1. Manuals
  2. Brands
  3. PI Micos Manuals
  4. Industrial Electrical
  5. LS-270
  6. User manual

PI Micos LS-270 User Manual

Linear stage
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User Manual
6239-9-
Order no.
DC-B-086
2Phase-072
305 mm (12")
508 mm (20")
815 mm (32")
1016 mm (40")
Without LS-010
LS-010, length measuring system (steel)
ILS-020, limit switch (Inductive)
1
2
2
3
4
5
0
1
4
LS-270 Linear Stage
Order no. 6239-9-
User Manual
Version: 00.003
LS-270 Linear Stage 1
Date: 30.06.2023

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LS-270 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for PI Micos LS-270

  • Page 1 User Manual LS-270 Linear Stage 1 LS-270 Linear Stage 6239-9- Order no. Order no. 6239-9- DC-B-086 2Phase-072 User Manual Version: 00.003 Date: 30.06.2023 305 mm (12") 508 mm (20") 815 mm (32") 1016 mm (40") Without LS-010 LS-010, length measuring system (steel)
  • Page 2 2 LS-270 Linear Stage © 2016 PI miCos GmbH, Eschbach, Germany. The text, photographs and drawings in this manual are protected by copyright. With regard thereto, PI miCos GmbH retains all rights. The use of any text, images and drawings is permitted only in part and only when indicating the source.

  • Page 3: Table Of Contents

    LS-270 Linear Stage 3 Technical Features CONTENTS 4.7.1 Load Capacity Data 4.7.2 Motors ABOUT THIS DOCUMENT 4.7.3 Measuring System Objective and Target Group of this User Manual 4.7.4 Limit Switch Symbols and Typographic Conventions 4.7.5 Connector Other Applicable Documents 4.7.6 Technical Data...

  • Page 4: About This Document

    • Basic knowledge on servo systems, motion control concepts and The LS-270 is a laboratory device as defined by DIN EN 61010. It is applicable safety measures is assumed. intended for indoor use and use in an environment which is free of dirt, oil, •...

  • Page 5: General Safety Instructions

    Improper use of the LS-270 can result in personal injury and/or damage to the LS-270. 2.2.2 Measures during Installation Only use the LS-270 for its intended purpose, and only use it if it is in good working order. The LS-270 may be damaged by excessively long screws and wrongly Read the user manual.

  • Page 6: Measures During Start-Up

    Set the control signal so that the moving part does not stop abruptly or try to continue motion at the end of the travel range. • Do not put your LS-270 into operation until it is fully mounted and connected. •...

  • Page 7: Unpacking

    NOTICE 2Phase-072 All specifications in this user manual refer only to the standard products that are included in the PI miCos 305 mm (12") catalog. Any special features that are different, in particular special requests from customers, are supplied with the 508 mm (20")

  • Page 8: Product View

    8 LS-270 Linear Stage Product View WARNING After removing the transport lock (if present), watch out for moving parts. NOTICE Protect the product against mechanical damage (knocking, shock, ...). Never start up an axis if you suspect it to be damaged or broken.
  • Page 9 LS-270 Linear Stage 9 Optional Accessories 4.7.2 Motors DC-B-086 with Encoder For optional accessories, please ask our customer service department (chapter 9) for information on possible use of adapter plates or additional Z- brackets. Motor type DC-brush RS-230C Nominal voltage 22.9...
  • Page 10 10 LS-270 Linear Stage Counter capability Operating temperature °C 0..55 Linear expansion coefficient Approx. 10.5 e-6 Absolute accuracy µm +/- 1 Index position 50 mm starting in the middle of travel Connector Sub-D (m) 2Phase-072 Motor type 2 phase bipolar parallel PK-266M-E2.0B...

  • Page 11: Connector

    LS-270 Linear Stage 11 4.7.5 Connector 2SM motor, Sub-D (m), 25-pin DC brush motor, Sub-D (m), 25-pin, pin assignment with inductive limit switch 2SM motor, Sub-D (m), 25-pin, pin assignment with inductive limit switch Sub-D (m), Function Sub-D (m), Function...

  • Page 12: Technical Data

    12 LS-270 Linear Stage ST-001 Linear encoder, Sub-D (m), 9-pin, RS-422 pin assignment Travel (mm) 1016 Sub-D (m), Function 9-pin 1200 1400 Encoder channel A+ Encoder channel B+ Encoder channel I+ EGND Supply encoder GND Encoder supply Encoder channel A-...

  • Page 13: Ambient Conditions

    LS-270 Linear Stage 13 Ambient Conditions For indoor use only. • The LS-270 was calibrated at an ambient temperature of 20 °C (+/- 3 °C). • The permissible operating temperature is between 5 °C and 40 °C. • The permissible relative humidity is between 20% and 80%.

  • Page 14: Mounting The Stage

    Tightening torques of the mounting screws to be used should not have Mounting the LS-270 values higher than the following: 1. Displace the moving platform of the LS-270 to the center position by • M3 DIN 912 1.5 Nm hand until all of the countersunk holes in the base body required for •...

  • Page 15: Setting Up An Xy System

    2 - Remove the slider plate • Select the mounting position so that the existing fixing holes in the slider of the LS-270 can be used for the additional part to be affixed. • Mount the additional part with the corresponding screws.

  • Page 16: Start-Up

    This stage must be started up with a suitable cable and the associated controllers. MAINTENANCE Depending on the operating conditions and the period of use of the LS-270, the following maintenance measures are required: Maintenance Run The maintenance run is performed to redistribute the existing lubricant on the guidings of the stage.

  • Page 17: Troubleshooting

    If you have questions concerning your system, have the following charge. information ready: Any old PI miCos equipment can be sent free of charge to the following 1. Product codes and serial numbers of all products in the system address: 2.
  • Page 18 18 LS-270 Linear Stage 11. EC Declaration of Conformity An EC Declaration of Conformity has been issued for the LS-270 in accordance with the following European directives: 2014/30/EU, EMC Directive 2011/65/EU, RoHS Directive The applied standards certifying the conformity are listed below.

Table of Contents