Attention: This product should be used with a minimum distance of 25 cm to your body. Attention: Do not use adapter plugs with the charger. Attention: Do not use extension cords with the charger. Attention: Do not remove or adjust any markings, warning symbols or the label of the charger. PEBLAR 2023...
LED feedback Charger status Yellow Start-up / not commissioned / unavailable Green Ready to use, no EV connected / EV connected, but not authorized Blue Authorized Pulsating blue Charging Blinking red Error detected. See Appendix B for troubleshooting PEBLAR 2023...
Page 5
2. Energy charged current session / total energy charged over lifetime / costs of the charging session / energy tariff 3. Indication for energy tariff displayed 4. Unit of displayed number, kWh, €, or €/kWh 5. Indication whether displayed energy corresponds to current session or total energy over lifetime PEBLAR 2023...
For automatic starting of charging the RFID authorization can be disabled (see section 1.5) The vehicle is being charged; the LED status indicator is pulsating blue. This might take a few seconds. PEBLAR 2023...
Browse to the hostname in your browser and log in to the web interface using the password provided with the charger, located at the back of the supplied manual or quick start guide. In the dashboard, multiple settings can be adjusted or observed. The web interface will explain the definition of these settings. PEBLAR 2023...
Up to 22 kW Rated frequency 50 Hz Dimensions (H x W x D, ex. cable) 387 x 207 x 128 mm Weight (excl. cable) Approx. 2.9 kg Charge cable length 4.5 m, 5 m or 7.5 m PEBLAR 2023...
Page 9
23.7 23.7 802.11b/g/n 2400 19.99 Supported protocols Vehicle communication IEC 61851-1 ISO 15118-2* ISO 15118-20* Back-end communication OCPP 1.6J (including security whitepaper) OCPP 2.0.1* Firmware update Locally via web interface Over-the-air via OCPP Blackout protection / load balancing PEBLAR 2023...
The MCB (characteristic B or C) shall have a current rating in accordance with the local mains supply and required charge current (max 32A). The RCD shall be type A (30 mA) or type B (30mA) depending on local regulations. Attention: Check local installations standards for additional requirements. PEBLAR 2023...
Cable gland reduction insert Grommet for peripherals Grommet for mains cable Cable tie for peripherals/charging cable 4(+3*) SIM card** CT coils** 1 (1-phase) 3 (3-phase) Distribution block for CT coils** BUS termination jumper * Cable variants ** Optional PEBLAR 2023...
Page 12
Required tools Number Definition Size Power drill Drill bit 8 mm Spirit level Cable stripper Cable cutter Wire stripper Wire stripper 2 mm Ethernet crimping tool Torx screwdriver Torx screwdriver Torx screwdriver Adjustable wrench Pencil PEBLAR 2023...
Page 13
Select the hole where the mains cable should enter the charger. When the back hole is selected (indicated with in the figure) follow steps 3-4. When the lower hole is selected (indicated with in the figure) follow steps on page 18. PEBLAR 2023...
Page 14
The front assembly (P4) and the base assembly (P5) can be detached from each other. You can detach the two parts by disconnecting the connector from the front assembly. PEBLAR 2023...
Page 15
Strip the power cables at 10 mm. Go to step 7 on page Step 5: Lower hole – preparation Use the cardboard template (P8) and a spirit level to mark the holes for the mounting screws and mains cable. PEBLAR 2023...
Page 16
(H2) and fasten it with the cable gland (P16) at 10 Nm using the adjustable wrench. Only for a mains cable with a diameter of 9 – 14mm place the reduction insert (P16a) into the cable gland. PEBLAR 2023...
Page 17
The figure below shows the different names of the phase rotations. Phase 1 is indicated with an ‘R’ (rotary), phase 2 with an ‘S’ (secondary) and phase 3 with a ‘T’ (tertiary). PEBLAR 2023...
Page 18
Secure the power cables with cable ties (P19). Attention: Connect the phases, neutral and protective earth with the correct connector in the cover. The correct order is indicated on the cover: PE – L3 – N – L2 – L1 PEBLAR 2023...
Page 19
Attention: Connecting the signal wires of the CT coils incorrectly may cause the charger to exceed the configured charging current. Attention: It is recommended to use a shielded Cat-5 (or higher) cable. The maximum length of this cable is 150 meters. PEBLAR 2023...
Page 20
Strip the signal cable and its wires (2). Connect the signal wires to the push-in connector for dynamic load balancing (1), indicated with CT. The figure displays the connector definition per pin. Secure the cable using a cable tie (P19) PEBLAR 2023...
Page 21
(3). During commissioning, make sure that only one charger in the group is configured as ‘Leader’ all others should be configured as ‘Follower’. * Insert the jumper in the first and last charger in the chain SIM card* PEBLAR 2023...
Page 22
Turn on the mains connection. The LED light on the charger should turn yellow first. When it has started up correctly, the status indicator LED should stay yellow. When the status indicator LED turns red, read Appendix B for troubleshooting the error. PEBLAR 2023...
To gain access to the WLAN network, you can: Fill in the credentials manually, provided by the label on the back of the manual or quick start guide. PEBLAR 2023...
Disconnect the peripherals from the front assembly and cut all cable ties (1). Use the push-in connectors at the DIN rail with a flat screwdriver to disconnect the cable ends of the mains cable (3). PEBLAR 2023...
Ask your municipality or local authorities for respective addresses. Recycling of materials saves raw materials and energy and makes a major contribution to conserving the environment. PEBLAR 2023...
0.5 seconds. Each error bar corresponds with 10 seconds. Electrical fault 1 red blink This error indicates that the installation has been performed incorrectly or when there is a ground fault. Contact the installer to solve this issue. PEBLAR 2023...
Page 27
If no dirt or damage is found on the charging plug, follow the charging procedure in section 1.4 of the user manual again. If the charger still indicates that there is a vehicle connection fault, contact your customer support. PEBLAR 2023...
Long Term Evolution Near-Field Communication OCPP Open Charge Point Protocol Power Line Communication Personal Unblocking Key Residual Current Device RFID Radio-Frequency Identification WLAC White-Label AC Charger WLAN Wireless Local Area Network Unit Description Ampere Hertz meter millimeter kiloWatt kiloWatt-hour Volt PEBLAR 2023...
Let op: Gebruik de lader niet in combinatie met laadkabeladapters. Let op: Gebruik de lader niet in combinatie met verlengsnoeren, kabels of haspels. Let op: Zorg dat u markeringen, waarschuwingssymbolen of het label op de lader niet verwijdert of verandert. PEBLAR 2023...
Aan het opstarten / niet in gebruik genomen / niet beschikbaar Groen Klaar voor gebruik, geen EV aangesloten / EV aangesloten, maar niet geautoriseerd Blauw Geautoriseerd Blauw pulserend Aan het opladen Rood knipperend Fout gedetecteerd. Lees Bijlage B om het probleem op te lossen PEBLAR 2023...
Page 33
/ energietarief 3. Indicatie dat energietarief wordt getoond 4. Eenheid van het weergegeven getal: kWh, € of €/kWh 5. Indicatie of de geladen energie van de huidige sessie of van het totaal over levensduur van de lader is PEBLAR 2023...
Voor automatisch starten van het laden kan RFID autorisatie ook worden uitgeschakeld (zie sectie 1.5) Het voertuig wordt opgeladen; de LED- statusindicator is pulserend blauw. Dit kan een paar seconden duren. PEBLAR 2023...
In de webinterface wordt er uitleg gegeven over de definitie van verschillende instellingen. Installatiehandleiding Voorwoord Deze handleiding bevat de installatieprocedure voor installateurs. Het is belangrijk dat u de veiligheidsinstructies leest voordat u begint. PEBLAR 2023...
4,5 m, 5 m of 7,5 m Gebruikersinterface Meerkleurige LED, buzzer, display Ventilatie (IEC 61851 status D) Niet ondersteund Beoogd gebruik Particuliere, commerciële en lichte industriële doeleinden Veiligheid Lekstroomprotectie 6 mA DC aardlekbeveiliging Veiligheidsklasse Klasse I Overspanningscategorie Categorie III PEBLAR 2023...
Page 37
Over-the-air via OCPP Bescherming tegen stroomuitval / load balancing Statisch Instelbare stroomlimiet Dynamische load balancing Bedraad via CT spoelen P1 Dongle Load balancing binnen groepen RS-485 (leider of volger) Installatie Installatielocatie Binnen- en buitengebruik Netaansluiting Alleen permanente netaansluiting PEBLAR 2023...
(karakteristiek B of C) dient te worden gekozen aan de hand van de lokale netstroom en de benodigde laadspanning (max 32A). De RCD dient van type A (30mA) of type B (30mA) te zijn, afhankelijk van lokale regelgeving. Let op: Controleer de plaatselijke installatievereisten om te bepalen of er extra maatregelen nodig zijn. PEBLAR 2023...
Moer voor kabelwartel Kabelwartel P16a Reductie insert voor kabelwartel Doorvoertule voor randapparatuur Doorvoertule voor netstroomkabel Kabelbinders voor randapparatuur/laadkabel 4(+3*) Simkaart** CT spoelen** 1 (1-phase) 3 (3-phase) Verdeelblok voor CT spoelen** BUS afsluit jumper * Alleen voor kabel varianten ** Optioneel PEBLAR 2023...
Page 40
Benodigde gereedschappen Nummer Definitie Formaat Boormachine Boor 8 mm Waterpas Kabel stripper Kniptang Striptang Striptang 2 mm Krimptang voor ethernet Torxschroevendraaier Torxschroevendraaier Torxschroevendraaier Verstelbare sleutel Potlood PEBLAR 2023...
Page 41
Kies de opening waar de netstroomkabel de lader moet binnenkomen. Als u de achterste opening kiest (op de afbeelding aangegeven met H1) volgt u stap 3 4. Als u de onderste opening kiest (op de afbeelding aangegeven met H2) volgt u stap 5 PEBLAR 2023...
Page 42
Let op: Zorg dat de kabels minstens 200 mm zijn om ze later op de gewenste lengte te kunnen snijden. Het voorpaneel (P4) en de base (P5) kunnen van elkaar losgenomen worden. Koppel hiervoor eerst de connector van het voorpaneel. PEBLAR 2023...
Page 43
Strip de stroomkabels op 10 mm. Let op: Zorg dat de stroomkabels rechts van de uitsparing (2) lopen. Ga naar stap 7. Stap 5: Onderste opening – voorbereiding Gebruik de ladersjabloon (P8) en een waterpas om de gaten voor de montageschroeven te markeren. PEBLAR 2023...
Page 44
Step 6: Onderste opening – de base ophangen Het voorpaneel (P4) en de base (P5) kunnen van elkaar losgenomen worden. Koppel hiervoor eerst de connector van het voorpaneel. PEBLAR 2023...
Page 45
Let op: Zorg dat de stroomkabels rechts van de uitsparing (2) lopen. Stap 7: Netwerkaansluiting Wanneer meerdere laders worden aangesloten op één hoofdaansluiting: zie ook 7a Wanneer de lader wordt geinstalleerd op een IT netwerk (drie fasen zonder neutraal): zie PEBLAR 2023...
Page 46
L3 aan laderzijde blijft vrij. Let op: Gebruik deze aansluiting alleen na controle dat de spanning tussen de fasen 230V betreft. Indien deze aansluiting wordt gebruikt bij een ander netwerk zal dit de lader permanent beschadigen. PEBLAR 2023...
Page 47
Zeker de kabels met de kabelbinders (P19). Let op: Sluit de fases, nul en aarde aan op de juiste connector in het voorpaneel. De juiste volgorde staat aangegeven op de kap: PE – L3 – N – L2 – L1 PEBLAR 2023...
Page 48
Let op: Als u de signaaldraden van de CT-spoelen verkeerd aansluit, kan de lader de ingestelde laadstroom overschrijden. Let op: Het is aangeraden om een afgeschermde Cat-5 (of hoger) kabel te gebruiken. De maximale lengte van deze kabel is 150 meter. PEBLAR 2023...
Page 49
Strip de signaalkabel en de draden ervan (2). Sluit de signaaldraden aan op de drukconnector voor dynamische load balancing (1), die is aangegeven met CT. In onderstaande afbeelding ziet u de connectordefinitie per pin. Maak de kabel vast met kabelbinders (P19). PEBLAR 2023...
Page 50
(3). Zorg dat tijdens ingebruiknameprocedure van de laders, er één lader wordt geconfigureerd als ‘Leader’. Alle andere laders in de groep dienen te worden geconfigureerd als ‘Follower’. PEBLAR 2023...
Page 51
Let op: Zorg dat er geen kabels vastzitten tussen de base en voorpaneel. Sluit de connector voor de stroomkabels aan op het voorpaneel totdat u een harde klik hoort. Maak de voorkant dicht. Breng de zes schroeven (P3) aan in de volgorde zoals aangegeven op de afbeelding (2Nm). PEBLAR 2023...
De code die nodig is om het systeem te herstellen wanneer het wachtwoord PUK Code voor de webinterface kwijt is. Deze code is uniek voor elk systeem en kan niet worden gewijzigd. Daarom moet de eigenaar van het systeem deze veilig bewaren. PEBLAR 2023...
Maak de lader los van de netstroomkabel: Koppel de randapparatuur los van het voorpaneel (2). Knip de kabelbinders door (1). Gebruik de drukconnectoren op het aansluitblok op de DIN-rail en een platte schroevendraaier om de kabeluiteinden van de netstroomkabel los te maken. PEBLAR 2023...
Informeer bij de gemeente of bij de plaatselijke autoriteiten naar de betreffende adressen. Het recyclen van materialen bespaart grondstoffen en energie en levert een grote bijdrage aan de bescherming van het milieu. PEBLAR 2023...
Appendix A: Modelidentificatie De modelidentificatie wordt gebruikt om productconfiguraties te kunnen bepalen. Deze tekenreeks bevindt zich op het label op de zijkant van de lader. Met deze tekenreeks kunt u bepalen welke configuratieopties de lader heeft. PEBLAR 2023...
Als u geen vuil of schade aantreft op de laadconnector, volg dan nog een keer de laadprocedure in hoofdstuk 1.4 van de gebruiksaanwijzing. Als de lader nog steeds aangeeft dat er een fout in de voertuigaansluiting is, neem dan contact op met de klantenservice. PEBLAR 2023...
Light Emitting Diode Long Term Evolution Near-Field Communication OCPP Open Charge Point Protocol Personal Unblocking Key Residual Current Device (aardlekschakelaar) RFID Radio-Frequency Identification WLAN Wireless Local Area Network Unit Description Ampere Hertz meter millimeter kiloWatt kiloWatt-hour Volt PEBLAR 2023...
Page 59
Het onderstaande label bevat de benodigde informatie om in te loggen bij de web interface. Attention: Ensure that this label is kept secure as it provides access to the charging system. Let op: Zorg dat dit label veilig wordt bewaard; het geeft toegang tot het laadsysteem. Label location Label location Qr-code Qr-code PEBLAR 2023...