1. Manuals
  2. Brands
  3. Broadcast Tools Manuals
  4. Relays
  5. BOR-4
  6. Installation and operation manual

Broadcast Tools BOR-4 Installation And Operation Manual

Box o'relays 4
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installation and Operation Manual
Firmware version 1.15 and above
Due to the dynamic nature of product design, the information contained in this
document is subject to change without notice. Broadcast Tools, Inc., assumes no
responsibility for errors and/or omissions contained in this document. Revisions
of this information or new editions may be issued to incorporate such changes.
Broadcast Tools® is a registered trademark of Broadcast Tools, Inc.
Copyright, 1989 - 2005 by Broadcast Tools, Inc. All rights reserved.
No part of this document may be reproduced or distributed without permission.
Visit www.broadcasttools.com for important product update information.
BOR-4
Box O'Relays 4
Manual Update: 2/10/2004
®

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BOR-4 and is the answer not in the manual?

Questions and answers

Related Manuals for Broadcast Tools BOR-4

Summary of Contents for Broadcast Tools BOR-4

  • Page 1 Manual Update: 2/10/2004 Due to the dynamic nature of product design, the information contained in this document is subject to change without notice. Broadcast Tools, Inc., assumes no responsibility for errors and/or omissions contained in this document. Revisions of this information or new editions may be issued to incorporate such changes.

  • Page 2: Table Of Contents

    BOR-4 Installation and Operation Manual Table of Contents Section Title Page # Introduction ..........3 Safety Information .

  • Page 3: Introduction

    BOR-4 Installation and Operation Manual INTRODUCTION CAUTION! Thank you for your purchase of a Broadcast Tools® BOR-4, Box O’ Relays Broadcast Tools® (referred to as the BOR-4 throughout this manual). We’re confident that this prod- Products, as with any uct will give you many years of dependable service. This manual is intended to give electronic device, can you all the information needed to install and operate the Broadcast Tools®...

  • Page 4: Product Description

    5-volt TTL/CMOS compatible inputs. Other unique features of the BOR-4 are the Programmable logic and pulse stretching (delays) from 500 ms (1/2 second) to 108 minutes. The BOR-4 is equipped with a single small profile aluminum chas- sis.

  • Page 5: Component Options

    BOR-4 Installation and Operation Manual Component Options: We provide pads for a NO momentary switch (SW2). This optional switch is con- nected to input one of K1. Pads are provided to install an optional sonolert (S1). The sonolert is connected to K1 via the enable jumper JP13.
  • Page 6 BOR-4 Installation and Operation Manual Mode 3: Set/Reset (Flip/Flop) – A low going pulse on input 1 (set) latches the relay. A low going pulse on input 2 (reset) unlatches the relay. Note: The state is stored in non-volatile memory during power failures in mode 3 only.

  • Page 7: Relay 1 Configuration

    BOR-4 Installation and Operation Manual RELAY 1 CONFIGURATION Function TB-1 TB-1 Optically Isolated Pin 1, Cathode Pin 2, Ground 1 & 2 3 & 4 2 & 3 Dry Contacts of Opto-Isolator Optically Isolated Pin 1, Cathode Pin 2, Anode of 2 &...

  • Page 8: Relay 2 Configuration

    BOR-4 Installation and Operation Manual RELAY 2 CONFIGURATION Function TB-2 TB-2 Optically isolated Pin 1, Cathode of Pin 2, Ground 1 & 2 3 & 4 2 & 3 Dry Contacts Opto-Isolator Optically isolated Pin 1, Cathode of Pin 2, Anode of 2 &...

  • Page 9: Relay 3 Configuration

    BOR-4 Installation and Operation Manual RELAY 3 CONFIGURATION Function TB-3 TB-3 Optically isolated Dry Pin 1, Cathode Pin 2, Ground 1 & 2 3 & 4 2 & 3 Contacts of Opto-Isolator Optically isolated Pin 1, Cathode Pin 2, Anode of 2 &...

  • Page 10: Relay 4 Configuration

    BOR-4 Installation and Operation Manual RELAY 4 CONFIGURATION Function TB-4 TB-4 Optically isolated Pin 1, Cathode Pin 2, Ground 1 & 2 3 & 4 2 & 3 Dry Contacts of Opto-Isolator Optically isolated Pin 1, Cathode Pin 2, Anode of 2 &...

  • Page 11: Installation

    EGND terminals. The station ground should be connected to the chassis ground screw located on the far right side of the BOR-4 as viewed from the rear. It is rec- ommended that all cables connected to the BOR-4 be looped through ferrite cores to suppress RF.
  • Page 12 STEP 5: CONNECT YOUR EQUIPMENT Be cautious when con- necting a telephone line The BOR-4 interfaces to your equipment through rear panel screw terminals. to the BOR-4. Only Follow the silk-screened legends on the PCB for the desired connections. Use a...

  • Page 13: Specifications

    BOR-4 Installation and Operation Manual BROADCAST TOOLS ® BOR-4 SPECIFICATIONS Logic: uProcessor w/non-volatile memory Inputs: Momentary or sustained, optically isolated (5 to 28vdc) or 5 volt CMOS/TTL compatible inputs, open collector or contact closures to ground. Ring voltages from 80 to 130 volts.

  • Page 14: Warranty

    If Broadcast Tools is notified, in writing, of a failure of any item manufactured by Broadcast Tools to conform to the foregoing Limited Warranty within one (1) year following the date of the Buyer’s acquisition of the item, and if the item is returned to Broadcast Tools in accordance with Broadcast Tools’...

Table of Contents