Summary of Contents for Lite the Nite LiteMountA LiteTouch
- Page 1 LiteTouch and LiteTouch PRO Wall Mount 55-110" 139-278cm [275Ibs] Landscape VESA Max 800*600 Portrait VESA Max.400*600 LiteMountA 2016 LiteThe Nite Technologies, LLC All Rights Reserved...
-
Page 2: Installation Overview
Thank you for choosing the Lite Touch and Lite Touch Pro wall mount for your display panel installation. The mount can be configured in landscape or portrait orientation. To install your panel in landscape orientation,complete steps 1 thru 8 of this manual. To install your panel in portrait orientation, complete steps 10 thru 15. - Page 3 Right wall Mount Bracket Panel Bracket Left Wall Mount Bracket Center Wall Mount Bracket 2PCS 1PCS 1PCS 1PCS M5X15 M6X15 M8X15 M10X15 10X70 12X70 4PCS 4PCS 4PCS 4PCS 8PCS 8PCS 4PCS 4PCS 4PCS 12PCS 17mm 14mm 15X8X15 1PCS 1PCS 1PCS 1PCS 1PCS 1PCS...
- Page 4 Assemble The Wall Mount Bracket Attach the center wall mount bracket to the left wall mount bracket and right wall mount bracket using washers (D) and nuts as shown Solid Brick and Concrete Block Landscape Mounting A. Drill a 15/32" hole 2 3/4" deep at each of the mounting locations and insert the plastic anchors (C) B.
- Page 5 Wood Wall Stud Landscape Mounting A. Locate the wood studs in the wall and mark the stud centers. Be sure to attach wall mount to at least 2 studs B. Drill a 3/16" pilot hole at each of the mounting locations in the center of the stud C.
- Page 6 Attach The Panel Brackets To The Display Panel Incorrect Correct Correct A. Install the panel brackets to the rear of the display panel with the “ hook”up as shown below using screws (A) and washers(D). Tighten screws (A) with allen wrench(E) NOTE: Install spacers(G) if your display panel has a recessed back.
- Page 7 Attach The Display To The Wall Mount NOTE: This step should be completed with 2 people due to the weight of the display panel A. Lift the display panel above the wall mount and lower the panel bracket hooks onto the top of the wall mount B.
- Page 8 Adjust Display Panel Tilt Adjust the display panel tilt from -5 degrees to +10 degrees as desired. Grasp the display panel at the top and bottom and move it to the desired angle. Tighten or loosen the Tilt Adjustment Knobs as needed. Tilt Adjustment Knob -5-+10 Congratulations! Your wall mount installation is complete...
- Page 9 How To Remove The Display panel From The Wall Mount Bracket Display Panel Quick Release NOTE: This should be completed with 2 people due to the weight of the display panel A. Pull down on both display panel quick release cables simultaneously while pulling the bottom of the display panel away from the mounting bracket B.
- Page 10 Portrait Installation Below is an example of the assembled wallmount bracket configured for a portrait installation using the left wall mount bracket VESA MAX 400X600 Solid Brick and Concrete Block Portrait Mounting A. Drill a 15/32" hole 2 3/4" deep at each of the mounting locations and insert the plastic anchors(C) B.
- Page 11 Wood Wall Stud Portrait Mounting A. Locate the wood studs in the wall and mark the stud centers. Be sure to attach wall mount to at least 2 studs B. Drill a 3/16" pilot hole at each of the mounting locations in the center of the stud C.
- Page 12 A. Install the panel brackets to the rear of the display panel with the “hook”up as shown Correct Correct Incorrect below using screws(A),washers(D)and allen wrench(E) B. Install spacers (G) if your display panel has a recessed back Be sure the mount is attached as shown Hook...
- Page 13 Attach The Display To The Wall Mount NOTE: This step should be completed with 2 people due to the weight of the display panel A. Lift the display panel above the wall mount and lower the panel bracket hooks onto the top of the wall mount B.