Related Manuals for HLA HDN37
Summary of Contents for HLA HDN37
- Page 1 Power Tine Pallet Fork Power Tine Pallet Fork Power Tine Pallet Fork Power Tine Pallet Fork Power Tine Pallet Fork HDN37, HDN HDN37, HDN HDN37, HDN55 Manual # Manual # HDN HDN_10_01 _10_01 March March 201...
- Page 2 - 0 -...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Introduction, General Information, Serial Number…………………... 2 Owner and Operator and Safety Information……………………… 3-6 … Definitions of Safety Terms and Symbols, Accident Prevention …………………………………………….. Safety Instructions …………………………………………………….… Safety Signs Power Unit Specifications……………………………………………… 7 Attachment Specifications…………………………………………….. 7 Installation Instructions………………………………………………… 7 Hydraulic Instructions………………………………………………….. -
Page 4: Introduction, General Information, Serial Number
HLA at the telephone number or address listed on the previous page of this manual. Keep this manual available for reference whenever this product is being handled or used. Provide this manual to any new owners and/or operators. -
Page 5: Owner And Operator And Safety Information
The safety information given in this manual does not replace any safety codes, insurance needs, federal, state and local laws. ACCIDENTS CAN BE PREVENTED WITH YOUR HELP! The best safety device is a careful operator. HLA and your YOU ARE THE KEY TO SAFETY BECAUSE: dealer ask that YOU be that careful, responsible equipment operator. -
Page 6: Safety Instructions
SAFETY INSTRUCTIONS WORK SAFELY – A CAREFUL OPERATOR IS THE BEST INSURANCE AGAINST ACCIDENTS!! WARNING SECTION Use the right tool for the job at hand. Make sure your tools are in good condition for performing the desired function. WARNING When using tools, wear the protective equipment Obey all safety instructions listed in this specified by the tool manufacturer (i.e. - Page 7 • Failure to obey instructions in this section If this product does not fit properly, contact HLA before could result in death or serious injury. operating. • Never place your finger into the mounting plate or 3- WHEN DEALING WITH HYDRAULICS DURING ANY point hitch or loader holes.
-
Page 8: Safety Signs
Safety signs are available free of charge from your Safety signs are available free of charge from your Safety signs are available free of charge from your dealer or from HLA. dealer or from HLA. dealer or from HLA. ITEM... -
Page 9: Power Unit Specifications
IMPORTANT Exceeding any of the recommended power unit specifications • CAN result in damage to your power unit and/or this product and • WILL void all HLA warranties. MAXIMUM FORK SIZE LOADER LIFT CAPACITY Part # Up to 3700 LB. - Page 10 PALLET FORK OPERATION SAFETY FIRST!! READ AND UNDERSTAND THE SAFETY INSTRUCTIONS ( pages 3-5 of BEFORE BEGINNING ANY PALLET FORK OPERATION. this manual) DANGER Failure to obey the following procedure will result in death or serious injury. • Avoid contacting overhead wires. WARNING Failure to obey the following procedures could result in death or serious injury.
-
Page 11: Operation
PALLET FORK MAINTENANCE Regular maintenance is the key to long equipment life and safe operation. It is very important that these maintenance functions be performed as described below. SAFETY FIRST!! READ AND UNDERSTAND THE SAFETY INSTRUCTIONS ( pages 3-5 BEFORE BEGINNING ANY FORK MAINTENANCE OPERATION. of this manual) BEFORE FIRST USE •... -
Page 12: Grease Points
GREASE POINTS PALLET FORK STORAGE We strongly recommend you take the extra time to follow these storage procedures whenever your Pallet Fork will not be used for an extended period of time. It will help you get off to a hassled free start the next time your equipment is needed. -
Page 13: Parts Illustrations
HDN55 / HDN37 ATTACHMENTS Power Tine Pallet Fork... - Page 14 Power Tine Pallet Fork Parts List ITEM QTY PART NUMBER DESCRIPTION LA-HDN55 HDN55 Frame Only Less Attach LA-HDN37 HDN37 Frame Only Less Attach LP-100001 HDN55 48" Right Tine LP-100010 HDN37 48" Right Tine LP-100002 HDN55 48" Left Tine LP-100011 HDN37 48" Left Tine 11-1220 3/8 X 3-3/4 BOLT &...
-
Page 15: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Low hydraulic fluid level. Check and replenish hydraulic fluid. Check and correct hydraulic hose Improper hose hookup. connections. Broken hydraulic line. Check for leaks and replace line. Quick disconnect coupler(s) Hydraulic cylinders Check coupler connections. are not connected or “Flow malfunctioning Replace coupler(s) if necessary. -
Page 16: Warranty Policy
Horst Welding Horst Welding Horst Welding Warranty Policy Warranty Policy Warranty Policy All equipment is sold subject to mutual agreement that it is All equipment is sold subject to mutual agreement that it is All equipment is sold subject to mutual agreement that it is All equipment is sold subject to mutual agreement that it is All equipment is sold subject to mutual agreement that it is All equipment is sold subject to mutual agreement that it is...
Need help?
Do you have a question about the HDN37 and is the answer not in the manual?
Questions and answers