Advertisement
Quick Links
IMPORTANT! PLEASE READ CAREFULLY AND SAVE IT. This user's manual contains important
information about your smoke alarm's operation. To insure your safety, you need install one alarm at least in
your every single room. Please don't open the smoke alarm for that may cause improper effect.
Specifications
Power source: DC9V
Static current: <10uA
Alarm current: 10~20mA
Alarm sonority: >85 db (3m)
Low voltage alarm: 6.5V-7.2V
Working temperature: -10℃~50℃
Where to install smoke alarms
1. At first, you need install them in your bedroom and routeway, and should install one item in every bedroom
at least.
2. Stairway is important for you to rush out when fires occur, so there must install smoke detectors.
3. You at least require one smoke alarm on every floor,including finished attics and basements.
4. Install one alarm beside every electric facility.
5. Install smoke alarms in the middle of ceiling,because smog,heat and flashes always lift to the top of rooms
6. If some reasons cause you can't install them in the middle of ceiling,you need to install them at least 10cm
away from the wall.
7. If you like to install them on the wall, they should be installed 10-30.5cm away under the ceiling. Diagram 1.
CEILING
BEST HERE
ACCEPTABLE HERE
DIAGRAM 1
8. You need install more than one alarm when the length of your hall exceeds 9m.
9. In an ablique roof room,install the alarm 0.9m away from the top.Diagram 2.
10. How to install smoke alarms in a removable house.The removable house is short of heat isolation,so you'd
better install the alarm 10-30.5cm away from the ceiling.for safety you need install another one near your
bedroom,too;
Smoke Alarm
Summary
The smoke alarm adopts photoelectric detector, the flame
and heat are not detected, they are generally more effective
at detecting fast-flaming fires which consume combustible
materials rapidly and spread quickly. Sources of these fires
may be paper burning in a wastebasket, or a grease fire in
the kitchen.
10CM(4'')
MINIMUM
NEVER HERE
SIDE WALL
PD-SO918 instruction
42mm
0.9M(3ft)
0.9M(3ft)
HORIZONTAL DISTANCE
FROM PEAK
DIAGRAM 2
102mm
90mm
ANYWGERE
IN THIS AREA
Advertisement
Related Manuals for pdlux PD-SO918
Summary of Contents for pdlux PD-SO918
- Page 1 Smoke Alarm PD-SO918 instruction Summary The smoke alarm adopts photoelectric detector, the flame and heat are not detected, they are generally more effective at detecting fast-flaming fires which consume combustible materials rapidly and spread quickly. Sources of these fires may be paper burning in a wastebasket, or a grease fire in the kitchen.
- Page 2 Where not to install smoke alarms 1. Where combustion particles are produced. Combustion particles form when something burns. Avoid installing in the areas include poorly ventilated kitchens,garages,and furnace rooms.Keep units at least 6m from the sources of combustion particles(stove,furnace,water heater,space heater)if possible.Ventilate these areas as much as possible.
- Page 3 Test 1. Press and hold the test button on the cover, the smoke alarm should sound. The alarm sound should be loud and pulsating, that indicates the smoke alarm is operating correctly. 2. when it does’nt alarm, the LED flashes once about 40 seconds and while it alarms the LED will flash once a second.
- Page 4 Warning! ● Please confirm with prefessional installation. ● Please cut off power supply before installation and removal operations. ● Make sure that you have cut off the power for safety purposes. ● Improper operation caused losses, the manufacturer does not undertake any responsibility. We are committed to promoting the product quality and reliability, however, all the electronic components have certain probabilities to become ineffective, which will cause some troubles.When designing, we have paid attention to redundant designs and adopted safety...