Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for VANPOWERS SW-LCD
Summary of Contents for VANPOWERS SW-LCD
- Page 1 Vanpowers Bike Display User Manual For Manidae...
- Page 2 USER GUIDE SW-LCD...
-
Page 3: Table Of Contents
Content 1. Appearance and Specifications ..................4 1.1 Materials ......................4 1.2 Display Measurements ..................4 2. Overview of Functions and Buttons ................5 2.1 Preset and Default Items .................. 5 2.2 Display Example Image ..................5 2.3 Buttons ......................6 3. Installation Instructions ..................... 7 4. -
Page 4: Appearance And Specifications
1. Appearance and Specifications 1.1 Materials The SW-LCD display shell has a sleek black-and-white design and can be used normally at temperatures ranging from –20 ℃ to 60 ℃. 1.2 Display Measurements Units are in millimeters (mm). -
Page 5: Overview Of Functions And Buttons
Overview of Functions and Buttons 2.1 Preset and Default Items The available SW-LCD user settings include wheel diameter (18–28 inches), max speed, backlight level, display units, and more. 2.2 Display Example Image The screen displays battery capacity, assist level, speed, distance traveled, power usage, cruise control mode, and an error code if there is an issue with the electronic control system. -
Page 6: Buttons
2.3 Buttons The SW-LCD is equipped with a button set that can be installed on either side of the handlebar. Its specifications in millimeters are as follows: The button set is connected to the bottom of the SW-LCD display via the... -
Page 7: Installation Instructions
In the following instructions, is represented by [MODE], is represented by [UP], and is represented by [DOWN]. 3. Installation Instructions Affix the display and the button set to the handlebar and adjust the angle for easy viewing while riding. With the e-bike turned off, connect the display cable to the controller cable to finish installation. -
Page 8: Maximum Speed
Wheel diameter interface Press [UP] or [DOWN] to choose the correct diameter (18–28 inches) for your wheels. The default setting is 26 inches. Press [MODE] to save your changes and progress to the maximum speed setting. 4.4 Maximum Speed The second setting is maximum speed. The interface looks like this: Maximum speed interface This is where the maximum riding speed can be set. -
Page 9: Backlight Brightness
15.5 mph (25 km/h). Press [MODE] to save your changes and progress to the backlight brightness setting. Warning: Raising the speed limit of your e-bike may violate your local laws. Vanpowers Bike is not responsible for any issues caused by your decision to change the speed limit. 4.5 Backlight Brightness The third setting is backlight brightness. -
Page 10: Exit Settings
The fourth setting is speed and distance units. The interface looks like this: Unit settings interface Press the [UP] or [DOWN] key to choose between imperial and metric speed units. The distance units will change accordingly. 4.7 Exit Settings While in the settings, long press the [MODE] key for 3 seconds to save your changes and exit. -
Page 11: Battery Capacity
5.2 Battery Capacity When the battery is charged to full or nearly full capacity, all five segments will be lit. When the battery is running low, the last segment will flash at 1 Hz, indicating that the battery needs to be recharged immediately. -
Page 12: Assist/Throttle Level
Speed display interface 5.4 Assist/Throttle Level Press [UP] or [DOWN] to change the output power of the motor. The power ranges from level 1 to level 5, with 1 being the minimum and 5 being the maximum. The default level is 1. Assist level interface 5.5 Odometer Press the [MODE] key to switch between current trip distance (TRIP) and... -
Page 13: Cruise Control
Distance interface 5.6 Cruise Control Long press the [DOWN] key for 3 seconds to enter a power-assisted walk mode. The bike will travel at a fixed speed of 3.7 mph (6 km/h). Power-assisted walk interface Warning: Cruise control mode is only recommended while pushing the bike. -
Page 14: Power Usage
When the backlight is turned on, the headlight will be also turned on if the bike has one. Backlight interface 5.8 Power Usage This displays the e-bike’s real-time power consumption. Power usage interface 6. Warnings Practice safe riding and avoid collision with the display as much as possible. -
Page 15: Q&A
Avoid riding with a low battery to prevent damage to it. The screen will get dark when temperatures fall below –10 ℃ and will brighten again as the temperature rises. 7. Q&A Q：Why can I not turn on the display? A：Please check whether the lead cable is properly connected to the controller cable. -
Page 16: Software Version
Due to the use of waterproof cable connectors, users will not be able to see the colors of internal wires. 10. Software Version This instruction manual was written for a general-purpose version of the display software (V2.0). The software version used in some displays may be slightly different from that described in this manual, and in these cases, the actual version shall take precedent over the manual’s.