Page 1
Electric fencing Instructions for use CONSOLE for solar panels Thank you for purchasing a product from VNT electronics s.r.o. The consoles are used to mount solar panels to boxes or holders. IMPORTANT NOTIFICATIONS • When installing, make sure you comply with all safety regulations.
Electric fencing +420 730 893 828 Instuctions on how to build the console for 40 W solar panel CONTENT 40W panel – console for portable box (Art.No. 8145) (Art.No. 8163) (Art.No. 8150) . . . . . . . .
• 2 pcs M6 wing nut 1.1 Console assembling Assemble the console parts according to the drawing and screw the parts together at the marked points. Use 8 pcs M5 × 14 mm screw, 8 pcs M5 nut and 16 pcs M5 washer.
1.2 Solar panel mounting Screw the consoles according to the drawing with 4 pcs M5 × 14 mm screw, 4 pcs M5 nut and 8 pcs M5 washer to the panel. · 4 pcs M5 × 14 mm screw · 4 pcs M5 nut ·...
1.3 Attaching the console holder to the box Screw the console holder to the box according to the drawing and in the marked spots. Use 4 pcs M5 × 14 mm screw, 4 pcs M5 nut and 8 pcs M5 washer.
3.2 Solar panel mounting Screw the consoles with posts to the solar panel with 4 pcs M5 × 14 mm screw, 4 pcs M5 nut and 8 pcs M5 washer. 2 pcs horizontal consoles · 4 pcs M5 × 14 mm screw ·...
Page 9
Electric fencing +420 730 893 828 Instructions on how to build the console for 100 W solar panel CONTENT 100W panel – console for portable box (Art.No. 8146) (Art.No. 8164) (Art.No. 8150) . . . . . .
• 2 pcs M6 wing nut 1.1 Console assembling Assemble the console parts according to the drawing and screw the parts together at the marked points. Use 8 pcs M5 × 14 mm screw, 8 pcs M5 nut and 16 pcs M5 washer.
1.3 Attaching the console holder to the box Screw the console holder to the box according to the drawing and in the marked locations, use 4 pcs M5 × 14 mm screw, 4 pcs M5 nut and 8 pcs M5 washer.
1.4 Mounting to the box Place the solar panel with the console on the holder so that both vertical parts of the console are seated on the holder from the inside, connect the console with the holder using 2 pcs M6 × 110 mm screw in the marked spots as on the drawing and secure them with 2 pcs M6 wing nut.
M10 × 120 mm screw and an M10 wing nut. To secure tilt of the panel, fit a second M10 × 120 mm screw and an M10 wing nut, according to drawing, in one of the three positions.
3.2 Mounting on the solar panel Screw the console according to the drawing with 4 pcs M5 × 14 mm screw and 4 pcs M5 nut and 8 pcs M5 washer to the panel. · 4 pcs M5 × 14 mm screw ·...
• 2 pcs M10 wing nut 1.1 Console assembling Take the two horizontal parts of the console and put them over each other through, so you have the eight holes as shown in the drawing, put M5 × 14 mm screw in one pair of holes, 2 pcs M5 washer, and add one vertical part of the console.
1.2 Solar panel mounting Screw the assembled consoles to the panel with 4 pcs M5 × 14 mm screw, 4 pcs M5 nut and 8 pcs M5 washer according to the drawing. Align the consoles with the panel and tighten all screws. ·...
M10 × 120 mm screw and an M10 wing nut. To secure tilt of the panel, fit a second M10 × 120 mm screw and an M10 wing nut, according to one of the three positions as shown. The screws must pass through all parts of the console and the mounting post.
· 4 pcs M6 nut extended 2.2 Solar panel mounting Screw the console according to the drawing with 4 pcs M5 × 14 mm screw and 4 pcs M5 nut and 8 pcs M5 washer to the panel. · 4 pcs M5 × 14 mm screw ·...
2.3 Mounting to the box Place the complete set with the mounted console to the solar panel, against the box, connect the panel wires to the wires on the box, place the panel on the box on the inclined side into the the prepared holes, secure the panel from the inside of the box...