Table of Contents
Advertisement
Quick Links
FAST Installation (PMRS/TMRS 104/201/410/110)
Date of release: April, 2016
Preface: This manual Consists of 3 main parts:
Chapter one:
Introduction
Chapter two:
Hardware interfaces
Chapter three:
Installation
SIM Data Card
Camera(s)
Micro SD Card
Required Items
4G/3G/HSPA/EDGE
SIM Data Card from a cellular
provider is required for the unit.
Any analogue PAL/NTSC camera
can be connected to the PMRS
unit.
A Micro SD Card is required for
recording in the MRS device. The
speed of the SD Card will vary
depending on the make.
SDs with storage above 32GB have to
be formatted to a FAT32 format
(through third party apps).
Advertisement
Table of Contents
Summary of Contents for INFODRAW TMRS 104
- Page 1 FAST Installation (PMRS/TMRS 104/201/410/110) Date of release: April, 2016 Preface: This manual Consists of 3 main parts: Chapter one: Introduction Chapter two: Hardware interfaces Chapter three: Installation Required Items SIM Data Card 4G/3G/HSPA/EDGE SIM Data Card from a cellular provider is required for the unit.
-
Page 2: Chapter 1 - Introduction
Chapter 1 - Introduction 1-1 Introduction: Infodraw PMRS is a portable handheld multimedia streaming and monitoring system from the field. It allows users to stream live video/audio/location from anywhere over the cellular 4G/ 3G/ HSPA/ EDGE networks and can be monitored from any location upon alarm/ request. The media streaming is done using PMRS units which can be carried handheld or located either on mobile vehicles or fixed locations. -
Page 3: System Architecture
1-3 System Architecture: Server-Based – M2M (recommended). This architecture is based on a server with a fixed IP address. Multiple units can communicate with the server as well as multiple clients. All clients are connected to the server and have viewing and control capabilities. -
Page 4: Chapter 2 - Unit Hardware Interfaces
Chapter 2 - Unit Hardware Interfaces 2-1 Video Input/ Audio Input/ 5V Power Output: The unit has a standard input jack (2.5mm) which supports the video input, audio input and 5V power output to the camera from the unit. 2-2 Video / 5V Power Adapter Cable: The unit has a standard adapter cable which has a RCA Female connector for Video input, a RCA Female connector for Audio input and a 5V DC Power... - Page 5 2-6 SIM Card Slot: The SIM card slot is located on the side of the unit. Pull the notch out to insert the SIM card. 2-7 Alarm Button: The PMRS has a built in alarm button located on the side of the unit. The button can be used in emergencies and can be set up to trigger a variety of actions on the MRS monitor (Refer to Alarm Button Section).
- Page 6 2-11 Dip Switches: The PMRS has 2 Dip Switches located on the side of the unit. The dip switches are for setup and operation. The functions of each switch are described below in order from left to right: 1) USB HOST/CLIENT AND CELLULAR OPERATION: UP - USB client –...
- Page 7 2-13 I/O Cable: The i/o Cable has several different coloured wires for specific purposes such as PTZ and GPIO. The definitions of the wires are listed below. HDMI COLOR FUNCTION BLUE GPIO IN 1 WHITE-BLACK GPIO IN 2 ORANGE 12V ON RED-BLACK EXTERNAL ON GREEN...
-
Page 8: Chapter 3 - Installation
Chapter 3 - Installation PMRS software can be downloaded from http://www.infodraw.com/dlds 3-1 Installation on Server Computers 1. Open ports 12654 (TCP) and 12655 (UDP) on the firewalls of your computer and your router. 2. Make sure the IP of the server is static, external and can be reached from the outside. - Page 9 3-2-1 Set parameters via PC (Device Configurator – 7 and below) 1. Browse to the website: www.infodraw.com/dlds 2. Open the folder of the latest version of the PMRS ("5.4.1.0" for example). 3. Enter the “MRS device config” folder and activate the Setup_MRS_DeviceConfig.msi file.
- Page 10 9. System will restart to "Advanced Boot Options" screen 10. Select "Disable Driver Signature Enforcement" Once the system starts, install the Infodraw drivers as you would on Windows 7 (64-bit OS) – Described in the in the 2 pages preceding this one.
- Page 11 3-2-4 Set Parameters via Android (MRSconfig) Attention! This feature is only available in PMRS 201/104/410 devices MRSConfig Activation: Look for the MRSConfig app in your "google play" store, download it - the application is free. Step 1: Prepare the DIP switches, the left DIP switch needs to be in a "down" position and the right DIP switch needs to be elevated Step 2: Activate the PMRS Device Step 3: Activate the Bluetooth feature on your Android phone and Click on the...
-
Page 12: Watch Video
3-3 Watch video 1. Open your browser to www.infodraw.com/dlds 2. Open the folder of the latest MRS version and in it, open the folder of the Monitor-Client. 3. Run the Setup_MRS_Client.msi file and install the program. 4. After installation is complete, open the MRS Monitor program.