before disassembling the agitator, it must be cleaned both on the outside and on the inside.
-
Page 16: Technical Specifications
9.9. PARTS LIST OF THE HEAD DOBLE MECHANICAL SEAL 9.10. PARTS LIST OF THE COUPLING FLANGE 9.11. PARTS LIST OF THE SANITARY COUPLING FLANGE 9.12. PARTS LIST OF THE TRIPOD 9.13. PART LIST SIMPLE MECHANICAL SEAL 9.14. PARTS LIST DOUBLE MECHANICAL SEAL INOXPA S.A.U. 20.067.30.01EN · (B) 2023/05... - Page 17 How to contact INOXPA S.A.U.: Contact details for all countries are continually updated on our website. Please visit www.inoxpa.com to access the information.
Need help?
Do you have a question about the VERTICAL AGITATOR CRC Ex and is the answer not in the manual?
Questions and answers