Advertisement
2.3
Fitting the front fan guard to the rear fan guard. The front guard has a plastic rim attached to it which enables
it to hook over the top of the rear guard (fig 2-A); snap together at the sides, and screw fix at the bottom (fig 2-B).
On the inside of the front guard at the top you will see 2 small square plastic lugs. Hook these lugs over the rim
of the rear guard and push the front guard on as far as it will go at the bottom.
2.4
Hold the two guards together at either side and gently squeeze until they snap together.
2.5
Now take the small plastic fixing lug (fig2-B) and press it into place over the screw fixing hole at the bottom of
the front guard. Place the securing screw through the plastic lug and tighten it up so that the lug fits snugly
against the back of guard rim.
2.6
Check that the guard has been assembled correctly and that the fan will turn freely.
2.7
Assembling the stand. Slot the two crossbars together ( fig3-21 ) and place on a flat surface. Position the
main column (fig3-24) onto the crossed legs and line up the holes in the lower flange with the holes in the
legs.Secure with the four screws provided (fig3-29).
2.8
Unscrew the height adjustment knob (fig3-20) at the top of the column and remove it. Slide the cross bar
cover (fig3-22) over the top of the column and slide it down until it drops over the legs and hides the fixing
flange. Refix the height adjustment knob; pull the inner chrome tube up (fig3-23) ready to receive the main
fan unit and fully tighten the knob.
2.9
Fitting the fan unit to the stand. Check that the chrome tube on the stand is extended (fig2-23) and that
the height adjustment knob has been tightened (fig2-20). On the underside of the fan body (below the
button area) there is a hole (fig2-D) into which the chrome tube will fit. Hold the whole fan unit in an upright
position and drop it onto the top of the chrome tube. Tighten the retaining knob (fig2-C) on the back of the
main body. The fan is now ready to use.
3. OPERATION
WARNING! Ensure you read, understand and apply the safety instructions in part 1 before using the fan.
3.1.
Place the fan in the desired location and plug into the mains power supply.
p
3.2.
Press button “1” (fig2-16) for low fan speed operation, button “2” for medium fan output, and button “3” for high fan output.
To stop the fan press button “0”.
3.3.
To make the fan oscillate, push down the oscillating knob (fig2-12) on top of the motor casing.To stop oscillation, pull the knob up.
3.4.
To adjust the angle of the fan up or down, loosen the swivel knob (fig2-32), position the head accordingly and retighten the knob.
3.5.
To adjust the height of the fan you must first support the main body of the fan with one hand and then loosen the height adjustment
knob (fig2-20) at the top of the main column. Slide the chrome tube up or down as desired and retighten the knob.
3.6.
To swivel the fan unit from side to side loosen the swivel knob (fig2-C) which is at the back of the main body behind and below the
buttons. Swivel the entire fan unit to point in the direction desired and retighten the knob.
4. PARTS LIST
ITEM
PART NO
DESCRIPTION
1
SFP16H01
GRILLE COVER
2
SFP16H02
FRONT GRILLE
3
SFP16H03
SPACER
4
SFP16H04
BLADE LOCK NUT
5
SFP16H05
PLASTIC RING
6
SFP16H06
BLADE
7
SFP16H07
GRILLE LOCK NUT
8
SFP16H08
REAR GRILLE
9
SFP16H09
MOTOR BRACKET
10
SFP16H10
MOTOR
11
SFP16H11
MOTOR COVER
12
SFP16H12
CLUTCH KNOB
13
SFP12H13
LINK ROD
14
SFP16H14
HINGE
15
SFP16H15
BODY COVER
16
SFP16H16
PIANO SWITCH
17
SFP16H17
BODY
18
SFP16H18
TERMINAL BLOCK
19
CS 2.5M2C BLK POWER CORD
20
SFP16H20
HEIGHT ADJUSTMENT KNOB
21
SFP16H21
CROSS BAR SET
22
SFP16H22
CROSS BAR COVER
23
SFP16H23
INNER PIPE
24
SFP16H24
OUTER PIPE
25
SFP16H25
STAND END PLUG
27
SFP16H27
FIXING LOCK
28
SFP16H28
M4 SELF TAP SCREW
29
SFP16H29
M4 SCREW
30
SFP16H30
ADJUSTMENT SCREW
31
SFP16H31
STOPPER
32
SFP16H32
ADJUSTMENT KNOB
Declaration of Conformity
PEDESTAL FAN Model SFP16H
EN 60335-2-80
89/336/EEC Electromagnetic Compatibility
73/23/EEC Low Voltage Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required
for any claim. INFORMATION: Call us for a copy of our latest catalogue on 01284 757525 and leave your full name and address including your postcode.
We, the sole importer into the UK, declare that the product listed below
The construction file for
Sealey Ltd
Signed by Mark Sweetman
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
this
product
is
held by the Manufacturer and may be inspected on request by contacting Jack
01284 757500
01284 703534
Original Date:-
Issue Date:-
Version No:-
Date Modified:-
is
in conformity with the following EEC standards and directives
For Jack Sealey Ltd.
Sole importer into the UK
22st November 2000
of Sealey
E-mail: sales@sealey.co.uk
SFP16H - (1086) - (1) - 201100
fig 2
fig 3
221100
221100
1
1st Issue
Power Products
Advertisement
