Table of Contents
Advertisement
Quick Links
Model 027137-04051
PCB L&T Hand Torque Wrench, 50 ft-lb (5.6 Nm), 12-inch Handle, 3/8-inch Square Drive, 4-Pin
PT Receptacle
Installation and Operating Manual
For assistance with the operation of this product,
contact the PCB Piezotronics, Inc.
Toll-free: 716-684-0001
24-hour SensorLine: 716-684-0001
Fax: 716-684-0987
E-mail: info@pcb.com
Web: www.pcb.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for PCB Piezotronics 027137-04051
Summary of Contents for PCB Piezotronics 027137-04051
- Page 1 PCB L&T Hand Torque Wrench, 50 ft-lb (5.6 Nm), 12-inch Handle, 3/8-inch Square Drive, 4-Pin PT Receptacle Installation and Operating Manual For assistance with the operation of this product, contact the PCB Piezotronics, Inc. Toll-free: 716-684-0001 24-hour SensorLine: 716-684-0001 Fax: 716-684-0987 E-mail: info@pcb.com...
-
Page 2: Repair And Maintenance
Assistance is needed to safely operate equipment PCB Piezotronics is an ISO-9001 certified company whose Damage is visible or suspected calibration services are accredited by A2LA to ISO/IEC Equipment fails or malfunctions 17025, with full traceability to SI through N.I.S.T. - Page 3 CAUTION Refers to hazards that could damage the instrument. NOTE Indicates tips, recommendations and important information. The notes simplify processes and contain additional information on particular operating steps. The following symbols may be found on the equipment described in this manual: This symbol on the unit indicates that high voltage may be present.
- Page 4 PCB工业监视和测量设备 - 中国RoHS2公布表 PCB Industrial Monitoring and Measuring Equipment - China RoHS 2 Disclosure Table 有害物质 镉 汞 铅 (Pb) 六价铬 (Cr(VI)) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 部件名称 (Hg) (Cd) 住房 PCB板 电气连接器 压电晶体 环氧 铁氟龙 电子 厚膜基板 电线 电缆 塑料 焊接...
- Page 5 Component Name Hazardous Substances Lead (Pb) Mercury (Hg) Cadmium (Cd) Chromium VI Polybrominated Polybrominated Compounds Biphenyls (PBB) Diphenyl Ethers (Cr(VI)) (PBDE) Housing PCB Board Electrical Connectors Piezoelectric Crystals Epoxy Teflon Electronics Thick Film Substrate Wires Cables Plastic Solder Copper Alloy/Brass This table is prepared in accordance with the provisions of SJ/T 11364.
- Page 6 Hand Torque-Angle Wrench Installation and Operating Manual For assistance with the operation of this product, contact: RS Technologies Division of PCB Load & Torque, Inc. Toll-Free in USA: 888-684-2894 24-hour SensorLine : 716-684-0001 Fax: 248-888-8266 E-mail: rsinfo@pcbloadtorque.com 10/21/2016...
- Page 7 HAND TORQUE-ANGLE WRENCH OPERATION MANUAL Introduction: Safety Considerations The Model 962 should not be opened by anyone other than factory personnel. There are no user AUTION serviceable parts inside of the Model 962 recorder. Cables can kill your equipment. High voltage electrostatic discharge can damage electrical devices. AUTION Similar to a capacitor, a cable can hold a charge caused by triboelectric transfer, such as that which occurs in the following:...
- Page 8 HAND TORQUE-ANGLE WRENCH OPERATION MANUAL 1.0 INTRODUCTION Specifications Full Scale Output ..... 2 mV/V (output and shunt calibration are matched to within ±0.25% to assure Hand Torque Wrenches manufactured by RS Technologies interchangeability; output is matched for Division of PCB Load & Torque, Inc., are designed to specified English units.
- Page 9 HAND TORQUE-ANGLE WRENCH OPERATION MANUAL 2.0 SAFETY INFORMATION 6.0 SHUNT CALIBRATION Applied loads must be limited to 100% of the rated capacity. Shunt calibration is the known, electrical unbalancing of a Application of loads exceeding rated capacity can lead to strain gage bridge by means of a fixed resistor that is placed, damage of the hand torque wrench and potential injury to the or “shunted”, across one leg of the bridge.
- Page 10 HAND TORQUE-ANGLE WRENCH OPERATION MANUAL During use, a GREEN gyro status light indicates gyro 6.2 Basic Shunt Calibration Procedure operation is normal. The following procedure outlines the basic routine of shunt calibration. The actual calibration procedure performed by If the status light flashes RED, angular velocity has exceeded your data collector may be automated and will differ.
-
Page 11: Troubleshooting
HAND TORQUE-ANGLE WRENCH OPERATION MANUAL Figure 3—Hold the handle of wrench perpendicular to the centerline Figure 6—Do not jerk the handle abruptly or you may get or shank of the fastener. inaccurate and inconsistent readings. 8.0 TROUBLESHOOTING When having difficulty operating the hand torque wrench, refer to the following checklist. -
Page 12: Maintenance
HAND TORQUE-ANGLE WRENCH OPERATION MANUAL Zero Drift 9.0 MAINTENANCE Unconditioned power supply Open circuit or short The hand torque wrenches provided by RS Technologies Loose wiring Division of PCB Load & Torque Inc. are made of durable RFI/EMI interface materials, and are intended for industrial use. However, routine Temperature change maintenance, such as cleaning of electrical connectors, Wrench moved on power ON before... - Page 13 HAND TORQUE-ANGLE WRENCH OPERATION MANUAL MANUAL NUMBER: 51051 MANUAL REVISION: A ECN NUMBER: 37134 RS Technologies Division of PCB Load & Torque, Inc. Toll-Free in USA 888-684-2894 716-684-0001 www.pcbloadtorque.com...
- Page 14 Model Number Revision: E HAND TORQUE WRENCH 027137-04051 ECN #: 53170 OPTION AL VERSION S Performance EN GLISH Optional versions have identical specifications and accessories as listed for the standard model except Measurement Range(Full Scale Capacity) 50 lbf-ft 68 Nm where noted below.
- Page 15 PCB Load & Torque (A Division of PCB Piezotronics, Inc.) REVISIONS claims proprietary rights in the information disclosed hereon. Neither it nor any reproduction thereof will be disclosed to DESCRIPTION others without the written consent of PCB Load and Torque.
Need help?
Do you have a question about the 027137-04051 and is the answer not in the manual?
Questions and answers