Advertisement
Quick Links
ZHEJIANG RONGPENG AIR TOOLS CO.,L ТО
WWW.RONGPENG.COM
MADE IN CHINA
� '!,CJ,!:,�!:mf{,1:f
Б
OPERATING INSTRUCTIONS FOR FASTENER DRIVING TOOLS OPERATED ВУ
COMPRESSED AIR
Air Nailer -Coil nailer
Model No.:MCN90
IMPORTANT:
Read all safety rules and operating lnstructions
carefully before first use it. Кеер this Manual for future
reference.
6
Residual risks
Even when the tool is used as prescribed it is not possiЫe to eliminate all residua1 risk factors. The following hazards
may arise in connection with the tool's construction and deslgn:
•
Damage to lungs if an effective dust mask is not worп .
•
to
Damage
hearing if effective hearing protection is not worn .
•
Wear еуе proteclion .
•
He,;11l/1 defects resulting from vibration emission if the роwег tool is being used over longer period ot time or not
adequate!y rтianaged and ргорегlу maintained.
Content
1 Technical data
2.7 Actuatiпg systems
1.1 Fastener
З Compressed air system
1.2 Accessories
4 Preparing the tool for use
1.:1 Oe!.r.ription/Featшes
4.1 Preparing а too! fог first operation
1.4 Location of Parts
4.2 Connection to the Compressed air system
2 Special references
4.3 Fi1Iing the magazine
2 .1 Regu\ations
4.4 Handling the tool
2.2 Noise emission
5. Mainlenance
2.3 infarmation оп mechanical impact (vibration)
6 TrouЫeshooting
2.4 Sc1f�ty of fastener driving tool
7 explode drawing
2. 5 Safety at work
8 Spare par1s lis1
2.6 Triggering devices
-------· - - - ---· ·
RP2016
Advertisement
Summary of Contents for Rongpeng MCN90
- Page 1 5. Mainlenance 2.3 infarmation оп mechanical impact (vibration) 6 TrouЫeshooting 2.4 Sc1f�ty of fastener driving tool 7 explode drawing ZHEJIANG RONGPENG AIR TOOLS CO.,L ТО 2. 5 Safety at work 8 Spare par1s lis1 -------· - - - ---· · WWW.RONGPENG.COM 2.6 Triggering devices...
- Page 2 MCN90 MCN90 safety yoke; 1 Technical data for the maintenance of fastener driving tools, only spare parts specified Ьу the manufacturer or his authorized representative Туре of tool MCN90 Required pressure 90-11 ОРSI(6.3-7.5Ьаг) shall Ье used; о repairs shall Ье carried out only Ьу agents authorized Ьу the manufacturer or Ьу other specialists, having due regard io the...
- Page 3 Air Nailer MCN90 Air Nailer MCN90 muzzle of the tool is pressed against а work piece, These tool are marked with ап inverted triangle( '\7 ) behind the serial Oilers must Ье checked оп а daily basis and if necessary topped up with the recommended grade of oil (see TECHNICAL number and are по! permitted for use without ап...
- Page 4 Adjust screw Valve Case Bumper Adjust nut O-Ring 63*2.65 Sпар relainer O-Ring 9х1 .8 Air №iler MCN90 Note: lf you need spare parts of this model, pls feel free to contact us or the distributor where you bought this tool. Tks!
Need help?
Do you have a question about the MCN90 and is the answer not in the manual?
Questions and answers