Advertisement
Quick Links
产品介绍 Introduction
FS-iBC01 是一款采用 i-BUS2 协议适配富斯 AFHDS 3
增强版接收机的电流电压传感器。本传感器可实时回
传电调设备的电压、电流及电池实际消耗容量等信息。
其体积小，易安装，可适配多种模型使用。
概览 Overview
尺寸示意图 /All dimensions are shown as below.
15mm( 高度 /Height)
产品规格 Product Specifications
• 产品型号：FS-iBC01
• 适配设备：支持 i-BUS2 协议系列接收机（如 FTr8B、
FTr12B、INr6-HS 等富斯 AFHDS 3 增强版接收机）
• 适配模型：车、船、飞机等
• 协议类型：i-BUS2
• 输入电源：3.5~9V/DC
• 测量电流：0.5~400A（100~200A 持续小于 15 秒 ,
>200A 持续小于 5 秒）
• 测量电压：0~100V
• 测量容量：0mAh~32767mAh
• 电压测量误差：+/- 0.1V
• 电流测量误差：0.5~100A：<0.5A；
100~200A：<1A；200~400A：<1%
• 在线更新：不支持
• 机身重量：31g( 不含配件负极线 )
42g( 含配件负极线 )
• 温度范围：-20℃ ~ +85℃
• 湿度范围：20% ~ 95%
• 安规认证：CE，FCC
安装与接线 Installation and Cable Connecting
电流电压传感器接线说明
本传感器出厂时，不包含电池接口，选择合适的电池接口后须自行焊接。焊接时，注意接口正负极方向。
Cable connecting instructions for the current and voltage sensor
This sensor is delivered without a battery interface. Therefore, you need to select a suitable battery interface and solder it yourself. Check the
positive and negative terminals carefully when soldering.
Http://www.flysky-cn.com
Copyright ©2023 Flysky Technology Co., Ltd.
FS-iBC01
FS-iBC01, in compliance with i-BUS2 protocol, is a current and voltage sensor
adapted to FlySky AFHDS 3 enhanced version receivers. The sensor can
transfer back the information such as the voltage, current and actual battery
consumption capacity of the ESC in real time. With small size, it is easy to install
and adaptable to a wide range of models.
连接接收机 Newport 接口，如 NPA 接口（须
先在发射机端将此接口协议设置为 i-BUS2） 。
To Newport of Receiver, such as NPA (Set
the protocol of NPA to i-BUS2 through the
transmitter).
[1] - ( 电源负极 )
[2] + ( 电源正极 )
[3] S ( 信号脚 )
[1] - (Power Cathode)
[2] + (Power Anode)
[3] Signal Pin
[4] LED
[5] ESC connector (yellow)
[6] BATT battery connector (red)
• Product Type: FS-iBC01
• Compatible Devices: The receivers with i-BUS2 protocol (such as FTr8B,
FTr12B, INr6-HS and other Flysky AFHDS 3 enhanced version receivers)
• Compatible Models: Cars, boats, airplanes, etc.
• Protocol: i-BUS2
• Input Power: 3.5~9V/DC
• Current Measurement Range: 0.5~400A (100~200A within 15 seconds,
>200A within 5 seconds)
• Voltage Measurement Range: 0~100V
• Measurement Capacity: 0mAh~32767mAh
• Voltage Measurement Error: +/- 0.1V
• Current Measurement Error: 0.5~100A: <0.5A；100~200A: <1A；
200~400A:<1%
• Online Update: None
• Weight: 31g (Excluding accessory negative cable)
42g (Including accessory negative cable)
• Temperature Range: -20℃ ~ + 85℃
• Humidity Range: 20% ~ 95%
• Certifications: CE, FCC
电流电压传感器
Current and Voltage Sensor
[4] LED 灯
[5] ESC 连接端 ( 黄色 )
[6] BATT 电池连接端 ( 红色 )
Advertisement
Summary of Contents for FlySky FS-iBC01
- Page 1 FS-iBC01 电流电压传感器 Current and Voltage Sensor 产品介绍 Introduction FS-iBC01, in compliance with i-BUS2 protocol, is a current and voltage sensor FS-iBC01 是一款采用 i-BUS2 协议适配富斯 AFHDS 3 adapted to FlySky AFHDS 3 enhanced version receivers. The sensor can 增强版接收机的电流电压传感器。本传感器可实时回 transfer back the information such as the voltage, current and actual battery 传电调设备的电压、电流及电池实际消耗容量等信息。...
- Page 2 The cable should be connected as shown in the following digrams, taking XT60 battery as an example( You can select the appropriate interface for your specific battery interface. Make sure that the FS-iBC01 sensor is located on posotive cable(The positive cable is marked in digrams below).
- Page 3 • 请确保本传感器安装在远离磁性物体的地方。 • 不要将本传感器安装在易燃的位置，否则将导致起火。 • 小心电池过度放电。 • 确保电流不超过测量范围，否则将烧坏传感器。 • 禁止将本传感器的 ESC 连接端和电池连接端直接连接电池的正负极，否则将导致起火。 Attentions: • Ensure that the sensor is connected properly to i-BUS2 interface of the receiver before use. • Ensure that the positive and negative connectors of the interface are correctly connected! If connected incorrectly, an explosion or fire may occur. • Make sure that the connectors of all interfaces are connected securely! If the connectors fall out during use, the model may be out of control, resulting in a danger. • Make sure that this sensor is installed away from magnetic objects. • Do not install this sensor in a flammable location. Otherwise, there may be a fire. Battery • Check carefully whether the battery is over-discharged. • Make sure that the current does not exceed the measurement range. Otherwise, the sensor may be damaged. • Never connect the sensor to a battery directly. Otherwise, there may be a fire. Http://www.flysky-cn.com Copyright ©2023 Flysky Technology Co., Ltd.
- Page 4 -- Consult the dealer or an experienced radio/TV technician for help. EU DoC Declaration Hereby, [Flysky Technology Co., Ltd.] declares that the Radio Equipment [FS-iBC01] is in compliance with RED 2014/53/EU. The full text of the EU DoC is available at the following internet www.flyskytech.com/info_detail/10.html.