DO NOT use drill in an area where paint fumes, solvents or flammable liquids pose a potential hazard. Keep flammable material away
from the drill when operating. Flammable waste, such as wiping or cleaning rags, must be placed in a closed metal container and
disposed of correctly.
DO NOT exceed the rated capacity of the drill.
DO NOT leave the drill operating unattended.
DO NOT operate the drill when you are tired, under the influence of alcohol, drugs or intoxicating medication.
7
When not in use switch off the drill, remove plug from the power supply and do not leave until the drill has come to a complete stop.
2. INTRODUCTION
A comprehensive range of floor pillar drills for the professional workshop. Models feature heavy-duty aluminium-bodied induction motors for
long and reliable performance. No-volt release switch to prevent inadvertent start up and pulley cover protected by microswitch to prevent
drill operating when cover is open. Selected models are fitted with an integral work light which illuminates the drilling table giving operator a
clear view of the drilling process. All models supplied with an electrically inter-locked flip-up chuck guard. Large sized square tables fitted with
precision rack and pinion height adjustment.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . PDM170F.V2 . . . . . . . . . . PDM210F.V2 . . . . . . . . . . . PDM240F.V2 . . . . . . . . . PDM260F.V2
Drilling Capacity (Chuck Size):. . . . . . . . . 16mm. . . . . . . . . . . . . . . . 16mm . . . . . . . . . . . . . . . . . 20mm . . . . . . . . . . . . . . . . . . . . . 20mm
Spindle Nose Taper: . . . . . . . . . . . . . . . . . MT2 . . . . . . . . . . . . . . . . . MT2 . . . . . . . . . . . . . . . . . . MT3 . . . . . . . . . . . . . . . . . . . . . . . MT4
Spindle Centre to Column: . . . . . . . . . . . . 170mm. . . . . . . . . . . . . . . 190mm . . . . . . . . . . . . . . . . 216mm . . . . . . . . . . . . . . . . . . . 260mm
Spindle Travel: . . . . . . . . . . . . . . . . . . . . . 80mm. . . . . . . . . . . . . . . . 80mm . . . . . . . . . . . . . . . . . 80mm . . . . . . . . . . . . . . . . . . . . 120mm
Number of Speeds: . . . . . . . . . . . . . . . . . 16. . . . . . . . . . . . . . . . . . . 16 . . . . . . . . . . . . . . . . . . . . 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Speed Range: . . . . . . . . . . . . . . . . . . . . . 190-3000rpm . . . . . . . . . . 190-3000rpm . . . . . . . . . . . 160-3000rpm . . . . . . . . . 120-3480mm
Maximum Distance Spindle to Table: . . . . 770mm. . . . . . . . . . . . . . . 725mm . . . . . . . . . . . . . . . . 720mm . . . . . . . . . . . . . . . . . . . 680mm
Maximum Distance Spindle to Base: . . . . 1255mm. . . . . . . . . . . . . . 1225mm . . . . . . . . . . . . . . . 1230mm . . . . . . . . . . . . . . . . . 1160mm
Working Table Surface Size: . . . . . . . . . . 254 x 254mm. . . . . . . . . . 290 x 290mm . . . . . . . . . . . 356 x 356mm . . . . . . . . . 425 x 475mm
Working Base Surface Size: . . . . . . . . . . 205 x 200mm. . . . . . . . . . 205 x 200mm . . . . . . . . . . . 205 x 200mm . . . . . . . . . 410 x 330mm
Overall Base Size: . . . . . . . . . . . . . . . . . . 450 x 270mm. . . . . . . . . . 495 x 290mm . . . . . . . . . . . 495 x 290mm . . . . . . . . . 575 x 455mm
Column Diameter: . . . . . . . . . . . . . . . . . . 73mm. . . . . . . . . . . . . . . . 80mm . . . . . . . . . . . . . . . . . 80mm . . . . . . . . . . . . . . . . . . . . . 92mm
Collar Diameter: . . . . . . . . . . . . . . . . . . . . 55mm. . . . . . . . . . . . . . . . 60mm . . . . . . . . . . . . . . . . . 75mm . . . . . . . . . . . . . . . . . . . . . 85mm
Overall Height: . . . . . . . . . . . . . . . . . . . . . 1610mm. . . . . . . . . . . . . . 1610mm . . . . . . . . . . . . . . . 1635mm . . . . . . . . . . . . . . . . . 1710mm
Motor Power (Start): . . . . . . . . . . . . . . . . . 600w . . . . . . . . . . . . . . . . 600W . . . . . . . . . . . . . . . . . 1000W . . . . . . . . . . . . . . . . . . . 1500W
Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V . . . . . . . . . . . . . . . . 230V. . . . . . . . . . . . . . . . . . 230V . . . . . . . . . . . . . . . . . . . . . . .230V
Noise Pressure: . . . . . . . . . . . . . . . . . . . . 76.9dB . . . . . . . . . . . . . . . 76.9dB . . . . . . . . . . . . . . . . 76.9dB . . . . . . . . . . . . . . . . . . . 76.9dB
Noise Power: . . . . . . . . . . . . . . . . . . . . . . 89.1dB . . . . . . . . . . . . . . . 89.1dB . . . . . . . . . . . . . . . . 89.1dB . . . . . . . . . . . . . . . . . . . 89.1dB
Duty Cycle: . . . . . . . . . . . . . . . . . . . . . . . . S1 . . . . . . . . . . . . . . . . . . S1. . . . . . . . . . . . . . . . . . . . S1 . . . . . . . . . . . . . . . . . . . . . . . . . . .S1
Optional Keyless Chuck 16mm: . . . . . . . . PDM/KC. . . . . . . . . . . . . . PDM/KC . . . . . . . . . . . . . . . PDM/KC . . . . . . . . . . . . . . . . . PDM/KC
Integral Work Light (Bulb not included):. . No . . . . . . . . . . . . . . . . . . Yes . . . . . . . . . . . . . . . . . . . Yes . . . . . . . . . . . . . . . . . . . . . . . . . Yes
4. CONTENTS
4.1. PACKAGE CONTENTS Unpack the parts listed below and check to ensure they are in good condition. Any queries must be reported
to your stockist immediately.
3 Head Assembly
3 Column with Flange
3 Adjusting Handle with Set Screw (table)
3 Pivoted Clamp Bolts (2, except PDM260F-1)
3 Safety Guard
3 Wedge
5. ASSEMBLY
Note: Figures are illustrative and may differ in detail from your drill.
5.1.
ASSEMBLY
5.1.1. Place the column assembly on the base, align holes and secure with the bolts and washers provided.
5.1.2. Install table bracket onto column together with rack (fig.1), engaging gear in bracket with rack.
5.1.3. Install the rack collar and tighten firmly (fig.2).
5.1.4. Install the table adjusting handle (fig.2.A) and pivoted clamp bolt (the longer of the two - fig.2.B).
5.1.5. Tighten the handle set screw (with the hex. key provided) and the bracket clamp bolt.
5.1.6. Install the table and table clamp bolt (fig.3).
5.1.7. Carefully place the head assembly over the column and slide it into position. Align head with base.
5.1.8. Fit the two set screws in the side of the head and tighten with hex. key (fig.4) to lock head in position.
5.1.9. Fit the feed handle to the hub of the pinion shaft (align pin with slot) and retain with central screw.
5.1.10. To install chuck: open the chuck jaws completely by turning the chuck key anticlockwise. Place a piece of wood on the drill table
(to prevent the chuck from getting damaged).
5.1.11. Insert arbor (fig.5.B) into drill spindle (reduced diameter end first), fit chuck to protruding end of arbor and hold in place.
5.1.12. Turn feed handle to bring nose of chuck down onto wood (fig.5). Firmly pull on feed handle to seat arbor tapers in spindle and chuck.
5.1.13. Loosen clamp screw on safety guard mounting collar, pass guard up over chuck and fit collar round flange of quill shaft. Ensure guard
pivot is central and tighten clamp screw.
5.2.
DRILL MOUNTING
5.2.1. For stability and safety it is important that the drill base is securely bolted to the floor.
5.2.2. Ensure that the floor is capable of supporting the drill together with the weight of the heaviest likely workpiece.
NOTE: The belt guard and chuck guard are both protected by microswitches which isolate the machine should either guard be open.
© Jack Sealey Limited
3 Base
3 Feed Handle
3 Table
3 Bolts and Washers (4)
3 Arbor
3 Hex. Keys (2)
Original Language Version
3 Chuck and Key
3 Table Arm, Bracket & Worm (PDM260F - no arm)
3 Rack and Rack Ring
3 Screw (upper pulley cover)
3 Set Screws (2)
fig. 1
PDM170F.V2, 210F.V2, 240F.V2, 260F.V2 Issue:2 (3) 03/03/21